SIST-TS ETSI/TS 102 112-2 V1.1.1:2005

SLOVENSKI STANDARD
01-januar-2005
Storitve in protokoli za napredna omrežja (SPAN) – Preskušanje integracije
omrežja med IN, PLMN in ISDN – 2. del: Proformi izjave o skladnosti izvedbe (ICS)
in delne dodatne informacije za preskušanje izvedbe (IXIT) ter abstraktni
preskušalni niz (ATS)
Services and Protocols for Advanced Networks (SPAN); Network Integration Testing
between IN, PLMN and ISDN; Part 2: Implementation Conformance Statement (ICS),
partial Implementation eXtra Information for Testing (IXIT) proformas and Abstract Test
Suite (ATS)
Ta slovenski standard je istoveten z: ETSI TS 102 112-2 V1.1.1 (2002-10)
ICS:
33.040.40 Podatkovna komunikacijska Data communication
omrežja networks
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Technical Specification
Services and Protocols for Advanced Networks (SPAN);
Network Integration Testing between IN, PLMN and ISDN;
Part 2: Implementation Conformance Statement (ICS),
partial Implementation eXtra Information for Testing (IXIT)
proformas and Abstract Test Suite (ATS)

�
2 ETSI TS 102 112-2 V1.1.1 (2002-10)

Reference
DTS/SPAN-130307-2
Keywords
ATS, IN, ISDN, NIT, PIXIT, PLMN, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.fr
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2002.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI TS 102 112-2 V1.1.1 (2002-10)
Contents
Intellectual Property Rights.4
Foreword.4
1 Scope.5
2 References.5
3 Definitions.6
3.1 Definitions related to conformance testing.6
3.2 Definitions related to test purpose descriptions.6
4 Abbreviations.8
5 Test Configurations.10
6 Conformance to this ICS and IXIT proformas specification.12
7 ATS Conformance.13
Annex A (normative): End-to-end ICS proforma.14
A.1 Guidance for completing the ICS proforma .14
A.1.1 Purposes and structure.14
A.1.2 Abbreviations and conventions .14
A.1.3 Instructions for completing the ICS proforma.15
A.2 Identification of the implementation .15
A.2.1 Date of the statement.16
A.2.2 Implementation Under Test (IUT) identification .16
A.2.3 ICS contact person.16
A.3 Identification of the document .16
A.4 IN Services.17
Annex B (normative): Partial End-to-end IXIT proforma .18
B.1 Instructions for completing the IXIT proforma.18
B.2 Identification summary.18
B.3 Abstract test suite summary .18
B.4 Test campaign report.31
Annex C (normative): Machine Processable (MP) format of end-to-end ATS.32
C.1 The TTCN Graphical form (TTCN.GR) .32
C.2 The TTCN Machine Processable form (TTCN.MP).32
Annex D (informative): Bibliography.33
History .40

ETSI
4 ETSI TS 102 112-2 V1.1.1 (2002-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Services and Protocols for
Advanced Networks (SPAN).
The present document is part 2 of a multi-part deliverable covering the Network Integration Testing between IN, PLMN
and ISDN as identified below:
Part 1: "Test Suite Structure and Test Purposes (TSS&TP)";
Part 2: "Implementation Conformance Statement (ICS), partial Implementation eXtra Information for
Testing (IXIT) proformas and Abstract Test Suite (ATS)".
The present document was developed by EURESCOM P1106 as Deliverable 3 Volume 3, Parts 1 and 2, and made
freely and publicly available to ETSI TC SPAN for publication.
ETSI
5 ETSI TS 102 112-2 V1.1.1 (2002-10)
1 Scope
The present document specifies the Implementation Conformance Statement (ICS) and Implementation eXtra
Information for Testing (IXIT) for Network Integration Testing (NIT) to verify the overall compatibility of for the most
used IN services based on the CS3 and the INAP/CAP/ISUP interworking between the mobile and fix networks.
Network Integration Testing will assure that the appropriate requested features pass between an ISDN subscriber and
the mobile subscriber across the national or international ISUP (ISUP V2) interface and the IN interfaces CAP/INAP.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
[1] ETSI EN 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber Signalling
System No. one (DSS1) protocol; Signalling network layer for circuit-mode basic call control;
Part 1: Protocol specification [ITU-T Recommendation Q.931 (1993), modified]".
[2] ISO/IEC 9646-1: "Information Technology-Open Systems Interconnection- Conformance testing
methodology and framework, Part 1: General Concepts".
[3] ISO/IEC 9646-2: "Information Technology- Open Systems Interconnection- Conformance testing
methodology and framework, Part 2: Abstract Test Suite Specification".
[4] ISO/IEC 9646-3: "Information Technology- Open Systems Interconnection- Conformance testing
methodology and framework, Part 3: The Tree and Tabular Combined Notation".
[5] ETSI TS 124 008: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); Mobile radio interface Layer 3 specification; Core network
protocols; Stage 3 (3GPP TS 24.008 version 3.2.1 Release 1999)".
[6] ETSI TS 129 078: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); Customised Applications for Mobile network Enhanced
Logic (CAMEL) Phase 3; CAMEL Application Part (CAP) specification (3GPP TS 29.078
version 4.0.0 Release 4)".
[7] ETSI EN 301 931-2 (V1.1.2): "Intelligent Network (IN); Intelligent Network Capability Set 3
(CS3); Intelligent Network Application Protocol (INAP); Protocol specification; Part 2: SCF-SSF
interface".
[8] ITU-T Recommendation Q.1601: "Signalling system No. 7 - Interaction between N-ISDN and
INAP CS2".
[9] Contribution to PIR 2.1: NETWORK INTEGRATION TESTING OF G_UMTS WITH GSM,
PSTN AND ISDN; IN Test purposes; version 3.8, 07/09/2001.
[10] How to write nice TTCN – A Style Guide for the P1016 GSM_ISDN-ATS" (MINIT-31-CH04c,
Project P1016).
[11] ISO/IEC 7776: "Information technology - Telecommunications and information exchange between
systems - High-level data link control procedures - Description of the X.25 LAPB-compatible
DTE data link procedures".
ETSI
6 ETSI TS 102 112-2 V1.1.1 (2002-10)
[12] ISO/IEC 8208: "Information technology - Data communications - X.25 Packet Layer Protocol for
Data Terminal Equipment".
[13] ISO/IEC 9646-7: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 7: Implementation Conformance Statements".
[14] ISO/IEC 9646-4: "Information technology - Open Systems Interconnection - Conformance testing
methodology and framework - Part 4: Test realization".
[15] ITU-T Recommendation H.221: "Frame structure for a 64 to 1 920 kbit/s channel in audiovisual
teleservices".
[16] ITU-T Recommendation H.242: "System for establishing communication between audiovisual
terminals using digital channels up to 2 Mbit/s".
[17] ITU-T Recommendation V.110: "Support by an ISDN of data terminal equipments with V-Series
type interfaces".
[18] ITU-T Recommendation X.30: "Support of X.21, X.21 bis and X.20 bis based Data Terminal
Equipments (DTEs) by an Integrated Services Digital Network (ISDN)".
[19] ITU-T Recommendation F.182: "Operational provisions for the international public facsimile
service between subscribers with Group 3 facsimile terminals (Telefax 3)".
3 Definitions
For the purposes of the present document, the following terms and definitions apply.
3.1 Definitions related to conformance testing
Abstract Test Case (ATC): Refer to ISO/IEC 9646-1 [2].
Abstract Test Suite (ATS): Refer to ISO/IEC 9646-1 [2].
Implementation Under Test (IUT): Refer to ISO/IEC 9646-1 [2].
lower tester: Refer to ISO/IEC 9646-1 [2].
Implementation Conformance Statement (ICS) proforma: Refer to ISO/IEC 9646-1 [2].
Implementation eXtra Information for Testing (IXIT) proforma: Refer to ISO/IEC 9646-1 [2].
Point of Control and Observation (PCO): Refer to ISO/IEC 9646-1 [2].
Protocol Implementation Conformance Statement (PICS): Refer to ISO/IEC 9646-1 [2].
Protocol Implementation eXtra Information for Testing (PIXIT): Refer to ISO/IEC 9646-1 [2].
System Under Test (SUT): Refer to ISO/IEC 9646-1 [2].
Test Purpose (TP): Refer to ISO/IEC 9646-1 [2].
3.2 Definitions related to test purpose descriptions
BC=speech: Bearer capability information element with its information transfer capability field set to "speech" and its
user information layer one protocol field set to "G.711 A-law" [2]
BC=3,1 kHz audio: Bearer capability information element with its information transfer capability field set to "3,1 kHz
Audio" and its user information layer one protocol field set to "G.711 A-law" [3]
BC=UDI: Bearer capability information element with its information transfer capability set to "unrestricted digital
information" [1]
ETSI
7 ETSI TS 102 112-2 V1.1.1 (2002-10)
BC=UDI/TA: Bearer capability information element with its information transfer capability set to "unrestricted digital
information with tones/announcements" and its user information layer one protocol field set to "Recommendations
H.221 and H.242" [4]
BC= V110/X30: Bearer capability information element with its information transfer capability set to "unrestricted
digital information" and its user information layer 1 field set to "ITUstandardised rate adaption V.110/X.30", including
sync/async and user rate values [1]
HLC=telephony: High Layer compatibility information element with its high layer characteristics identification field
set to "telephony" [28]
HLC=videotelephony_ic: High Layer compatibility information element with its high layer characteristics
identification field set to "videotelephony (Recommendation F.721)" and its extended audiovisual characteristics field
set to "capability set of initial channel of Recommendation H.221" [4]
HLC = Facsimile G2/G3: High Layer compatibility information element with its high layer characteristics
identification field set to "facsimile group 2/3 (Recommendation F.182)" [1]
HLC=facsimile group 4: High Layer compatibility information element with its high layer characteristics
identification field set to "facsimile group 4 class 1" [1], [5]
HLC=telex: High Layer compatibility information element with its high layer characteristics identification field set to
"telex" [1]
LLC=telematic_term: Low Layer compatibility information element with its user information layer 2 field indicating
"ISO/IEC 7776 DTE-DTE operation" and user information layer 3 field indicating "ISO/IEC 8208" [1], [5]
LLC=voice band data via modem: Low Layer compatibility information element with its user information layer 1
field indicating a "modem type" coding [1]
LLC = V110/X30: Low Layer compatibility information element with its user information layer 1 field indicating
"ITUstandardised rate adaption V.110/X.30" and including sync/async and user rate values [6]
SI=UPVP: Screening Indicator forwarded to the served user coded as "User-provided, verified and passed"
SI=NP: Screening Indicator coded as "Network provided" [1]
PI=PR: Presentation Indicator coded as "Presentation restricted" [1]
TON=international: Type of number coded as "international" [1]
TON=unknown: Type of number coded as "unknown" [1]
NPI=unknown: Numbering plan identification coded as "unknown" [1]
CUG default request: calling user do not include in the outgoing SETUP message a explicit request for the CUG
supplementary service [11]
UI length=32: the length of the User information field of the User-user information element is 35 octets
CF active: call forwarding (U, B or NR) supplementary service is already activated with the address of user C [17]
GSM - Bearer service categories: All bearer service categories provide information transfer between R/S reference
points and allow the use of sub-rate information streams which are rate adapted
GSM-BC=UD: Unrestricted Digital Information (UD); Provides the transfer of unrestricted digital information.
GSM-BC= 3,1 kHz (External to the PLMN): used to select a "3,1 kHz audio" interworking function at the MSC
NOTE: This service category is used when interworking with the ISDN or PSTN "3,1 kHz audio" service and
includes the capability to select a modem at the interworking function. "External to the PLMN" indicates
that the "3,1 kHz audio" service is only used outside of the PLMN, in the ISDN/PSTN. The connection
within the PLMN, user access point to the interworking function, is an unrestricted digital connection.
Alternate Speech/Data: provides the capability to swap between speech and data during a call
ETSI
8 ETSI TS 102 112-2 V1.1.1 (2002-10)
If either the speech or data portion of the call requires a full rate channel, a full rate channel shall be used for the
duration of the call.
The access interface at the mobile station for the data portion is assumed to be a standard data interface. Some means
must be provided to select the speech/data capability.
Speech followed by Data: provides a speech connection first and then at some time while the call is in progress, the
user can switch to a data connection
The user cannot switch back to speech after the data portion. If either the speech or data portion of the call requires a
full rate channel, a full rate channel shall be used from the start of the call. The network may then change to a half rate
channel for the data portion.
GSM teleservices: teleservices supported by a GSM PLMN are described by a number of attributes which are intended
to be largely independent. They are grouped into five categories:
- High layer attributes;
- Low layer attributes (describing the Bearer capabilities which support the Teleservice);
- Information transfer attributes;
- Access attributes;
- General attributes.
GSM-BC= Speech (TS 11): this service provides the transmission of speech information and audible signalling tones
of the PSTN/ISDN
In the GSM PLMN and the fixed network processing technique appropriate for speech such as analogue transmission,
echo cancellation and low bit rate voice encoding may be used.
Alternate speech and facsimile group 3 (TS 61): this Teleservice allows the connection of ITUgroup 3 fax apparatus
(send and/or receive) to the mobile stations of a GSM PLMN
Facsimile connections may be established to/from group 3 apparatus in the PSTN, ISDN or GSM PLMN.
Automatic Facs. group 3 (TS 62): this teleservice allows connection of ITUgroup 3 fax apparatus to and from the
mobile stations of a GSM PLMN
Facsimile connections may be established to and from group 3 apparatus in the PSTN, ISDN or GSM PLMN.
4 Abbreviations
For the purposes of the present document, the following abbreviations apply:
3PTY Three-ParTY conference
ATS Abstract Test Suite
BC Bearer Capability information element
BSC Base Station Controller
BSS Base Station Sub-system
BSS Base Station System
CAMEL Customized Applications for Mobile network Enhanced Logic
CD Call Deflection
CFB Call Forwarding Busy
CFU Call Forwarding Unconditional
CLIP Calling Line Identification Presentation
CLIR Calling Line Identification Restriction
COLP COnnected Line identification Presentation
COLR COnnected Line identification Restriction
CONF CONFerence (add-on)
CUG Closed User Group
CW Call Waiting
ECT Explicit Call Transfer
FPH FreePHone service
GSM Global System for Mobile Communication
ETSI
9 ETSI TS 102 112-2 V1.1.1 (2002-10)
HLC High Layer Compatibility information element
HPLMN Home Public Land Mobile Network
IMSI International Mobile Subscriber Identity
IN Intelligent Network
INAP Intelligent Network Application Part
IP Internet Protocol
ISDN Integrated Services Digital Network
ISUP ISDN User Part
IUT Implementation Under Test
IXIT Implementation eXtra Information for Testing
LLC Low Layer Compatibility information element
MAP Mobile Application Part
MCID Malicious Call IDentification
MS Mobile Station
MS Mobile Subscriber
MSC Mobile Switching Center
MT Mobile Terminal
MT Mobile Terminated
MTC Mobile Terminated Call
MTP Message Transfer Part
NIT Network Integration Testing
PC Preferential CUG
PI Presentation Indicator
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
PLMN Public Land Mobile Network
PSTN Public Switched Telephone Network
SCCP Signaling Connection and Control Part
SCF Service Control Function
SCP Service Control Point
SGSN Serving GPRS Support Node
SI Screening Indicator
SMS Short Message Service
SS7 Signaling System number 7
SSP Service Switching Point
SUB SUBaddressing
TCAP Transaction Capabilities Application Part
TON Type Of Number
TP Terminal Portability
TP Test Plant
TSS Test Suite Structure
TSS&TP Test Suite Structure and Test Purposes
UD Unrestricted Digital information
UMTS Universal Mobile Telecommunications System
UUS User-to-User Signalling
VLR Visitor Location Register
VPLMN Visited Public Land Mobile Network
ETSI
10 ETSI TS 102 112-2 V1.1.1 (2002-10)
5 Test Configurations
Three different test configurations have been defined, which were mapped into abstract test configurations (Test Suite
Configuration Declarations) as shown in the following figures:
Configuration 1 (GSM_II_IN_II_GSM):
SCPA
TC_IN_1
CAP
PCO_IN_A (PCO/PO)
ISUP A
A ISUP
BSSA MSCA SSPA MSCB BSSB
TC_II_1 TC_II_2 TC_G3_2
TC_G3_1
PCO_II_B
PCO_G3_A PCO_II_A PCO_G3_B
(PCO/PO)
(PCO) (PCO/PO) (PCO)
Configuration 2 (GSM_II_IN__IN_II_GSM):
SCPA SCPB
TC_IN_1 TC_IN_2
CAP CAP
PCO_IN_A (PCO/PO) PCO_IN_B (PCO/PO)
ISUP
BSSA MSCA ISUP SSPA
A SSPB MSCB A BSSB
TC_II_1
TC_G3_1 TC_II_2 TC_G3_2
PCO_II_B
PCO_II_A
PCO_G3_A PCO_G3_B
(PCO/PO)
(PCO) (PCO/PO)
(PCO)
NOTE 1: The configuration is used in test case GG_SPN_04.
NOTE 2: The inter-SSP link is regarded as internal.
NOTE 3: The PCO_IN_A and PCO_IN_B have to be configured identically (both used as PCO or both used as PO).

ETSI
11 ETSI TS 102 112-2 V1.1.1 (2002-10)
Configuration 3 (GSM_II_IN_II_GSM_II_GSM):
SCPA
TC_IN_1
CAP
PCO_IN_A (PCO/PO)
A ISUP ISUP BSSB
BSSA MSCA SSP_A MSCB A
TC_II_1 TC_G3_2
TC_G3_1
PCO_II_B PCO_G3_B
PCO_G3_A PCO_II_A
(PCO/PO) (PCO)
(PCO) (PCO/PO)
ISUP
PCO_II_C (PCO/PO)
MSCC
TC_II _3
A
PCO_G3_C (PCO)
BSSC
TC_G3_3
NOTE 1: The configuration is used for test cases GG___SPN_06, GGG__SPNS_CFU_01,
GGG__SPNS_CFNRY_02, GGG_SPNS_CFNRC_03 and GGGG_SPNS_CFB_01.
NOTE 2: PCO_II_B is only used for test case GG___SPN_06. For all CFxx test cases PCO_G3_B is used as an
auxiliary test interface to activate and deactivate call forwarding supplementary services and to trigger the
service itself.
NOTE 3: Depending on the value of Test Suite Parameter P_IN_PCO_Definition the test configuration can be
modified in such a way that the test interfaces become PCO"s or PO"s respectively. The following tables
summarises the possible configurations:

ETSI
12 ETSI TS 102 112-2 V1.1.1 (2002-10)
PCO/PO configuration for Test Suite Configuration Declaration GSM_II_IN_II_GSM:
Value of
P_IN_PCO_Definiton
PCO's
PCO_G3_A PCO - PCO - PCO - PCO - -
PCO_II_A PO PCO PO PCO PO PCO PO PCO -
PCO_IN_A PCO PCO PCO PCO PO PO PO PO PCO
PCO_II_B PO PO PCO PCO PO PO PCO PCO -
PCO_G3_B PCO PCO - - PCO PCO - - -

PCO/PO configuration for Test Suite Configuration Declaration GSM_II_IN_II_GSM_2:
Value of
P_IN_PCO_Definiton
PCO's
PCO_G3_A PCO - PCO - PCO - PCO - -
PCO_II_A PO PCO PO PCO PO PCO PO PCO -
PCO_IN_A PCO PCO PCO PCO PO PO PO PO PCO
PCO_IN_B PCO PCO PCO PCO PO PO PO PO -
PCO_G3_B PCO PCO PCO PCO PCO PCO PCO PCO -
PCO_II_C PO PO PCO PCO PO PO PCO PCO -
PCO_G3_C PCO PCO - - PCO PCO - - -

6 Conformance to this ICS and IXIT proformas
specification
If it claims to conform to the present document, the actual ICS proforma to be filled in by a supplier shall be technically
equivalent to the text of the ICS proforma given in annex A, and shall preserve the numbering/naming and ordering of
the proforma items.
An ICS which conforms to the present document shall be a conforming ICS proforma completed in accordance with the
guidance for completion given in clause A.1.
A test realizer, producing a executable test suite for this ATS specification is required, as specified in ISO/IEC 9646-7,
to produce an augmented partial IXIT proforma conformant with the text of the partial IXIT proforma given in annex B.
An augmented partial IXIT proforma which conforms to this partial IXIT proforma specification shall, as a minimum,
have contents which are technically equivalent to annex B. The augmented partial IXIT proforma may contain
additional questions that need to be answered in order to prepare the Means Of Testing (MOT) for a particular IUT. The
test laboratory may further augment the augmented partial IXIT proforma to produce a IXIT proforma conformant with
this partial IXIT proforma specification.
A IXIT proforma which conforms to this partial IXIT proforma specification shall, as a minimum, have contents which
are technically equivalent to annex B. The IXIT proforma may contain additional questions that need to be answered in
order to prepare the test laboratory for a particular IUT.
ETSI
C_IN_G3_G3 C_IN_G3_G3
C_IN_II_G3 C_IN_II_G3
C_IN_G3_II C_IN_G3_II
C_IN_II_II C_IN_II_II
C_IN_G3_SCP_G3 C_IN_G3_SCP_G3
C_IN_II_SCP_G3 C_IN_II_SCP_G3
C_IN_G3_SCP_II C_IN_G3_SCP_II
C_IN_II_SCP_II C_IN_II_SCP_II
C_IN_SSP C_IN_SSP
13 ETSI TS 102 112-2 V1.1.1 (2002-10)
7 ATS Conformance
The test realizer, producing a Means Of Testing (MOT) and Executable Test Suite (ExTS) for this Abstract Test Suite
(ATS) specification, shall comply with the requirements of ISO/IEC 9646-4. In particular, these concern the realization
of an Executable Test Suite (ExTS) based on each ATS. The test realizer shall provide a statement of conformance of
the MOT to this ATS specification.
An ExTS which conforms to this ATS specification shall contain test groups and test cases which are technically
equivalent to those contained in the ATS in annex C. All sequences of test events comprising an abstract test case shall
be capable of being realized in the executable test case. Any further checking which the test system might be capable of
performing is outside the scope of this ATS specification and shall not contribute to the verdict assignment for each test
case.
A test laboratory which claims to conform to this ATS specification shall use a MOT which conforms to this ATS.
ETSI
14 ETSI TS 102 112-2 V1.1.1 (2002-10)
Annex A (normative):
End-to-end ICS proforma
Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
users of the present document may freely reproduce the ICS proforma in this annex so that it can be used for its
intended purposes and may further publish the completed ICS.
A.1 Guidance for completing the ICS proforma
A.1.1 Purposes and structure
The purpose of this ICS proforma is to provide a mechanism whereby a supplier of an implementation of the
requirements defined by ETSI, may provide information about the implementation in a standardised manner.
The proforma is subdivided into clauses for the following categories of information:
- guidance for completing the proformas;
- identification of the implementation;
- global statement of conformance.
A.1.2 Abbreviations and conventions
The ICS proforma contained in annex A is comprised of information in tabular form in accordance with the guidelines
presented in ISO/IEC 9646-7.
Item column
The item column contains a number which identifies the item in the table.
Item description column
The item description column describes in free text each respective item (e.g. parameters, timers, etc.). It implicitly
means "is supported by the implementation?".
Status column
The following notations, defined in ISO/IEC 9646-7, are used for the status column:
m mandatory - the capability is required to be supported.
o optional - the capability may be supported or not.
n/a not applicable - in the given context, it is impossible to use the capability.
x prohibited (excluded) - there is a requirement not to use this capability in the given context.
o.i qualified optional - for mutually exclusive or selectable options from a set. "i" is an integer which
identifies an unique group of related optional items and the logic of their selection which is
defined immediately following the table.
ci conditional - the requirement on the capability ("m", "o", "x" or "n/a") depends on the support of
other optional or conditional items. "i" is an integer identifying an unique conditional status
expression which is defined immediately following the table.
ETSI
15 ETSI TS 102 112-2 V1.1.1 (2002-10)
Support column
The support column shall be filled in by the supplier of the implementation. The following common notations, defined
in ISO/IEC 9646-7, are used for the support column:
Y or y supported by the implementation
N or n not supported by the implementation
N/A, n/a or - no answer required (allowed only if the status is n/a, directly or after evaluation of a conditional
status)
It is also possible to provide a comment to an answer in the space provided at the bottom of the table.
Values allowed column
The values allowed column contains the type, the list, the range, or the length of values allowed. The following
notations are used:
- range of values: .
EXAMPLE: 5 . 20.
- list of values: , , .,
EXAMPLE 1: 2 ,4 ,6 ,8, 9.
EXAMPLE 2: '1101'B, '1011'B, '1111'B.
EXAMPLE 3: '0A'H, '34'H, 2F'H.
- list of named values: (), (), ., (
EXAMPLE: reject(1), accept(2).
- length: size ( . )
EXAMPLE: size (1 . 8).
Values supported column
The values supported column shall be filled in by the supplier of the implementation. In this column, the values or the
ranges of values supported by the implementation shall be indicated.
A.1.3 Instructions for completing the ICS proforma
The supplier of the implementation shall complete the ICS proforma in each of the spaces provided. In particular, an
explicit answer shall be entered, in each of the support or supported column boxes provided, using the notation
described in clause A.1.2.
If necessary, the supplier may provide additional comments in space at the bottom of the tables, or separately on sheets
of paper.
More detailed instructions may be given at the beginning of the different clauses of the ICS proforma.
A.2 Identification of the implementation
Identification of the Implementation Under Test (IUT), the Integrated Services Digital Network provided by the
European public telecommunications operator, should be filled in so as to provide as much detail as possible regarding
version numbers and configuration options.
The product supplier information and client information should both be filled in if they are different.
ETSI
16 ETSI TS 102 112-2 V1.1.1 (2002-10)
A person who can answer queries regarding information supplied in the ICS and IXIT should be named as the contact
person.
A.2.1 Date of the statement
A.2.2 Implementation Under Test (IUT) identification
IUT name:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
IUT version:
...............................................................................................................................................................................................
A.2.3 ICS contact person
(A person to contact if there are any queries concerning the content of the ICS or IXIT)
Name:
...............................................................................................................................................................................................
Telephone number:
...............................................................................................................................................................................................
Facsimile number:
...............................................................................................................................................................................................
E-mail address:
...............................................................................................................................................................................................
Additional information:
...............................................................................................................................................................................................
...............................................................................................................................................................................................
...............................................................................................................................................................................................
A.3 Identification of the document
This ICS proforma apply to the following standard:
• ETSI TS 124 008 (V3.2.1);
• ETSI TS 129 078 (V4.0.0);
• ETSI EN 301 931-2 (V1.1.2);
• ITU-T Recommendation Q.1601;
• ETSI EN 300 403-1.
Other ETSI standards related to ISDN, DSS1 and PLMN signalling, layer 3 testing.
ETSI
17 ETSI TS 102 112-2 V1.1.1 (2002-10)
A.4 IN Services
Table A.1: IN
Item IN Services Reference Status Support
1 Number Translation and successfull TCs without TS 129 078 o.1
event triggering, tariffing and tariffing EN 301 931-2
Q.1601
2 Number Translation and successfull TCs with event TS 129 078 o.1
triggering EN 301 931-2
Q.1601
3 Number Translation and successfull TCs with TS 129 078 o.1
Tariffing EN 301 931-2
Q.1601
4 Number Translation and unsuccessfull TS 129 078 o.1
EN 301 931-2
Q.1601
5 Selection of all User Interactive Dialogue and TS 129 078 o.1
successfull TCs without assist method EN 301 931-2
Q.1601
6 Selection of all User Interactive Dialogue and TS 129 078 o.1
successfull TCs with assist Method EN 301 931-2
Q.1601
o.1: It is mandatory to support at least one of these options.

Table A.2: IN Services with Supplemtary Services Interaction
Item IN Services with Supplemtary Services Interaction Reference Status Support
1 Number Translation and COLP TS 129 078 o.2

EN 301 931-2
Q.1601
2 Number Translation and CFU TS 129 078 o.2

EN 301 931-2
Q.1601
3 Number Translation and CFNRY TS 129 078 o.2
EN 301 931-2
Q.1601
4 Number Translation and CFNRC TS 129 078 o.2

EN 301 931-2
Q.1601
5 Number Translation and CFB TS 129 078 o.2

EN 301 931-2
Q.1601
o.2: It is mandatory to support at least one of these options.

ETSI
18 ETSI TS 102 112-2 V1.1.1 (2002-10)
Annex B (normative):
Partial End-to-end IXIT proforma
Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
users of the present document may freely reproduce the IXIT proforma in this annex so that it can be used for its
intended purposes and may further publish the completed IXIT.
B.1 Instructions for completing the IXIT proforma
Before running the end-to-end test suite each participating public network operator will need to supply information
concerning the allocation and availability of suitable test numbers which will be required for setting up international
connections.
This clause contains a questionnaire, which shall be completed before performing the national or international
end-to-end test suite. Additional information is used by the testing personnel for selecting and for setting the correct
parameters on the test equipment.
This questionnaire contains only the information required to perform the tests.
B.2 Identification summary
PIXIT number:
...............................................................................................................................................................................................
Date of issue:
...............................................................................................................................................................................................
Issued to:
...............................................................................................................................................................................................
B.3 Abstract test suite summary
Protocol specification: ETSI TS 124 008 (V3.2.1);
ETSI TS 129 078 (V4.0.0);
ETSI EN 301 931-2;
ITU-T Recommendation Q.1601;
ETSI EN 300 403-1.
ATS specification: -
Abstract test method: Remote test method (see ISO/IEC 9646-2)
ETSI
19 ETSI TS 102 112-2 V1.1.1 (2002-10)
Table B.1: Number related IXIT
Item Parameter Value
1 P_G3_IMSI_A
IMSI of GSM Subscriber A
2 P_G3_IMSI_B
IMSI of GSM Subscriber B
3 P_G3_IMSI_C
IMSI of GSM Subscriber C
4 P_G3_NUM_B
Number of GSM subscriber B in
VPLMN
5 P_G3_NUM_B2
Number of GSM subscriber B in
VPLMN; (Rerouted number,Type of
Number: unknown)
6 P_G3_NUM_BARRED
GSM called party number
(barred number)
7 P_G3_NUM_C
Number of GSM subscriber C in
HPLMN
ETSI
20 ETSI TS 102 112-2 V1.1.1 (2002-10)
Table B.2: IN SCCP Parameters
1 P_IN_sccp_scp_pr_class
Sccp param Protocol Class between
SCP and SSP
2 P_IN_sccp_scp_aind
Sccp param Address indicator in
CdpA/CgpA for addressing the SCP
3 P_IN_sccp_scp_spc
Sccp param SPC in CdpA/CgpA for
addressing the SCP
4 P_IN_sccp_scp_ssn
Sccp params SSN in CdpA/CgpA for
addressing the SCP
5 P_IN_sccp_scp_trty
Sccp param Translation Type in
CdpA/CgpA for addressing the SCP

6 P_IN_sccp_scp_numpl
Sccp paramNumbering Plan in
CdpA/CgpA for addressing the SCP
7 P_IN_sccp_scp_enco
Sccp params Encoding Scheme in
CdpA/CgpA
8 P_IN_sccp_scp_nataddr
Sccp param Nature of Address
Indicator in CdpA/CgpA
9 P_IN_sccp_scp_address
Sccp param Address Signals in
CdpA/CgpA for addressing the SCP
10 P_IN_sccp_ssp_aind
Sccp param Adress Indicator in
CdpA/CgpA for addressing the SSP
11 P_IN_sccp_ssp_spc
Sccp param SPC in CdpA/CgpA for
addressing the SCP
12 P_IN_sccp_ssp_ssn
Sccp param SSN in CdpA/CgpA for
addressing the SCP
13 P_IN_sccp_ssp_trty
Sccp param Translation Type in
CdpA/CgpA
14 P_IN_sccp_ssp_numpl
Sccp param Numbering Plan in
CdpA/CgpA for addressing the SSP
15 P_IN_sccp_ssp_enco
Sccp param Encoding Scheme in
CdpA/CgpA for addressing the SSP
ETSI
21 ETSI TS 102 112-2 V1.1.1 (2002-10)
16 P_IN_sccp_ssp_nataddr
Sccp param Natur of Address Indicator
in CdpA/CgpA for addressing the SSP
17 P_IN_sccp_ssp_address
Sccp param Address Signals in
CdpA/CgpA for addressing the SSP
18 P_IN_sccp_scp2_pr_class
Sccp param protocol class between
SCP2 and SSP2
19 P_IN_sccp_scp2_aind
Sccp param Address Indicator in
CdpA/CgpA for addressing the SCP2

20 P_IN_sccp_scp2_spc
Sccp param SPC in CdpA/CgpA for
addressing the SCP2
21 P_IN_sccp_scp2_ssn
Sccp param SSN in CdpA/CgpA for
addressing the SCP2
22 P_IN_sccp_scp2_trty
Sccp param Translation Type in
CdpA/CgpA for addressing the SCP2
23 P_IN_sccp_scp2_numpl
Sccp param Numbering Plan in
CdpA/CgpA for addressing the SCP2
24 P_IN_sccp_scp2_enco
Sccp param Encoding Scheme in
CdpA/CgpA for addressing the SCP2
25 P_IN_sccp_scp2_nataddr
Sccp param Nature of Address
Indicator in CdpA/CgpA for addressing
the SCP2
26 P_IN_sccp_scp2_address
Sccp param Address Signals in
CdpA/CgpA for addressing the SCP2
27 P_IN_sccp_ssp2_aind
Sccp param Address Indicator in
CdpA/CgpA for addressing the SSP2
28 P_IN_sccp_ssp2_spc
Sccp param SPC in CdpA/CgpA for
addressing the SSP2
29 P_IN_sccp_ssp2_ssn
Sccp param SSN in CdpA/CgpA for
addressing the SSP2
30 P_IN_sccp_ssp2_trty
Sccp param Translation Type in
...