SIST EN 14215:2018

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Textile Bodenbeläge - Einstufung von maschinengefertigten abgepassten Polteppichen und LäufernRevêtements de sol textiles - Classification des carpettes et passages à velours manufacturésTextile floor coverings - Classification of machine-made rugs and runners97.150Talne oblogeFloor coveringsICS:Ta slovenski standard je istoveten z:EN 14215:2018SIST EN 14215:2018en,fr,de01-december-2018SIST EN 14215:2018SLOVENSKI
STANDARDSIST EN 14215:20131DGRPHãþD



SIST EN 14215:2018



EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 14215
October
t r s z ICS
{ yä s w r Supersedes EN
s v t s wã t r s uEnglish Version
Textile floor coverings æ Classification of machineæmade rugs and runners Revêtements de sol textiles æ Classification des carpettes et passages à velours manufacturés
Textile Bodenbeläge æ Klassifizierung von maschinengefertigten Teppichen und Läufern This European Standard was approved by CEN on
s y June
t r s zä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Rue de la Science 23,
B-1040 Brussels
9
t r s z CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s v t s wã t r s z ESIST EN 14215:2018



EN 14215:2018 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Identification requirements . 5 5 Basic requirements . 6 6 Classification for level of use intensity . 6 7 Luxury classification . 7 8 Additional characteristics . 7 8.1 General . 7 8.2 Castor chair suitability for occasional use . 7 8.3 Suitability for use on stairs (runners only) . 7 9 Report . 7 Annex A (normative)
Method to determine the calculated surface pile density . 8 Annex B (normative)
Criteria for the assessment of stair suitability . 9 Annex C (normative)
Summary test report . 12 Annex D (normative)
Lists of references . 13
SIST EN 14215:2018



EN 14215:2018 (E) 3 European foreword This document (EN 14215:2018) has been prepared by Technical Committee CEN/TC 134 “Resilient, textile and laminate floor coverings”, the secretariat of which is held by NBN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2019, and conflicting national standards shall be withdrawn at the latest by April 2019. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 14215:2013. In comparison with the previous edition, the following technical modifications have been made: — the title has been corrected removing the word 'pile'; — 3 normative references have been updated. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 14215:2018



EN 14215:2018 (E) 4 1 Scope This European Standard specifies requirements for machine-made (woven, tufted, knitted, needled, flocked, bonded, hand-tufted) rugs and runners, including a classification according to use intensity and luxury. This European Standard is not applicable to hand-knotted rugs, to barrier mats or to bathroom rugs. 2 Normative references The following documents are referred to in the text in such a way that some or all of their content constitutes requirements of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 985, Textile floor coverings — Castor chair test EN 14159, Textile floor coverings — Requirements for tolerances on (linear) dimensions of rugs, runners, carpet tiles and wall-to-wall carpet and for tolerances on pattern repeat EN ISO 105-B02, Textiles — Tests for colour fastness — Part B02: Colour fastness to artificial light: Xenon arc fading lamp test (ISO 105-B02) EN ISO 105-E01, Textiles — Tests for colour fastness — Part E01: Colour fastness to water (ISO 105-E01) EN ISO 105-X12, Textiles — Tests for colour fastness — Part X12: Colour fastness to rubbing (ISO 105-X12) EN ISO 9405, Textile floor coverings — Assessment of changes in appearance (ISO9405) EN ISO 12951, Textile floor coverings — Determination of mass loss, fibre bind and stair nosing appearance change using the Lisson Tretrad machine (ISO 12951) ISO 1763, Carpets — Determination of number of tufts and/or loops per unit length and per unit area ISO 1765, Machine-made textile floor coverings — Determination of thickness ISO 1766, Textile floor coverings -- Determination of thickness of pile above the substrate ISO 2424:2007, Textile floor coverings — Vocabulary ISO 4919, Carpets — Determination of tuft withdrawal force ISO 8543, Textile floor coverings — Methods for determination of mass ISO 10361, Textile floor coverings — Production of changes in appearance by means of Vettermann drum and hexapod tumbler tester 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 2424:2007 and the following apply. 3.1 SPT thickness of pile above the substrate in mm SIST EN 14215:2018



EN 14215:2018 (E) 5 3.2 SPW mass of pile per unit area above the substrate in g/m2 3.3 SPD surface pile density in g/cm3 3.4 SPDc calculated surface pile density 3.5 NZ number of tufts/loops per dm2 3.6 FD fibre density factor 4 Identification requirements This clause specifies the requirements for the identification of the product and tolerances for the identifying properties. The manufacturer of machine made rugs and runners shall provide information on the following in accordance with the terms and definitions according to ISO 2424: — commercial references, — type of production technique, — type of use surface, — type of secondary backing (if applicable), and shall declare the values of the characteristics listed in Table 1 using the test methods specified therein. The tolerances of the characteristics shall be in accordance with Table 1. Table 1 — Identification requirements Characteristics Test method Tolerances Fibre composition of use-surface Regulation EU N° 1007/2011
Dimensions EN 14159 EN 14159 Total thickness mm ISO 1765 ±10 % Total mass per unit area g/m2 ISO 8543 ±10 % If applicable: Mass of pile per unit area above the substrate (SPW) g/m2 ISO 8543 ±10 % If applicable: Number of tufts/loops per unit area (Nz) ISO 1763 ±10 % If applicable: Surface pile density (SPD) in g/cm3 ISO 8543 ±10 % SIST EN 14215:2018



EN 14215:2018 (E) 6 5 Basic requirements The general properties of machine-made rugs and runners shall be in accordance with Table 2 when tested in accordance with the test methods therein. Table 2 — Basic requirements Characteristics Requirements Test methods Colour fastness to light -man-made fibres -natural fibres
· 5
· 4 EN ISO 105-B02 Colour fastness to rubbing - dry - wet
· 3 - 4
· 3 EN ISO 105-X12 Colour fastness to Water (change in colour)
EN ISO 105-E01 - plain rugs and runners
· 3 - 4
- patterned and with tonal effect Water (staining)
· 4
- all rugs and runners
· 2 - 3 a
Tuft withdrawal force: cut pile rugs b 3,0 N (average, with no individual result below 1,5 N) ISO 4919 Tuft withdrawal force: loop pile rugs b 10,0 N (average, with no individual result below 5,0 N) ISO 4919 Fibre bind (synthetic loop rugs and runners without pile only) fuzzing, hairiness below level of reference photographs EN ISO 12951, test C (200 cycles) a On multi fibre: worst result. b A representative number or tufts/loops shall be sampled, taking into account the binding. 6 Classification for level of use intensity Machine-made rugs and runners shall be classified for level of use intensity in accordance with the requirements of Table 3 (for all classes). For pile rugs and runners classified as class 23, SPDC (g/cm3) shall be minimum 0,12 and SPW (g/m2) shall be minimum 1 500 g/m2. Annex A defines the method to determine the calculated surface pile density. The change in appearance is determined in accordance with ISO 10361 in either the Hexapod or the Vettermann apparatus using the number of cycles for long term tests. The tested specimens shall be assessed in accordance with EN ISO 9405 and the median grade for overall change in appearance shall meet the requirements specified in Table 3. SIST EN 14215:2018



EN 14215:2018 (E) 7 Table 3 — Classification for use intensity – Change in appearance – Requirements Class Vettermann (20 000 cycles) or Hexapod (12 000 cycles) (ISO 10361) Change of appearance rating (EN ISO 9405) 21 2 22 3 23 4 7 Luxury classification Machine-made rugs and runners without pile shall be classified as LC1. Machine-made pile rugs and runners shall be classified as specified in Table 4. Table 4 — Luxury class by mass of pile per unit area above the substrate Luxury class SPW (in g/m2) According to ISO 8543 LC1 < 600 LC2
· 600 LC3
· 800 LC4
· 1 000 LC5
· 1 500 8 Additional characteristics 8.1 General The following additional claims may be made for products described in this document. 8.2 Castor chair suitability for occasional use If a claim for castor chair suitability for occasional use is made, the product shall meet the requirement for an occasional use r
· 2,0 when tested according to EN 985, Test A. 8.3 Suitability for use on stairs (runners only) The product shall meet the requirement specified in Annex B when tested to EN ISO 12951. 9 Report The results taken from the test reports of the individual test required for classification shall be summarized as shown in Annex C. SIST EN 14215:2018



EN 14215:2018 (E) 8 Annex A (normative)
Method to determine the calculated surface pile density The following formula shall be used to calculate the calculated surface pile density: ××C-3SPW
10SPD= SPT
FD Surface pile thickness (SPT) shall be determined in accordance with ISO 1766. The fibre density factors (FD) are as follows:
acrylic 1,12
cotton 1,50
polyamide 1,14
polyester 1,38
polypropylene 0,91
silk 1,25
viscose 1,52
wool 1,32 In the case of fibre blends, the minimum requirements are calculated on a pro-rata basis according to the fibre blend. SIST EN 14215:2018



EN 14215:2018 (E) 9 Annex B (normative)
Criteria for the assessment of stair suitability This annex shall be used only for runners that are intended to be installed without the use of protective stair nosing. For runners that are intended to be installed using protective stair nosing, the overall use class shall determine the stair suitability. For loop pile runners, the thickness of the pile above the substrate measured according to ISO 1766 shall be
¶ 12 mm. For
...