SIST EN 50396:2005/A1:2011
(Amendment)Non electrical test methods for low voltage energy cables
Non electrical test methods for low voltage energy cables
EN 50396 contains non-electrical test methods required for the testing of harmonized low voltage energy cables, especially those rated at up to and including 450/750 V.
NOTE 1 A description of the origin of these test methods and of the background to the EN are given in the Introduction and Annex A.
The particular cable standard dictates the tests which need to be performed on the relevant cable type. It also specifies whether the specific test is a type test (T), a sample test (S) or a routine test (R) for the particular cable type.
NOTE 2 T, S and R are defined in the relevant cable standard.
The requirements to be met during or after the test are specified for the particular cable type in the relevant cable standard. However, some test requirements are obvious and universal, such as the fact that no cracks shall occur during ozone test, and these are stated in the particular test method.
Test methods for use specifically in utility power cables are not covered by this EN. They can be found in HD 605.
Test methods for use specifically in communications cables are the responsibility of CENELEC TC 46X. At present such test methods are given in EN 50289 (series).
Nicht-elektrische Prüfverfahren für Niederspannungskabel und -leitungen
Méthodes d'essais non électriques pour les câbles d'énergie basse tension
Metode za preskušanje neelektričnih lastnosti nizkonapetostnih energetskih kablov - Dopolnilo A1
EN 50396 vsebuje metode za preskušanje neelektričnih lastnosti, potrebne za preskušanje harmoniziranih nizkonapetostnih energetskih kablov, predvsem tistih z nazivno napetostjo do vključno 450/750 V.
OPOMBA 1: Opis izvora teh preskusnih metod in ozadje EN sta podana v uvodu in dodatku A.
Standard za določen kabel narekuje, katere preskuse je treba opraviti na ustrezni vrsti kabla. Določa tudi, ali je pri določeni vrsti kabla določen preskus tipski preskus (T), vzorčni preskus (S) ali rutinski preskus (R).
OPOMBA 2: T, S in R so opredeljeni v standardu za ustrezni kabel.
Zahteve, ki morajo biti izpolnjene med preskusom ali po njem, so opredeljene za določeno vrsto kabla v standardu za ustrezni kabel. Vendar pa so nekatere preskusne zahteve očitne in univerzalne, kot dejstvo, da med ozonskim preskusom ne pride do razpok, in te so navedene v določeni preskusni metodi.
Ta EN ne zajema preskusnih metod, ki se uporabljajo izrecno v priročnih energetskih kablih. Te so navedene v HD 605.
Za preskusne metode, ki se uporabljajo izrecno v komunikacijskih kablih, je odgovoren CENELEC TC 46X. Trenutno so te preskusne metode navedene v (seriji) EN 50289.
General Information
- Status
- Published
- Publication Date
- 07-Apr-2011
- Technical Committee
- IEKA - Electric cables
- Current Stage
- 6060 - National Implementation/Publication (Adopted Project)
- Start Date
- 22-Mar-2011
- Due Date
- 27-May-2011
- Completion Date
- 08-Apr-2011
- Directive
- Not Harmonized2006/95/EC - Directive 2006/95/EC of the European Parliament and of the Council of 12 December 2006 on the harmonisation of the laws of Member States relating to electrical equipment designed for use within certain voltage limits (codified version)OJ Ref: C 348/03 OJ Date: 28-Nov-2013
Harmonized Standard2014/35/EU - Directive 2014/35/EU of the European Parliament and of the Council of 26 February 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of electrical equipment designed for use within certain voltage limitsOJ Ref: C 249/03, UMIK 13.6.2025 OJ Date: 08-Jul-2016
Relations
- Effective Date
- 01-May-2011
Overview
SIST EN 50396:2005/A1:2011 specifies non-electrical test methods for harmonized low voltage energy cables, particularly those rated up to and including 450/750 V. Developed by SIST in alignment with the European Standard EN 50396:2005 and its 2011 amendment, this document supports the evaluation of cable properties unrelated to electrical performance. The standard’s guidelines are essential for ensuring that low voltage energy cables meet necessary safety, durability, and reliability requirements in various operational environments.
These non-electrical test methods are required by specific cable standards, which designate when each test applies-whether as a type test (T), sample test (S), or routine test (R). This approach ensures that all necessary mechanical and physical properties of energy cables are evaluated comprehensively and according to relevant European regulatory frameworks.
Key Topics
Main areas addressed by SIST EN 50396:2005/A1:2011 include:
- Scope of application: Focuses on harmonized low voltage energy cables up to 450/750 V.
- Test categorization: Tests are classified as type (T), sample (S), or routine (R) by the related cable standard.
- Universal test requirements: Certain requirements, such as resistance to cracking in ozone testing, are universally mandated and explicitly detailed.
- Reference to related utility and communication cable standards: The document clarifies that test methods for utility power cables and communication cables are governed by separate standards (HD 605 and EN 50289 series, respectively).
By following the procedures outlined in this standard, manufacturers and laboratories ensure that cables achieve objective criteria for physical integrity, environmental resistance, and material performance, beyond their electrical capabilities.
Applications
Industry professionals rely on SIST EN 50396:2005/A1:2011 in a wide range of practical scenarios, such as:
- Quality and compliance testing: Ensuring compliance with European directives for electrical installation materials by conducting validated non-electrical tests on low voltage energy cables.
- Product type approval: Verifying that newly developed cable designs meet all required non-electrical performance benchmarks before market introduction.
- Routine factory inspections: Integrating specific tests into manufacturing quality control processes to monitor ongoing compliance.
- Sample-based batch assessments: Conducting sample tests to maintain consistent production quality across multiple batches of cables.
This standard is utilized extensively in cable manufacturing, testing laboratories, quality assurance departments, and by regulatory authorities concerned with the performance and safety of energy cables in buildings and various industrial settings.
Related Standards
SIST EN 50396:2005/A1:2011 references or operates alongside several significant standards, including:
- HD 605: Standards for utility power cables, detailing specific test methods relevant for those applications.
- EN 50289 (series): Non-electrical and environmental test methods for communication cables, managed by CENELEC TC 46X.
- Relevant cable standards: Each cable type’s specific standard dictates the application of non-electrical tests defined in SIST EN 50396 and interprets categorizations such as type tests, sample tests, or routine tests.
By adopting SIST EN 50396:2005/A1:2011, organizations help ensure the overall reliability and safety of low voltage energy cable installations, in compliance with recognized European testing best practices for non-electrical characteristics.
Get Certified
Connect with accredited certification bodies for this standard
IMQ S.p.A. (Certification)
Italian electrical product certification.
SLG Prüf- und Zertifizierungs GmbH
German testing and certification body.
UL Solutions
Global safety science company with testing, inspection and certification.
Sponsored listings
Frequently Asked Questions
SIST EN 50396:2005/A1:2011 is a amendment published by the Slovenian Institute for Standardization (SIST). Its full title is "Non electrical test methods for low voltage energy cables". This standard covers: EN 50396 contains non-electrical test methods required for the testing of harmonized low voltage energy cables, especially those rated at up to and including 450/750 V. NOTE 1 A description of the origin of these test methods and of the background to the EN are given in the Introduction and Annex A. The particular cable standard dictates the tests which need to be performed on the relevant cable type. It also specifies whether the specific test is a type test (T), a sample test (S) or a routine test (R) for the particular cable type. NOTE 2 T, S and R are defined in the relevant cable standard. The requirements to be met during or after the test are specified for the particular cable type in the relevant cable standard. However, some test requirements are obvious and universal, such as the fact that no cracks shall occur during ozone test, and these are stated in the particular test method. Test methods for use specifically in utility power cables are not covered by this EN. They can be found in HD 605. Test methods for use specifically in communications cables are the responsibility of CENELEC TC 46X. At present such test methods are given in EN 50289 (series).
EN 50396 contains non-electrical test methods required for the testing of harmonized low voltage energy cables, especially those rated at up to and including 450/750 V. NOTE 1 A description of the origin of these test methods and of the background to the EN are given in the Introduction and Annex A. The particular cable standard dictates the tests which need to be performed on the relevant cable type. It also specifies whether the specific test is a type test (T), a sample test (S) or a routine test (R) for the particular cable type. NOTE 2 T, S and R are defined in the relevant cable standard. The requirements to be met during or after the test are specified for the particular cable type in the relevant cable standard. However, some test requirements are obvious and universal, such as the fact that no cracks shall occur during ozone test, and these are stated in the particular test method. Test methods for use specifically in utility power cables are not covered by this EN. They can be found in HD 605. Test methods for use specifically in communications cables are the responsibility of CENELEC TC 46X. At present such test methods are given in EN 50289 (series).
SIST EN 50396:2005/A1:2011 is classified under the following ICS (International Classification for Standards) categories: 29.060.20 - Cables. The ICS classification helps identify the subject area and facilitates finding related standards.
SIST EN 50396:2005/A1:2011 has the following relationships with other standards: It is inter standard links to SIST EN 50396:2005. Understanding these relationships helps ensure you are using the most current and applicable version of the standard.
SIST EN 50396:2005/A1:2011 is associated with the following European legislation: EU Directives/Regulations: 2006/95/EC, 2014/35/EU. When a standard is cited in the Official Journal of the European Union, products manufactured in conformity with it benefit from a presumption of conformity with the essential requirements of the corresponding EU directive or regulation.
SIST EN 50396:2005/A1:2011 is available in PDF format for immediate download after purchase. The document can be added to your cart and obtained through the secure checkout process. Digital delivery ensures instant access to the complete standard document.
Standards Content (Sample)
SLOVENSKI STANDARD
01-maj-2011
0HWRGH]DSUHVNXãDQMHQHHOHNWULþQLKODVWQRVWLQL]NRQDSHWRVWQLKHQHUJHWVNLK
NDEORY'RSROQLOR$
Non electrical test methods for low voltage energy cables
Nicht-elektrische Prüfverfahren für Niederspannungskabel und -leitungen
Méthodes d'essais non électriques pour les câbles d'énergie basse tension
Ta slovenski standard je istoveten z: EN 50396:2005/A1:2011
ICS:
29.060.20 Kabli Cables
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD
EN 50396/A1
NORME EUROPÉENNE
March 2011
EUROPÄISCHE NORM
ICS 29.060.20
English version
Non electrical test methods for low voltage energy cables
Méthodes d'essais non électriques pour Nicht-elektrische Prüfverfahren für
les câbles d'énergie basse tension Niederspannungskabel und -leitungen
This amendment A1 modifies the European Standard EN 50396:2005; it was approved by CENELEC on
2011-03-14. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this amendment the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This amendment exists in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CENELEC member into its own language and notified to the
Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus,
the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I
...