iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

oSIST prEN IEC 62217:2024

(Main)

Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria

Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria

Hochspannungs-Polymerisolatoren für Innenraum- und Freiluftanwendung - Allgemeine Begriffe, Prüfverfahren und Annahmekriterien

Isolateurs polymériques à haute tension pour utilisation à l'intérieur ou à l'extérieur - Définitions générales, méthodes d'essai et critères d'acceptation

Polimerni visokonapetostni izolatorji za notranjo in zunanjo uporabo - Splošne definicije, preskusne metode in prevzemna merila

General Information

Status
Not Published
Public Enquiry End Date
29-Feb-2024
ICS
29.080.10 - Insulators
Technical Committee
IZL - Insulators
Current Stage
4020 - Public enquire (PE) (Adopted Project)
Start Date
04-Jan-2024
Due Date
23-May-2024
Ref Project
prEN IEC 62217:2023 - Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria

Relations

Revises
SIST EN 62217:2013 - Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria (IEC 62217:2012)
Effective Date
23-Jan-2023
Revised
SIST EN 62217:2013 - Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and acceptance criteria (IEC 62217:2012)
Effective Date
23-Jul-2019

Buy Standard

prEN IEC 62217:2024 - BARVEprEN IEC 62217:2024 - BARVE
PreviousNext
Draft
prEN IEC 62217:2024 - BARVE
English language
31 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
oSIST prEN IEC 62217:2024
01-februar-2024
Polimerni visokonapetostni izolatorji za notranjo in zunanjo uporabo - Splošne
definicije, preskusne metode in prevzemna merila
Polymeric HV insulators for indoor and outdoor use - General definitions, test methods
and acceptance criteria
Hochspannungs-Polymerisolatoren für Innenraum- und Freiluftanwendung - Allgemeine
Begriffe, Prüfverfahren und Annahmekriterien
Isolateurs polymériques à haute tension pour utilisation à l'intérieur ou à l'extérieur -
Définitions générales, méthodes d'essai et critères d'acceptation
Ta slovenski standard je istoveten z: prEN IEC 62217:2023
ICS:
29.080.10 Izolatorji Insulators
oSIST prEN IEC 62217:2024 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN IEC 62217:2024

---------------------- Page: 2 ----------------------
oSIST prEN IEC 62217:2024
36/589/CDV

COMMITTEE DRAFT FOR VOTE (CDV)
PROJECT NUMBER:
IEC 62217 ED3
DATE OF CIRCULATION: CLOSING DATE FOR VOTING:
2023-12-08 2024-03-01
SUPERSEDES DOCUMENTS:
36/582/RR

IEC TC 36 : INSULATORS
SECRETARIAT: SECRETARY:
Sweden Mr Dan Windmar
OF INTEREST TO THE FOLLOWING COMMITTEES: PROPOSED HORIZONTAL STANDARD:


Other TC/SCs are requested to indicate their interest, if
any, in this CDV to the secretary.
FUNCTIONS CONCERNED:
EMC ENVIRONMENT QUALITY ASSURANCE SAFETY
SUBMITTED FOR CENELEC PARALLEL VOTING NOT SUBMITTED FOR CENELEC PARALLEL VOTING
Attention IEC-CENELEC parallel voting
The attention of IEC National Committees, members of
CENELEC, is drawn to the fact that this Committee Draft
for Vote (CDV) is submitted for parallel voting.
The CENELEC members are invited to vote through the
CENELEC online voting system.

This document is still under study and subject to change. It should not be used for reference purposes.
Recipients of this document are invited to submit, with their comments, notification of any relevant patent rights of
which they are aware and to provide supporting documentation.
Recipients of this document are invited to submit, with their comments, notification of any relevant “In Some
Countries” clauses to be included should this proposal proceed. Recipients are reminded that the CDV stage is
the final stage for submitting ISC clauses. (SEE AC/22/2007 OR NEW GUIDANCE DOC).

TITLE:
Polymeric HV insulators for indoor and outdoor use - General definitions, test methods and
acceptance criteria

PROPOSED STABILITY DATE: 2027

NOTE FROM TC/SC OFFICERS:


Copyright © 2023 International Electrotechnical Commission, IEC. All rights reserved. It is permitted to
download this electronic file, to make a copy and to print out the content for the sole purpose of preparing National
Committee positions. You may not copy or "mirror" the file or printed version of the document, or any part of it,
for any other purpose without permission in writing from IEC.

---------------------- Page: 3 ----------------------
oSIST prEN IEC 62217:2024
IEC CDV 62217 © IEC 2023 2 36/589/CDV

1 CONTENTS
2
3 FOREWORD. 4
4 INTRODUCTION . 6
5 1 Scope . 7
6 2 Normative references . 7
7 3 Terms and definitions . 8
8 4 Identification . 11
9 5 Environmental conditions . 11
10 6 Information on transport, storage and installation . 12
11 7 Classification of tests . 13
12 7.1 Design tests . 13
13 7.2 Type tests . 13
14 7.3 Sample tests . 13
15 7.4 Routine tests . 13
16 8 General requirements for insulator test specimens .
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN IEC 60383-1:2023(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Part 1: Ceramic or glass insulator units for a.c. systems - Definitions, test methods and acceptance criteria
EN IEC 60383-1:2023

This part of IEC 60383 applies to insulators of ceramic material or glass for use on a.c. overhead power lines and overhead traction lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to insulators for use on d.c. overhead electric traction lines.
This part applies to string insulator units, rigid overhead line insulators and to insulators of similar design when used in substations.
lt does not apply to insulators forming parts of electrical apparatus or to parts used in their construction or to post insulators which are covered by IEC 60168: Tests on indoor and outdoor post insulators of ceramic material or glass for systems with nominal voltages greater than 1 000 V.
Tests on insulator strings and insulator sets (for example, wet switching impulse voltage) are dealt with in part 2 of IEC 60383.
The object of this part is:
- to define the terms used
- to define insulator characteristics and to prescribe the conditions under which the specified values of these characteristics shall be verified
- to prescribe test methods
- to prescribe acceptance criteria.
This part does not include requirements dealing with the choice of insulators for specific operating conditions.
Specific requirements on the use of coatings on ceramic or glass insulators are described in the informative Annex C.
NOTE A guide for the choice of insulators under polluted conditions has been published, see IEC 60815-1 and -2.
Numerical values for insulator characteristics are specified in IEC 60305, IEC 60433 and IEC 60720.

  • Standard
    66 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    58 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60433:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic insulators for AC systems - Characteristics of insulator units of the long rod type (IEC 60433:2021)
EN IEC 60433:2021

This International Standard is applicable to string insulator units of the long rod type with
insulating parts of ceramic material intended for use in AC overhead power lines with a
nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It is also
applicable to insulators of similar design, used in substations.
This document is applicable to ceramic string insulator units of the long rod type, either with a
clevis end fitting at both ends for coupling with a tongue, or with a socket end fitting at both
ends for coupling with a pin ball.
The object of this document is to prescribe specified values for electrical and mechanical
characteristics, and for the principal dimensions of ceramic string insulator units of the long
rod type.
This document is applicable to string insulator units for use on overhead lines situated in
lightly polluted areas, and the creepage distances given in Table 1 have been established
accordingly, using the IEC TS 60815-2 recommendation of 27,8 mm/kV for SPS class.
However, shorter creepage distances are applicable for use in some non-polluted areas. If
specific operating conditions require or allow non-standard (longer or shorter) creepage
distances, the mechanical characteristics as well as the lengths L (see Clause 4) of this
document are intended to be used unless the need for exceptionally long creepage distances
requires values of L greater than those given in Table 1. In the case of special requirements,
e.g. very heavy polluted areas and for other particular or extreme environmental conditions, it
may be necessary for certain dimensions to be changed.
As far as reasonably applicable, this document is also applicable to be applied to similar
insulator units outside the scope of this standard, such as insulators for electric traction lines.
This document does not include tests on insulators and dimensions of end fittings.
Ball and socket couplings are covered by IEC 60120, clevis and tongue couplings by
IEC 60471.
NOTE 1 For the definition of site pollution severity, see applicable part of IEC TS 60815.
NOTE 2 The term "ceramic" is used in this document to refer to porcelain materials and, contrary to North
American practice, does not include glass.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60305:2021(Main)
Insulators for overhead lines with a nominal voltage above 1000 V - Ceramic or glass insulator units for AC systems - Characteristics of insulator units of the cap and pin type (IEC 60305:2021)
EN IEC 60305:2021

This International Standard applies to string insulator units of the cap and pin type with
insulating parts of ceramic material or glass, intended for AC overhead lines with a nominal
voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to
insulators of similar design used in substations.
This document applies to string insulator units of the cap and pin type either with ball and
socket couplings or with clevis and tongue couplings.
This document applies to string insulator units for use on overhead lines in clean areas and
polluted areas. For use in areas characterized by very heavy pollution levels and for other
particular or extreme environmental conditions, it may be necessary for certain dimensions to
be changed and insulator units having different creepage distances, spacing and forms may
be preferred (for example, flat profile, hemispherical etc.). Insulators for use on DC systems
may also need different dimensions. In any case, it is applicable that the standardized
mechanical characteristics of this document and coupling sizes are retained.
The object of this document is to prescribe specified values for the mechanical characteristics
and for the main dimensions of string insulator units of the cap and pin type.
The power frequency, lightning impulse and puncture withstand voltages of string insulator
units are not specified in this document. IEC 60383-1 gives the electrical characteristics which
define string insulator units; their values are agreed between purchaser and manufacturer.
Ball and socket couplings are covered by IEC 60120, clevis and tongue couplings by
IEC 60471.
NOTE For the definition of site pollution severity see IEC TS 60815-1.

  • Standard
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60471:2020(Main)
Clevis and tongue couplings of string insulator units - Dimensions (IEC 60471:2020)
EN IEC 60471:2020

This international standard applies to string insulator units of the cap and pin type and also of
the long rod type as well as the fittings used with such insulators.
The object of this document is to define the dimensions of a series of clevis and tongue
couplings to permit the assembly of insulators or fittings supplied by different manufacturers.
NOTE 1 IEC 60305 gives the coordination between the standardized dimensions of Table 1 and the strength
classes of cap and pin insulator. IEC 60433 gives the coordination between the standardized dimensions of Table 2
and the strength classes of long rod insulators.
NOTE 2 If the dimensions given in Table 1 are not sufficient, higher strength classes are given in IEC 60305.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    9 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60372:2020(Main)
Locking devices for ball and socket couplings of string insulator units - Dimensions and tests (IEC 60372:2020)
EN IEC 60372:2020

This international standard is applicable to locking devices used with ball and socket
couplings of string insulator units and used with the corresponding metal fittings standardized
in IEC 60120, when they are supplied separately.
When these locking devices are supplied with an insulator or fitting, they are considered as an
integral part of it. In this case, the relevant test is to be included with those of insulators, as
specified in IEC 60383-1 and IEC 61325. On request, a certificate is to be delivered
confirming that the tests on locking devices as specified in this document have been carried
out. The locking devices are usually supplied with the insulator or corresponding metal fittings.
The object of this document is
• to define the shapes and some standard dimensions for locking devices,
• to define the test methods for locking devices,
• to state the acceptance conditions for supply,
• to give other dimensions for guidance of manufacturing only.
The object of this document does not include the specification of the nature of the material,
and the material covered by the scope of this document does not have a surface coating for
corrosion protection. However, the material which will give rise to significant contact
corrosion(chemical reaction) between the locking device and the ball and socket coupling
does not covered by this document.

  • Standard
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    17 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 60120:2020(Main)
Ball and socket couplings of string insulator units - Dimensions (IEC 60120:2020)
EN IEC 60120:2020

The object of this international standard is to define the dimensions of a series of standard
ball and socket couplings using the standard locking devices (see IEC 60372) in order to
permit the assembly of insulators or metal fittings supplied by different manufacturers.
This document applies to string insulator units of the cap and pin and long rod types and their
associated metal fittings.
For the pin ball and the socket, dimensions apply to the finished product after any surface
treatment.
Extreme positions of the pin ball in the socket are given in Annex A.
Typical examples of gauges for checking the dimensions of pin balls and sockets are given in
Annex B.
NOTE Only the dimensions necessary for assembly are dealt with in this standard. Properties of material and
working loads are not specified. The co-ordination of dimensions with strength classes is specified in IEC 60305
and IEC 60433.

  • Standard
    40 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN IEC 61952-1:2019(Main)
Insulators for overhead lines - Composite line post insulators for AC systems with a nominal voltage greater than 1 000 V - Part 1: definitions, end fittings and designations (IEC 61952-1:2019)
EN IEC 61952-1:2019

This document is applicable to composite line post insulators for AC overhead lines with a nominal voltage greater than 1 000 V and a frequency not greater than 100 Hz. It also applies to line post insulators of similar design used in substations or on electric traction lines. This document applies to line post insulators of composite type, generally with metallic couplings, with and without a base plate. It also applies to such insulators when used in complex structures. It does not apply to hollow insulators adapted for use as line post insulators. The object of this document is to specify the main dimensions of the couplings to be used on the composite line post insulators in order to permit the assembly of insulators or fittings supplied by different manufacturers and to allow, whenever practical, interchangeability with existing installations. It also specifies a standard designation system for composite line post insulators.

  • Standard
    35 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 61466-2:2000/A2:2018(Amendment)
Composite string insulator units for overhead lines with a nominal voltage greater than 1 000 V - Part 2: Dimensional and electrical characteristics (IEC 61466-2:1998/A2:2018)
EN 61466-2:1998/A2:2018
  • Addendum – translation
    8 pages
    Slovenian language
    sale 10% off
    e-Library read for
    1 day
  • Amendment
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 60507:2014/AC:2018(Corrigendum)
Artificial pollution tests on high-voltage ceramic and glass insulators to be used on a.c. systems (IEC 60507:2013/COR1:2018)
EN 60507:2014/AC:2018-09

IEC - Corrected version

  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Corrigendum
    3 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 62772:2017(Main)
Composite Hollow Core Station Post Insulators for substations with a.c. voltage greater than 1000 V and d.c. voltage greater than 1500V- Definitions, test methods and acceptance criteria (IEC 62772:2016)
EN 62772:2016

This International Standard applies to composite hollow core station post insulators consisting
of a load-bearing insulating tube (core) made of resin impregnated fibres an insulating filler
material (e.g. solid, liquid, foam, gaseous – pressurized or unpressurized), a housing (outside
the insulating tube) made of polymeric material (for example silicone or ethylene-propylene)
and metal fixing devices at the ends of the insulating tube. Composite hollow core station post
insulators as defined in this standard are intended for general use in substations in both,
outdoor and indoor environments, operating with a rated AC voltage greater than 1 000 V and
a frequency not greater than 100 Hz or for use in direct current systems with a rated voltage
greater than 1 500 V.
The object of this standard is:
– to define the terms used;
– to prescribe test methods;
– to prescribe acceptance criteria.
All the tests in this standard, apart from the thermal-mechanical test, are performed at normal
ambient temperature. This standard does not prescribe tests that may be characteristic of the
apparatus of which the composite hollow core station post insulator ultimately may form a
part. Further technical input is required in this area.
NOTE 1 "Pressurized" means a permanent gas or liquid pressure greater than 0,05 MPa (0,5 bar) gauge. The gas
can be dry air or inert gases, for example sulphur hexafluoride, nitrogen, or a mixture of such gases.
NOTE 2 "Unpressurized" means a gas or liquid pressure smaller than or equal to 0,05 MPa (0,5 bar) gauge.

  • Standard
    25 pages
    English language
    sale 10% off
    e-Library read for
    1 day