SIST EN 60534-3-1:2001

SLOVENSKI STANDARD
SIST EN 60534-3-1:2001
01-april-2001
Industrial-process control valves - Part 3-1: Dimensions - Face-to-face dimensions
for flanged, two-way, globe-type, straight pattern and centre-to-face dimensions
for flanged, two-way, globe-type, angle pattern control valves
Industrial-process control valves -- Part 3-1: Dimensions - Face-to-face dimensions for
flanged, two-way, globe-type, straight pattern and centre-to-face dimensions for flanged,
two-way, globe-type, angle pattern control valves
Stellventile für die Prozeßregelung -- Teil 3-1: Abmessungen - Einbaulängen von
geflanschten Durchgangsventilen und geflanschten Eckventilen
Vannes de régulation des processus industriels -- Partie 3-1: Dimensions - Dimensions
face à face des vannes de régulation à soupape, à deux voies, à brides, à tête droite et
dimensions face à axe des vannes de régulation à soupape, à deux voies, à brides,
d'équerre
Ta slovenski standard je istoveten z: EN 60534-3-1:2000
ICS:
23.060.40 7ODþQLUHJXODWRUML Pressure regulators
25.040.40 Merjenje in krmiljenje Industrial process
industrijskih postopkov measurement and control
SIST EN 60534-3-1:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 60534-3-1:2001

---------------------- Page: 2 ----------------------

SIST EN 60534-3-1:2001

---------------------- Page: 3 ----------------------

SIST EN 60534-3-1:2001

---------------------- Page: 4 ----------------------

SIST EN 60534-3-1:2001

---------------------- Page: 5 ----------------------

SIST EN 60534-3-1:2001

---------------------- Page: 6 ----------------------

SIST EN 60534-3-1:2001
IEC 60534-3-1
Edition 1.0 2001-01
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE


Industrial-process control valves –
Part 3-1: Dimensions – Face-to-face dimensions for flanged, two-way, globe-
type, straight pattern and centre-to-face dimensions for flanged, two-way, globe-
type, angle pattern control valves

Vannes de régulation des processus industriels –
Partie 3-1: Dimensions – Dimensions face à face des vannes de régulation à
soupape, à deux voies, à brides, à tête droite et dimensions face à axe des
vannes de régulation à soupape, à deux voies, à brides, d’équerre

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
PRICE CODE
INTERNATIONALE
G
CODE PRIX
ICS 23.060; 25.040.40 ISBN 2-8318-5573-X
® Registered trademark of the International Electrotechnical Commission
Marque déposée de la Commission Electrotechnique Internationale

---------------------- Page: 7 ----------------------

SIST EN 60534-3-1:2001
60534-3-1 © IEC:2001 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
––––––––––––
INDUSTRIAL-PROCESS CONTROL VALVES –
Part 3-1: Dimensions – Face-to-face dimensions for flanged,
two-way, globe-type, straight pattern and centre-to-face
dimensions for flanged, two-way, globe-type,
angle pattern control valves
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60534-3-1 has been prepared by subcommittee 65B: Devices, of
IEC technical committee 65: Industrial-process measurement and control.
This bilingual version, published in 2001-01, corresponds to the English version.
The text of this standard is based on the following documents:
FDIS Report on voting
65B/392/FDIS 65B/398/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 3.
The committee has decided that the contents of this publication will remain unchanged
until 2006. At this date, the publication will be
• reconfirmed;
• withdrawn;
...