SIST EN 12653:2000/kprA2:2009

SLOVENSKI STANDARD
SIST EN 12653:2000/kprA2:2009
01-april-2009
Stroji za izdelavo obutve ter izdelkov iz usnja in njegovih imitacij - Žebljalniki -
Varnostne zahteve
Footwear, leather and imitation leather manufacturing machines - Nailing machines -
Safety requirements
Maschinen für die Herstellung von Schuhen aus Leder und Kunstleder - Nagelmaschinen
- Sicherheitsanforderungen
Machines pour la fabrication des chaussures et articles en cuir et en matériaux similaires
- Machines à clouer - Exigences de sécurité
Ta slovenski standard je istoveten z: EN 12653:1999/prA2
ICS:
61.060 Obuvala Footwear
SIST EN 12653:2000/kprA2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 12653:2000/kprA2:2009

---------------------- Page: 2 ----------------------

SIST EN 12653:2000/kprA2:2009
EUROPEAN STANDARD
FINAL DRAFT
EN 12653:1999
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
January 2009
ICS 61.060

English Version
Footwear, leather and imitation leather manufacturing machines
- Nailing machines - Safety requirements
Machines pour la fabrication des chaussures et articles en Maschinen für die Herstellung von Schuhen aus Leder und
cuir et en matériaux similaires - Machines à clouer - Kunstleder - Nagelmaschinen - Sicherheitsanforderungen
Exigences de sécurité
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 201.
This draft amendment A2, if approved, will modify the European Standard EN 12653:1999. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12653:1999/prA2:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
Foreword
This document (EN 12653:1999/prA2:2009) has been prepared by Technical Committee CEN/TC 201
“Leather and imitation leather goods and footwear manufacturing machinery - Safety”, the secretariat of which
is held by UNI.
This document is currently submitted to the Unique Acceptance Procedure.
The first reason for amending the published standard EN 12653:1999 is the revision of the EU-Machinery
Directive 98/37/EC into 2006/42/EC, requiring the adaptation of published European Standards cited in the
Official Journal of the European Communities under that Directive.
Additionally at this occasion the normative references have been updated, while also some other limited rather
editorial improvements and corrections have been made.
2

---------------------- Page: 4 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)

1 Modification to the Foreword
th
Replace the 4 paragraph with the following: "For relationship with EU Directive(s), see informative Annexes
ZA and ZB, which are integral parts of this document."

2 Modification to the Introduction
Replace the complete text with the following:

"This document is a type C standard as stated in EN ISO 12100.

The machinery concerned and the extent to which hazards, hazardous situations and hazardous events are
covered are indicated in the scope of this document.

When provisions of this type C standard are different from those which are stated in type A or B standards, the
provisions of this type C standard take precedence over the provisions of the other standards, for machines
that have been designed and built according to the provisions of this type C standard.".


3 Modification to Clause 1
th
In the 4 paragraph, replace "foreseeable misuse, component" with "foreseeable misuse and component".
Replace the last paragraph with the following: "This document is not applicable to nailing machines which are
manufactured before the date of its publication as EN."

4 Modification to Clause 2
Replace the introductory paragraphs with the following: "The following referenced documents are
indispensable for the application of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments) applies.".
Replace EN 292-1 with the following: "EN ISO 12100–1:2003, Safety of machinery — Basic concepts, general
principles for design — Part 1: Basic terminology, methodology (ISO 12100-1:2003)".
Replace EN 292-2 with the following: "EN ISO 12100–2:2003, Safety of machinery — Basic concepts, general
principles for design — Part 2: Technical principles (ISO 12100-2:2003)".
Replace EN 563 with the following: "EN ISO 13732-1:2008, Ergonomics of the thermal environment - Methods
for the assessment of human responses to contact with surfaces - Part 1: Hot surfaces (ISO 13732-1:2006)".
Replace "prEN 894-3" with "EN 894-3".
Replace EN 954-1 with the following: "EN ISO 13849-1, Safety of machinery - Safety-related parts of control
systems - Part 1: General principles for design (ISO 13849-1:2006)".
Replace "EN 999:1998" with "EN 999".
3

---------------------- Page: 5 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
Replace "prEN 1005-2, Safety of machinery - Human physical performance – Part 2: Manual handling of
objects associated with machinery" with "EN 1005-2, Safety of machinery — Human physical performance —
Part 2: Manual handling of machinery and component parts of machinery".
Replace "prEN 1005-3" with "EN 1005-3".
Delete reference "EN 1070".
Replace "prEN 1760-2" with "EN 1760-2:2001".
Delete reference "prEN ISO 3740".
Delete reference "EN ISO 4871".
Delete reference "EN ISO 9614".
Delete reference "EN ISO 11200".
Delete reference "EN ISO 11689".
Replace "prEN 12545" with "EN 12545:2000".
Replace "EN 60204-1:1992, Safety of machinery - Electrical equipment of machines; Part 1: General
requirements (IEC 204-1:1992)" with "EN 60204-1:2006, Safety of machinery — Electrical equipment of
machines — Part 1: General requirements (IEC 60204-1:2005 (modified))".
Delete references to EN 60227-1 and EN 60245-1.
In the title of EN 60947-4-1 replace "(IEC 947-4-1:1990)" with "(IEC 60947-4-1:2000)".
In the title of EN 60947-5-1 replace "(IEC 947-5-1:1997)" with "(IEC 60947-5-1:2003)".
Add the following reference: ”EN 61310-1, Safety of machinery - Indication, marking and actuation - Part 1:
Requirements for visual, acoustic and tactile signals (IEC 61310-1:2007)".

5 Modification to Clause 3
Replace the heading with "Terms and definitions".
Replace the introductory paragraph with the following: "For the purposes of this document, the terms and
definitions given in EN ISO 12100-1:2003 and the following apply.".

6 Modification to 4.1
st
Replace the 1 sentence with the following: "This clause contains all the significant hazards, hazardous
situations and events, as far as they are dealt with in this document, identified by risk assessment as
significant for this type of machinery and which require action to eliminate or reduce the risk.".

4

---------------------- Page: 6 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
7 Modification to Clause 5
Delete the introductory paragraph.

8 Modification to 5.1
Replace the text of 5.1 with the following:
"Machinery shall comply with the safety requirements and/or protective measures of this clause.
In addition, the machine shall be designed according to the principles of EN ISO 12100-2 for relevant but not
significant hazards which are not dealt with by this document.
For hazards which are to be reduced by the application of a type B-standard such as EN 294, EN 547, EN
982, EN 983, EN 60204-1 etc., the manufacturer shall carry out a risk assessment to establish the
requirements of the B-standards which are to be applied.".

9 Modification to 5.2.1.1
st
Delete in the 1 sentence "and 4.2.2.2 of EN 292-2:1991".

10 Modification to 5.2.1.2
st
Replace the 1 sentence with the following: "Fixed enclosing guards and fencing shall be designed in such a
manner that a tool is required for fixing or removal, in accordance with 3.2, 3.9 and 3.10 of EN 953:1997.".
nd
Delete the 2 sentence.
Add a second paragraph as follows: "Fixing systems of fixed guards and fixed covers shall remain attached to
these parts or to the machine when the parts are removed.".

11 Modification to 5.2.2.1
st
In the 1 sentence replace "EN 60204-1:1992" with "EN 60204-1".
rd
In the 3 sentence replace "EN 60204-1:1992" with "EN 60204-1:2006".

12 Modification to 5.2.4
nd
Replace in the 2 sentence "EN 563" with "EN ISO 13732-1".
5

---------------------- Page: 7 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
13 Modification to 5.2.6.1
Replace "3.8 of EN 292-2:1991" with "4.10 of EN ISO 12100-2:2003".

14 Modification to 5.2.6.3
nd st
Replace the 2 indent of the 1 paragraph with "shall, however, as a minimum comply with performance level
"c" as defined in EN ISO 13849-1 with components in accordance with Annex B".

15 Modification to 5.2.7
Replace the text with "The design shall be in accordance with the requirements of EN 547-1, EN 547-2, EN
894-1, EN 1005-2 and EN 1005-3.".

16 Modification to 5.2.8
Replace in the last paragraph "prEN 894-2 and prEN 894-3" with "EN 894-2 and EN 894-3.".

17 Modification to 5.2.9
Replace the text in brackets with "in accordance with 10.7.4 of EN 60204-1:2006" and delete the brackets.

18 Modification to 5.3.1.1
st
Replace item b) of the 1 paragraph with the following: "high pressure to complete the cycle, with a two-hand
control in accordance with type III A of EN 574, positioned in accordance with EN 999. The related parts of the
control system shall as a minimum comply with performance level "c" as defined in EN ISO 13849-1.".

19 Modification to 5.3.1.2
st
Replace item b) of the 1 paragraph with the following: "high pressure to complete the cycle, with a two-hand
control in accordance with type III A of EN 574, positioned in accordance with EN 999. The related parts of the
control system shall as a minimum comply with performance level "c" as defined in EN ISO 13849-1.".
Replace in item c) "prEN 1760-2" with "EN 1760-2".
6

---------------------- Page: 8 ----------------------

SIST EN 12653:2000/kprA2:2009
EN 12653:1999/prA2:2009 (E)
20 Modification to 5.3.2
Replace the text with the following: "A two-hand control in accordance with type III A of EN 574, positioned in
accordance with EN 999, is required for the un-lasted shoe (see 5.3.1.1) and for the sole (see 5.3.1.2, a), b)
and c)). The related parts of the control system shall as a minimum comply with performance level "c" as
defined in EN ISO 13849-1.".

21 Modification to 5.3.4
st
Delete in the 1 sentence "and 4.2.2.2 of EN 292-2:1991".

22 Modification to Clause 6
st st
In the 1 indent of the 1 paragraph replace the text in brackets with "in particular EN ISO 12100-1, EN ISO
12100-2, EN 294, EN ISO 13849-1 and
...