SIST EN 301 908-6 V4.2.1:2010

ETSI EN 301 908-6 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-6 V4.2.1 (2010-03)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-6 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-6 V4.2.1 (2010-03)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-6 V4.2.1 (2010-03)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 35
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 36
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 37
5.3.9.1 Method of test . 37
5.3.9.1.1 Initial conditions . 37
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 38
5.3.10.2 Test requirements . 39
5.3.11 Transmitter adjacent channel leakage power ratio . 39
5.3.11.1 Method of test . 39
5.3.11.1.1 Initial conditions . 39
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-6 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmon
...

Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 12
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 35
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 36
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 37
5.3.9.1 Method of test . 37
5.3.9.1.1 Initial conditions . 37
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 38
5.3.10.2 Test requirements . 39
5.3.11 Transmitter adjacent channel leakage power ratio . 39
5.3.11.1 Method of test . 39
5.3.11.1.1 Initial conditions . 39
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-6 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended)
...

Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 6: Harmonized EN for IMT-2000,
CDMA TDD (UTRA TDD and E-UTRA TDD) (UE)
covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)



Reference
REN/ERM-TFES-005-6
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, TDD, UMTS
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Contents
Intellectual Property Rights . 6
Foreword . 6
Introduction . 7
1 Scope . 8
2 References . 8
2.1 Normative references . 9
2.2 Informative references . 9
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 10
3.3 Abbreviations . 11
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 12
4.2.2 Spectrum emission mask . 12
4.2.2.1 Definition . 12
4.2.2.1.1 3,84 Mcps TDD option . 12
4.2.2.1.2 1,28 Mcps TDD option . 12
4.2.2.1.3 7,68 Mcps TDD option . 12
4.2.2.2 Limits . 13
4.2.2.2.1 3,84 Mcps TDD option . 13
4.2.2.2.2 1,28 Mcps TDD option . 13
4.2.2.2.3 7,68 Mcps TDD option . 14
4.2.2.3 Conformance . 14
4.2.3 Transmitter spurious emis sions . 14
4.2.3.1 Definition . 14
4.2.3.2 Limits . 14
4.2.3.2.1 3,84 Mcps TDD option . 14
4.2.3.2.2 1,28 Mcps TDD option . 15
4.2.3.2.3 7,68 Mcps TDD option . 15
4.2.3.3 Conformance . 16
4.2.4 Maximum output power . 16
4.2.4.1 Definition . 16
4.2.4.2 Limits . 16
4.2.4.3 Conformance . 16
4.2.5 Minimum transmit output power . 16
4.2.5.1 Definition . 16
4.2.5.2 Limits . 16
4.2.5.2.1 3,84 Mcps TDD option . 16
4.2.5.2.2 1,28 Mcps TDD option . 16
4.2.5.2.3 7,68 Mcps TDD option . 16
4.2.5.3 Conformance . 16
4.2.6 Receiver spurious emissions . 16
4.2.6.1 Definition . 16
4.2.6.2 Limits . 17
4.2.6.2.1 3,84 Mcps TDD option . 17
4.2.6.2.2 1,28 Mcps TDD option . 17
4.2.6.2.3 7,68 Mcps TDD option . 17
4.2.6.3 Conformance . 18
4.2.7 Receiver blocking characteristics . 18
4.2.7.1 Definition . 18
4.2.7.2 Limits . 18
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
4.2.7.2.1 3,84 Mcps TDD option . 18
4.2.7.2.2 1,28 Mcps TDD option . 19
4.2.7.2.3 7,68 Mcps TDD option . 19
4.2.7.3 Conformance . 20
4.2.8 Receiver intermodulation characteristics . 20
4.2.8.1 Definition and applicability . 20
4.2.8.2 Limits . 20
4.2.8.2.1 3,84 Mcps TDD option . 20
4.2.8.2.2 1,28 Mcps TDD option . 21
4.2.8.2.3 7,68 Mcps TDD option . 21
4.2.8.3 Conformance . 21
4.2.9 Receiver spurious response . 21
4.2.9.1 Definition . 21
4.2.9.2 Limits . 22
4.2.9.2.1 3,84 Mcps TDD option . 22
4.2.9.2.2 1,28 Mcps TDD option . 22
4.2.9.2.3 7,68 Mcps TDD option . 22
4.2.9.3 Conformance . 22
4.2.10 Receiver adjacent channel selectivity . 22
4.2.10.1 Definition . 22
4.2.10.2 Limits . 23
4.2.10.2.1 3,84 Mcps TDD option . 23
4.2.10.2.2 1,28 Mcps TDD option . 23
4.2.10.2.3 7,68 Mcps TDD option . 23
4.2.10.3 Conformance . 23
4.2.11 Out-of-synchronization handling of output power . 24
4.2.11.1 Definition . 24
4.2.11.2 Limit . 24
4.2.11.2.1 3,84 Mcps TDD option . 24
4.2.11.2.2 1,28 Mcps TDD option . 25
4.2.11.2.3 7,68 Mcps TDD option . 26
4.2.11.3 Conformance . 27
4.2.12 Transmitter adjacent channel leakage power ratio . 27
4.2.12.1 Definition . 27
4.2.12.2 Limits . 27
4.2.12.2.1 3,84 Mcps TDD option . 27
4.2.12.2.2 1,28 Mcps TDD option . 28
4.2.12.2.3 7,68 Mcps TDD option . 28
4.2.12.3 Conformance . 28
5 Testing for compliance with technical requirements . 28
5.1 Environmental conditions for testing . 28
5.2 Interpretation of the measurement results . 28
5.3 Essential radio test suites . 30
5.3.1 Spectrum emission mask . 30
5.3.1.1 Method of test . 30
5.3.1.1.1 Initial conditions . 30
5.3.1.1.2 Procedure . 30
5.3.1.2 Test requirements . 31
5.3.2 Transmitter spurious emis sions . 31
5.3.2.1 Method of test . 31
5.3.2.1.1 Initial conditions . 31
5.3.2.1.2 Procedure . 31
5.3.2.2 Test requirements . 31
5.3.3 Maximum output power . 31
5.3.3.1 Method of test . 31
5.3.3.1.1 Initial conditions . 31
5.3.3.1.2 Procedure . 32
5.3.3.2 Test requirements . 32
5.3.4 Minimum transmit output power . 32
5.3.4.1 Method of test . 32
5.3.4.1.1 Initial conditions . 32
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
5.3.4.1.2 Procedure . 32
5.3.4.2 Test requirements . 33
5.3.5 Receiver spurious emissions . 33
5.3.5.1 Method of test . 33
5.3.5.1.1 Initial conditions . 33
5.3.5.1.2 Procedure . 34
5.3.5.2 Test requirements . 34
5.3.6 Receiver blocking characteristics . 34
5.3.6.1 Method of test . 34
5.3.6.1.1 Initial conditions . 34
5.3.6.1.2 Procedure . 34
5.3.6.2 Test requirements . 35
5.3.7 Receiver intermodulation characteristics . 35
5.3.7.1 Method of test . 35
5.3.7.1.1 Initial conditions . 35
5.3.7.1.2 Procedure . 35
5.3.7.2 Test requirements . 36
5.3.8 Receiver spurious response . 36
5.3.8.1 Method of test . 36
5.3.8.1.1 Initial conditions . 36
5.3.8.1.2 Procedure . 36
5.3.8.2 Test requirements . 36
5.3.9 Receiver adjacent channel selectivity . 36
5.3.9.1 Method of test . 36
5.3.9.1.1 Initial conditions . 36
5.3.9.1.2 Procedure . 37
5.3.9.2 Test requirements . 37
5.3.10 Out-of-synchronization handling of output power . 37
5.3.10.1 Method of test . 37
5.3.10.1.1 Initial conditions . 37
5.3.10.1.2 Procedure . 37
5.3.10.2 Test requirements . 38
5.3.11 Transmitter adjacent channel leakage power ratio . 38
5.3.11.1 Method of test . 38
5.3.11.1.1 Initial conditions . 38
5.3.11.1.2 Procedure . 39
5.3.11.2 Test requirements . 39
Annex A (normative): HS Requirements and conformance Test specifications Table (HS-
RTT) . 40
Annex B (normative): Environmental profile . 42
B.1 General . 42
B.1.1 Introduction . 42
B.1.2 Temperature . 42
B.1.3 Voltage . 42
B.1.4 Test environment . 43
Annex C (informative): The EN title in the official languages . 44
Annex D (informative): Bibliography . 45
History . 46

ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-6 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedur
...