iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST EN 300 341 V2.1.1:2016

(Main)

Land Mobile Service - Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Land Mobile Service - Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

REN/ERM-TGDMR-352

Storitev kopenskih mobilnih komunikacij - Radijska oprema z vgrajeno anteno, ki oddaja signale za vzbuditev specifičnega odziva v sprejemniku - Harmonizirani standard, ki zajema bistvene zahteve člena 3.2 direktive 2014/53/EU

Ta dokument se uporablja za sisteme kotne modulacije s konstantno ovojnico v storitvi kopenskih mobilnih komunikacij, ki uporabljajo razpoložljivo pasovno širino, delujejo na radijskih frekvencah med 30 MHz in 1 GHz, vključujejo medkanalske razmike 12,5 kHz, 20 kHz in 25 kHz ter so namenjeni za oddajanje in/ali sprejemanje signalov, ki se uporabljajo za vzbuditev specifičnega odziva v sprejemniku.
Ta dokument se uporablja za negovorno opremo in negovorni del kombinirane govorno-negovorne analogne opreme. V tem dokumentu je negovorna radijska oprema opredeljena kot radijska oprema, ki oddaja signal za vzbuditev specifičnega odziva v sprejemniku. Oprema obsega oddajnik ter ustrezen kodirnik in/ali sprejemnik ter ustrezen odkodirnik. Kodirnik in/ali odkodirnik sta lahko ločena kosa opreme. V tem primeru
skladnost s tem dokumentom zajema kodirnik in/ali dekodirnik v povezavi z oddajno in/ali sprejemno opremo.
V tem dokumentu so podane različne zahteve za različne radiofrekvenčne pasove, medkanalske razmike, okoljske pogoje in vrste opreme, kjer je ustrezno.
Ta dokument zajema naslednjo vrsto opreme: prenosne postaje z vgrajenimi antenami. Ta dokument vsebuje zahteve, s katerimi se dokazuje, da »... je radijska oprema sestavljena tako, da učinkovito uporablja in tudi podpira učinkovito uporabo radijskega spektra, tako da ne pride do škodljivih motenj«, ter da »... radijska oprema podpira določene funkcije, ki zagotavljajo dostop do storitev za nujne primere« [i.5].
Poleg tega dokumenta se za opremo na področju uporabe tega dokumenta uporabljajo tudi drugi standardi EN, ki določajo tehnične zahteve v zvezi z bistvenimi zahtevami iz drugih delov 3. člena direktive o radijski opremi [i.5].

General Information

Status
Published
Public Enquiry End Date
20-Mar-2016
Publication Date
13-Apr-2016
ICS
33.060.99 - Other equipment for radiocommunications
33.070.01 - Mobile services in general
Technical Committee
MOC - Mobile Communications
Current Stage
6060 - National Implementation/Publication (Adopted Project)
Start Date
08-Apr-2016
Due Date
13-Jun-2016
Completion Date
14-Apr-2016
Directive
1999/5/EC - Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity
2014/53/EU - Directive 2014/53/EU of The European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC
Ref Project
ETSI EN 300 341 V2.1.1 (2016-03) - Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU

Buy Standard

EN 300 341 V2.1.1:2016EN 300 341 V2.1.1:2016
PreviousNext
Standard
EN 300 341 V2.1.1:2016
English language
62 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day
ETSI EN 300 341 V2.1.1 (2016-03) - Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EUETSI EN 300 341 V2.1.1 (2016-03) - Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
PreviousNext
Standard
ETSI EN 300 341 V2.1.1 (2016-03) - Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
English language
62 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.DUPRQL]LUDQL(8Land Mobile Service - Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 300 341 V2.1.1 (2016-03)SIST EN 300 341 V2.1.1:2016en01-junij-2016SIST EN 300 341 V2.1.1:2016SLOVENSKI
STANDARD



SIST EN 300 341 V2.1.1:2016



ETSI EN 300 341 V2.1.1 (2016-03) Land Mobile Service; Radio equipment using an integral antenna transmitting signals to initiate a specific response in the receiver; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 341 V2.1.1:2016



ETSI ETSI EN 300 341 V2.1.1 (2016-03) 2
Reference REN/ERM-TGDMR-352 Keywords analogue, mobile, PMR, radio, signalling ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 341 V2.1.1:2016



ETSI ETSI EN 300 341 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Modal verbs terminology . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 7 2.2 Informative references . 8 3 Definitions, symbols and abbreviations . 8 3.1 Definitions . 8 3.2 Symbols . 8 3.3 Abbreviations . 9 4 Speech equipment with signalling . 9 5 General and operational requirements . 10 5.1 General . 10 5.1.1 Environmental profile . 10 5.1.2 Choice of model for testing . 10 6 Test conditions, power sources and ambient temperatures . 10 6.1 Normal and extreme test conditions . 10 6.2 Test power source . 10 6.3 Normal test conditions . 11 6.3.1 Normal temperature and humidity . 11 6.3.2 Normal test power source . 11 6.3.2.1 Mains voltage . 11 6.3.2.2 Regulated lead-acid battery power sources used on vehicles . 11 6.3.2.3 Other power sources . 11 6.4 Extreme test conditions . 11 6.4.1 Extreme temperatures . 11 6.4.2 Extreme test source voltages . 12 6.4.2.1 Mains voltage . 12 6.4.2.2 Regulated lead-acid battery power sources used on vehicles . 12 6.4.2.3 Power sources using other types of batteries . 12 6.4.2.4 Other power sources . 12 6.5 Procedure for tests at extreme temperatures . 12 6.5.0 Thermal Balance. 12 6.5.1 Procedure for equipment designed for continuous operation . 12 6.5.2 Procedure for equipment designed for intermittent operation . 12 7 General conditions of measurement . 13 7.1 Normal test signals, test conditions and the unwanted test signals. 13 7.2 Artificial antenna . 13 7.3 Test sites and general arrangements for radiated measurements . 13 7.4 Transmitter automatic shut-off facility . 13 7.5 Modes of operation of the transmitter . 13 7.6 Arrangements for test signals at the input of the receiver via a test fixture or a test antenna . 14 7.7 Receiver mute or squelch facility . 14 7.8 Encoder for receiver measurements . 14 7.9 Facilities for access between the receiver demodulator output and its decoder . 14 7.10 Calling indicator . 14 7.11 Reset . 14 7.12 Reset time . 14 8 Technical characteristics of the transmitter . 15 8.1 Frequency error . 15 8.1.0 Applicability . 15 8.1.1 Definition . 15 SIST EN 300 341 V2.1.1:2016



ETSI ETSI EN 300 341 V2.1.1 (2016-03) 4 8.1.2 Method of measurement . 15 8.1.3 Limits . 15 8.2 Effective radiated power . 16 8.2.0 Applicability . 16 8.2.1 Definition . 16 8.2.2 Method of measurement . 16 8.2.2.1 Maximum effective radiated power under normal test conditions . 16 8.2.2.2 Average effective radiated power under normal test conditions . 18 8.2.3 Method of measurements of maximum and average effective radiated power under extreme test conditions . 19 8.2.4 Limits . 19 8.3 Adjacent and alternate channel power . 20 8.3.0 Applicability . 20 8.3.1 Definition . 20 8.3.2 Method of measurement . 20 8.3.3 Limits . 21 8.4 Radiated spurious emissions . 21 8.4.0 Applicability . 21 8.4.1 Definition . 22 8.4.2 Method of measurement . 22 8.4.3 Limits . 24 8.5 Transient frequency behaviour of the transmitter . 24 8.5.0 Applicability . 24 8.5.1 Definitions . 24 8.5.2 Method of measurement . 25 8.5.3 Limits . 28 9 Technical characteristics of the receiver . 28 9.1 Average usable sensitivity (field strength, responses) . 28 9.1.0 Applicability . 28 9.1.1 Definition . 28 9.1.2 Method of measurement under normal test conditions . 28 9.1.3 Method of measurement of the average usable sensitivities under extreme test conditions . 30 9.1.4 References for degradation measurements . 30 9.1.4.1 Definition . 30 9.1.4.2 Procedures for measurements using the test fixture . 31 9.1.4.3 Procedures for measurements using the test site . 31 9.1.5 Limits . 31 9.2 Co-channel rejection . 32 9.2.0 Applicability . 32 9.2.1 Definition . 32 9.2.2 Method of measurement . 32 9.2.3 Limits . 33 9.3 Adjacent channel selectivity . 34 9.3.0 Applicability . 34 9.3.1 Definition . 34 9.3.2 Method of measurement . 34 9.3.3 Limits . 35 9.4 Spurious response rejection . 35 9.4.0 Applicability . 35 9.4.1 Definition . 36 9.4.2 Introduction to the method of measurement . 36 9.4.3 Measurement arrangement . 37 9.4.4 Method of the search . 38 9.4.5 Method of measurement . 38 9.4.6 Limits . 39 9.5 Intermodulation response rejection . 39 9.5.0 Applicability . 39 9.5.1 Definition . 39 9.5.2 Method of measurement . 40 9.5.3 Limits . 41 9.6 Blocking or desensitization . 41 SIST EN 300 341 V2.1.1:2016



ETSI ETSI EN 300 341 V2.1.1 (2016-03) 5 9.6.0 Applicability . 41 9.6.1 Definition . 41 9.6.2 Method of measurement . 42 9.6.3 Limits . 43 9.7 Receiver Spurious radiations . 43 9.7.0 Applicability . 43 9.7.1 Definition . 43 9.7.2 Method of measurement . 44 9.7.3 Limits . 45 10 Testing for compliance with technical requirements . 45 10.1 Test conditions, power supply and ambient temperatures . 45 10.2 Interpretation of the measurement results . 46 Annex A (normative): Radiated measurement . 47 A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 47 A.1.0 General . 47 A.1.1 Anechoic chamber . 47 A.1.2 Anechoic chamber with a conductive ground plane . 48 A.1.3 Open Area Test Site (OATS) . 49 A.1.4 Test antenna . 50 A.1.5 Substitution antenna . 50 A.1.6 Measuring antenna . 51 A.2 Guidance on the use of radiation test sites . 51 A.2.0 General . 51 A.2.1 Verification of the test site . 51 A.2.2 Preparation of the EUT . 51 A.2.3 Power supplies to the EUT . 51 A.2.4 Volume control setting for analogue speech tests . 51 A.2.5 Range length . 52 A.2.6 Site preparation . 52 A.3 Coupling of signals . 53 A.3.1 General . 53 A.3.2 Data signals . 53 A.3.3 Speech and analogue signals . 53 A.3.3.0 General . 53 A.3.3.1 Acoustic coupler description. 53 A.3.3.2 Calibration . 53 A.4 Test fixture . 54 A.4.1 Description . 54 A.4.2 Calibration . 54 A.4.3 Mode of use . 55 Annex B (normative): Specification for some particular measurement arrangements . 56 B.1 Power measuring receiver specification . 56 B.1.0 General . 56 B.1.1 IF filter . 56 B.1.2 Attenuation indicator . 58 B.1.3 RMS value indicator . 58 B.1.4 Oscillator and amplifier . 58 B.2 Spectrum analyser specification . 58 B.2.1 Adjacent and alternate channel power measurement . 58 B.2.2 Unwanted emissions measurement . 59 B.3 Integrating and power summing device . 59 Annex C (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 60 History . 62
SIST EN 300 341 V2.1.1:2016



ETSI ETSI EN 300 341 V2.1.1 (2016-03) 6 Intel
...

ETSI EN 300 341 V2.1.1 (2016-03)






HARMONISED EUROPEAN STANDARD
Land Mobile Service;
Radio equipment using an integral antenna transmitting
signals to initiate a specific response in the receiver;
Harmonised Standard covering the essential requirements
of article 3.2 of the Directive 2014/53/EU

---------------------- Page: 1 ----------------------
2 ETSI EN 300 341 V2.1.1 (2016-03)



Reference
REN/ERM-TGDMR-352
Keywords
analogue, mobile, PMR, radio, signalling
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 341 V2.1.1 (2016-03)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 9
4 Speech equipment with signalling . 9
5 General and operational requirements . 10
5.1 General . 10
5.1.1 Environmental profile . 10
5.1.2 Choice of model for testing . 10
6 Test conditions, power sources and ambient temperatures . 10
6.1 Normal and extreme test conditions . 10
6.2 Test power source . 10
6.3 Normal test conditions . 11
6.3.1 Normal temperature and humidity . 11
6.3.2 Normal test power source . 11
6.3.2.1 Mains voltage . 11
6.3.2.2 Regulated lead-acid battery power sources used on vehicles . 11
6.3.2.3 Other power sources . 11
6.4 Extreme test conditions . 11
6.4.1 Extreme temperatures . 11
6.4.2 Extreme test source voltages . 12
6.4.2.1 Mains voltage . 12
6.4.2.2 Regulated lead-acid battery power sources used on vehicles . 12
6.4.2.3 Power sources using other types of batteries . 12
6.4.2.4 Other power sources . 12
6.5 Procedure for tests at extreme temperatures . 12
6.5.0 Thermal Balance. 12
6.5.1 Procedure for equipment designed for continuous operation . 12
6.5.2 Procedure for equipment designed for intermittent operation . 12
7 General conditions of measurement . 13
7.1 Normal test signals, test conditions and the unwanted test signals. 13
7.2 Artificial antenna . 13
7.3 Test sites and general arrangements for radiated measurements . 13
7.4 Transmitter automatic shut-off facility . 13
7.5 Modes of operation of the transmitter . 13
7.6 Arrangements for test signals at the input of the receiver via a test fixture or a test antenna . 14
7.7 Receiver mute or squelch facility . 14
7.8 Encoder for receiver measurements . 14
7.9 Facilities for access between the receiver demodulator output and its decoder . 14
7.10 Calling indicator . 14
7.11 Reset . 14
7.12 Reset time . 14
8 Technical characteristics of the transmitter . 15
8.1 Frequency error . 15
8.1.0 Applicability . 15
8.1.1 Definition . 15
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 341 V2.1.1 (2016-03)
8.1.2 Method of measurement . 15
8.1.3 Limits . 15
8.2 Effective radiated power . 16
8.2.0 Applicability . 16
8.2.1 Definition . 16
8.2.2 Method of measurement . 16
8.2.2.1 Maximum effective radiated power under normal test conditions . 16
8.2.2.2 Average effective radiated power under normal test conditions . 18
8.2.3 Method of measurements of maximum and average effective radiated power under extreme test
conditions . 19
8.2.4 Limits . 19
8.3 Adjacent and alternate channel power . 20
8.3.0 Applicability . 20
8.3.1 Definition . 20
8.3.2 Method of measurement . 20
8.3.3 Limits . 21
8.4 Radiated spurious emissions . 21
8.4.0 Applicability . 21
8.4.1 Definition . 22
8.4.2 Method of measurement . 22
8.4.3 Limits . 24
8.5 Transient frequency behaviour of the transmitter . 24
8.5.0 Applicability . 24
8.5.1 Definitions . 24
8.5.2 Method of measurement . 25
8.5.3 Limits . 28
9 Technical characteristics of the receiver . 28
9.1 Average usable sensitivity (field strength, responses) . 28
9.1.0 Applicability . 28
9.1.1 Definition . 28
9.1.2 Method of measurement under normal test conditions . 28
9.1.3 Method of measurement of the average usable sensitivities under extreme test conditions . 30
9.1.4 References for degradation measurements . 30
9.1.4.1 Definition . 30
9.1.4.2 Procedures for measurements using the test fixture . 31
9.1.4.3 Procedures for measurements using the test site . 31
9.1.5 Limits . 31
9.2 Co-channel rejection . 32
9.2.0 Applicability . 32
9.2.1 Definition . 32
9.2.2 Method of measurement . 32
9.2.3 Limits . 33
9.3 Adjacent channel selectivity . 34
9.3.0 Applicability . 34
9.3.1 Definition . 34
9.3.2 Method of measurement . 34
9.3.3 Limits . 35
9.4 Spurious response rejection . 35
9.4.0 Applicability . 35
9.4.1 Definition . 36
9.4.2 Introduction to the method of measurement . 36
9.4.3 Measurement arrangement . 37
9.4.4 Method of the search . 38
9.4.5 Method of measurement . 38
9.4.6 Limits . 39
9.5 Intermodulation response rejection . 39
9.5.0 Applicability . 39
9.5.1 Definition . 39
9.5.2 Method of measurement . 40
9.5.3 Limits . 41
9.6 Blocking or desensitization . 41
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 341 V2.1.1 (2016-03)
9.6.0 Applicability . 41
9.6.1 Definition . 41
9.6.2 Method of measurement . 42
9.6.3 Limits . 43
9.7 Receiver Spurious radiations . 43
9.7.0 Applicability . 43
9.7.1 Definition . 43
9.7.2 Method of measurement . 44
9.7.3 Limits . 45
10 Testing for compliance with technical requirements . 45
10.1 Test conditions, power supply and ambient temperatures . 45
10.2 Interpretation of the measurement results . 46
Annex A (normative): Radiated measurement . 47
A.1 Test sites and general arrangements for measurements involving the use of radiated fields . 47
A.1.0 General . 47
A.1.1 Anechoic chamber . 47
A.1.2 Anechoic chamber with a conductive ground plane . 48
A.1.3 Open Area Test Site (OATS) . 49
A.1.4 Test antenna . 50
A.1.5 Substitution antenna . 50
A.1.6 Measuring antenna . 51
A.2 Guidance on the use of radiation test sites . 51
A.2.0 General . 51
A.2.1 Verification of the test site . 51
A.2.2 Preparation of the EUT . 51
A.2.3 Power supplies to the EUT . 51
A.2.4 Volume control setting for analogue speech tests . 51
A.2.5 Range length . 52
A.2.6 Site preparation . 52
A.3 Coupling of signals . 53
A.3.1 General . 53
A.3.2 Data signals . 53
A.3.3 Speech and analogue signals . 53
A.3.3.0 General . 53
A.3.3.1 Acoustic coupler description. 53
A.3.3.2 Calibration . 53
A.4 Test fixture . 54
A.4.1 Description . 54
A.4.2 Calibration . 54
A.4.3 Mode of use . 55
Annex B (normative): Specification for some particular measurement arrangements . 56
B.1 Power measuring receiver specification . 56
B.1.0 General . 56
B.1.1 IF filter . 56
B.1.2 Attenuation indicator . 58
B.1.3 RMS value indicator . 58
B.1.4 Oscillator and amplifier . 58
B.2 Spectrum analyser specification . 58
B.2.1 Adjacent and alternate channel power measurement . 58
B.2.2 Unwanted emissions measurement . 59
B.3 Integrating and power summing device . 59
Annex C (normative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 60
History . 62

ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 300 341 V2.1.1 (2016-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPR
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN 300 113 V3.1.1:2020(Main)
Land Mobile Service - Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector
ETSI EN 300 113 V3.1.1 (2020-06)

The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 1 GHz, with channel
separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated
demodulator and decoder.
The types of equipment covered by the present document are as follows:
1) base station (equipment fitted with an antenna connector, intended for use in a fixed location);
2) mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
and
3) those handportable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector , but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
Handportable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.

  • Standard
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    96 pages
    English language
    sale 15% off
  • Standard
    96 pages
    English language
    sale 15% off
  • Draft
    96 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 303 405 V1.1.1:2017(Main)
Land Mobile Service - Analogue and Digital PMR446 Equipment - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 303 405 V1.1.1 (2017-05)

The present document covers the minimum characteristics considered necessary in order to avoid harmful interference
and to make acceptable use of the available frequencies for analogue and digital PMR446 equipment in the land mobile
service.
PMR 446 equipment is hand portable (no base station or repeater use); short range peer to peer mode; uses integral
antennas only; effective radiated power not exceeding 500 mW and angle modulated.
The band from 446,0 MHz to 446,2 MHz is designated for the use of analogue PMR 446 with a channel plan based on
12,5 kHz spacing where the lowest carrier frequency is 446,006 25 MHz.
The band from 446,1 MHz to 446,2 MHz is designated for the use of digital PMR 446 with a channel plan based on
6,25 kHz and 12,5 kHz spacing where the lowest carrier frequencies are 446,103 125 MHz and 446,106 25 MHz
respectively.
The band from 446,0 MHz to 446,2 MHz is designated for the use of digital PMR 446 with a channel plan based on
6,25 kHz and 12,5 kHz spacing where the lowest carrier frequencies are 446,003 125 MHz and 446,006 25 MHz
respectively as of 1 January 2018.
Analogue PMR446 equipment operating in the frequency range from 446,1 MHz to 446,2 MHz uses more robust
receivers as specified in ETSI TS 103 236 [2].
As defined in ECC/DEC/(15)05 [i.6] Analogue PMR446 equipment operating in the frequency range from 446,0 MHz
to 446,1 MHz should use more robust receivers as specified in ETSI TS 103 236 [2] or equivalent technical
specifications when placed on the market as of 1 January 2017.
As defined in ECC/DEC/(15)05 [i.6] all analogue and digitial PMR 446 radio equipment should have reception
capability and equipment having Push-To-Talk (PTT) functionality capable of being latched 'on' should apply a
180 seconds maximum transmitter time-out; equipment having no Push-To-Talk (PTT) functionality should apply a
180 seconds maximum transmitter time-out and VOX (Voice activation exchange) control.
The present document assumes that digital PMR446 equipment using 6,25 kHz channel spacing is compliant with ETSI
TS 102 490 [4].
The present document assumes that digital PMR446 equipment using 12,5 kHz channel spacing is compliant with ETSI
TS 102 361-1 [5].
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio
equipment supports certain features ensuring access to emergency services" [i.7].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.7] may apply to equipment within the scope of the
present document.

  • Standard
    69 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    69 pages
    English language
    sale 15% off
  • Standard
    69 pages
    English language
    sale 15% off
  • Standard
    70 pages
    English language
    sale 15% off
SIST
SIST EN 300 113 V2.2.1:2017(Main)
Land Mobile Service - Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 300 113 V2.2.1 (2016-12)

The present document covers the technical requirements for radio transmitters and receivers used in stations in the
Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 1 GHz, with channel
separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated
demodulator and decoder. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
and
• those handportable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector , but fitted with a permanent internal or a temporary internal 50 Ω
Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input.
Handportable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.2] may apply to equipment within the scope of the
present document.

  • Standard
    98 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    98 pages
    English language
    sale 15% off
  • Standard
    99 pages
    English language
    sale 15% off
SIST
SIST EN 301 166 V2.1.1:2017(Main)
Land mobile service - Radio equipment for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 301 166 V2.1.1 (2016-11)

The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with narrow channel separations (CSP) (less than 10 kHz) and intended for speech and/or data. It is the intention of the present document to cover any Channel Bandwidths (CBW) permitted by National Administrations for such systems, e.g. 6,25 kHz. In the present document different requirements are given for the different radio frequency bands, environmental conditions and types of equipment where appropriate.
In the present document, data transmission systems are defined as systems which transmit and/or receive data and/or digitized voice. The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder.
The present document covers equipment which may use constant envelope or non-constant envelope modulation.
The types of equipment covered by the present document are as follows:
- base station: equipment fitted with antenna connector;
- mobile station: equipment fitted with antenna connector.
Handportable stations:
a) either fitted with an antenna connector; or
b) without an external antenna connector but fitted with a permanent internal or a temporary internal 50 Ω RF connector which allows access to the transmitter output and the receiver input.
Handportable station equipment without an external or internal Radio Frequency (RF) connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document.
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that
"....radio equipment supports certain features ensuring access to emergency services" [i.3].
In addition to the present document, other ENs (e.g. ETSI EN 301 489-1 [i.4] and ETSI EN 301 489-5 [i.5]) that specify technical requirements in respect of essential requirements under the Radio Equipment Directive [i.3], may apply to equipment within the scope of the present document.

  • Standard
    85 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    85 pages
    English language
    sale 15% off
  • Standard
    87 pages
    English language
    sale 15% off
  • Standard
    83 pages
    English language
    sale 15% off
SIST
SIST EN 303 039 V2.1.2:2016(Main)
Land Mobile Service - Multichannel transmitter specification for the PMR Service - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 303 039 V2.1.2 (2016-10)

The present document covers the technical requirements for multiple channel radio transmitters used in stations in the Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel separations of < 10 kHz, 12,5 kHz, 20 kHz, 25 kHz, 50 kHz, 100 kHz and 150 kHz.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech and/or analogue speech and using constant envelope or non-constant envelope modulation.
The equipment comprises a transmitter capable of simultaneous amplification or transmission on two or more RF channels, or an amplifier which when operated with transmitter equipment provides simultaneous transmission on two or more RF channels. The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output; and
• any equipment that may be used in combination with any of the above equipments when directly connected to those equipments for the amplification of the transmitter output signals of two or more individual equipments.
Types of equipment not covered by the present document are as follows:
• hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document;
• any equipment using passive combining solutions where each transmitter connected to the passive combining system transmits on a single channel, as detailed in ETSI EG 200 053 [i.2], clause H.3.
These specifications apply to the transmitter or transmitter amplifier only. If a receiver is fitted to the same equipment, the receiver specifications in the relevant specification (references [i.5] to [i.12]) also apply.
These specifications do not necessarily include all the characteristics that may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable.
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive [i.3] may apply to equipment within the scope of the present document.

  • Standard
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    47 pages
    English language
    sale 15% off
SIST
SIST EN 300 219 V2.1.1:2016(Main)
Land Mobile Service - Radio equipment transmitting signals to initiate a specific response in the receiver - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 300 219 V2.1.1 (2016-08)

The present document applies to constant envelope angle modulation systems for use in the land mobile service, using
the available bandwidth, operating on radio frequencies between 30 MHz and 1 GHz, with channel separations of
12,5 kHz, 20 kHz and 25 kHz intended for transmission and/or reception of signals used to initiate a specific response
in the receiver.The present document applies to non-speech and to the non-speech part of combined speech/non-speech analogue
equipment. In the present document, non-speech radio equipment is defined as a radio equipment transmitting a signal
to initiate a specific response in the receiver. The equipment shall comprise a transmitter and associated encoder and/or
a receiver and associated decoder. The encoder and/or decoder may be a separate piece of equipment, in which case
compliance to the present document covers the encoder and/or decoder in connection with the transmitter and/or
receiver equipment.
In the present document different requirements are given for the different radio frequency bands, channel separations,
environmental conditions and types of equipment, where appropriate.
The types of equipment covered by the present document are as follows:
• Base Station: equipment fitted with an antenna socket;
• Mobile Station: equipment fitted with an antenna socket;
• Handportable stations:
a) fitted with an antenna socket; or
b) without an external antenna socket (integral antenna equipment) but fitted with a permanent internal or a
temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output
and the receiver input.
Handportable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document. Integral antenna equipment is covered by ETSI
EN 300 341 [i.1] (see the corresponding scope).
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio
equipment supports certain features ensuring access to emergency services" [i.5].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the Radio Equipment Directive [i.5] may apply to equipment within the scope of the
present document.

  • Standard
    73 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    73 pages
    English language
    sale 15% off
SIST
SIST EN 302 561 V2.1.1:2016(Main)
Land Mobile Service - Radio equipment using constant or non-constant envelope modulation operating in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 302 561 V2.1.1 (2016-03)

The present document covers the technical requirements for radio transmitters and receivers used in stations and
technical requirements for TMO repeater in the Private Mobile Radio (PMR) service.
It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel
separations of 25 kHz, 50 kHz, 100 kHz and 150 kHz.
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment (base station and mobile station) comprises a transmitter and associated encoder and modulator and/or a
receiver and associated demodulator and decoder.
The types of equipment covered by the present document are as follows:
• base station (equipment fitted with an antenna connector, intended for use in a fixed location);
• mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
• TMO Repeater; and
• those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal
or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter
output and the receiver input.
Hand portable equipment without an external or internal RF connector and without the possibility of having a temporary
internal 50 Ω RF connector is not covered by the present document.
These specifications do not necessarily include all the characteristics which may be required by a user of equipment, nor
do they necessarily represent the optimum performance achievable.
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio
equipment supports certain features ensuring access to emergency services" [i.3].
In addition to the present document, other ENs (e.g. ETSI EN 301 489-1 [i.7] and ETSI EN 301 489-5 [i.8]) that specify
technical requirements in respect of essential requirements under the Radio Equipment Directive [i.3], may apply to
equipment within the scope of the present document.

  • Standard
    67 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    67 pages
    English language
    sale 15% off
  • Standard
    67 pages
    English language
    sale 15% off
SIST
SIST EN 300 296 V2.1.1:2016(Main)
Land Mobile Service - Radio equipment using integral antennas intended primarily for analogue speech - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 300 296 V2.1.1 (2016-03)

The present document covers the minimum characteristics considered necessary in order to avoid harmful interference and to make acceptable use of the available frequencies.
The present document applies to equipment with integral antennas, used in angle modulation systems in the land mobile service, operating on radio frequencies between 30 MHz and 1 000 MHz, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, and is intended primarily for analogue speech.
In the present document different requirements are given for the different radio frequency bands, channel separations, environmental conditions and types of equipment, where appropriate.
The present document is complementary to ETSI EN 300 086 [i.6], which covers radio equipment with an internal or external RF connector, for use in the land mobile service.
The present document may apply to PMR446 equipment as defined in [i.7]. Note that PMR446 equipment has a requirement to incorporate a receiver and may have requirements for 180 s maximum transmission time and VOX.
The present document contains requirements to demonstrate that "... Radio equipment shall be so constructed that it both
effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference" and that "....radio equipment supports certain features ensuring access to emergency services" [i.8].
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the Radio Equipment Directive [i.8] may apply to equipment within the scope of the present document.

  • Standard
    62 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    62 pages
    English language
    sale 15% off
SIST
SIST EN 300 390 V2.1.1:2016(Main)
Land Mobile Service - Radio equipment intended for the transmission of data (and speech) and using an integral antenna - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
ETSI EN 300 390 V2.1.1 (2016-03)

REN/ERM-TGDMR-347

  • Standard
    79 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    79 pages
    English language
    sale 15% off
SIST
SIST EN 302 561 V 1.3.2:2014(Main)
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land Mobile Service - Radio equipment using constant or non-constant envelope modulation operating in a channel bandwidth of 25 kHz, 50 kHz, 100 kHz or 150 kHz - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
ETSI EN 302 561 V1.3.2 (2014-10)

The present document covers the technical requirements for radio transmitters and receivers used in stations and technical requirements for TMO repeater in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies between 30 MHz and 3 GHz, with channel separations of 25 kHz, 50 kHz, 100 kHz and 150 kHz. It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech. The equipment (base station and mobile station) comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The types of equipment covered by the present document are as follows:
-base station (equipment fitted with an antenna connector, intended for use in a fixed location);
-mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable);
-TMO Repeater; and
-those hand portable stations:
a) fitted with an antenna connector; or
b) without an external antenna connector (integral antenna equipment), but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document. These specifications do not necessarily include all the characteristics which may be required by a user of equipment, nor do they necessarily represent the optimum performance achievable. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.4] (R&TTE Directive), which states that "… radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.4] may apply to equipment within the scope of the present document.

  • Standard
    68 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Standard
    68 pages
    English language
    sale 15% off
  • Standard
    68 pages
    English language
    sale 15% off