SIST EN 61300-2-9:2017

SLOVENSKI STANDARD
01-maj-2017
1DGRPHãþD
SIST EN 61300-2-9:2011
SIST EN 61300-2-9:2011/AC:2011
2SWLþQLVSRMQLHOHPHQWLLQSDVLYQHNRPSRQHQWH2VQRYQLSUHVNXVQLLQPHULOQL
SRVWRSNLGHO3UHVNXVLâRN,(&
Fibre optic interconnecting devices and passive components - Basic test and
measurement procedures - Part 2-9: Tests - Shock (IEC 61300-2-9:2017)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Grundlegende Prüf- und
Messverfahren - Teil 2-9: Untersuchungen und Messungen - Schock (IEC 61300-2-
9:2017)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Méthodes
fondamentales d'essais et de mesures - Partie 2-9: Essais - Chocs (IEC 61300-2-
9:2017)
Ta slovenski standard je istoveten z: EN 61300-2-9:2017
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EUROPEAN STANDARD EN 61300-2-9

NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2017
ICS 33.180.20 Supersedes EN 61300-2-9:2010
English Version
Fibre optic interconnecting devices and passive components -
Basic test and measurement procedures - Part 2-9: Tests -
Shock
(IEC 61300-2-9:2017)
Dispositifs d'interconnexion et composants passifs à fibres Lichtwellenleiter - Verbindungselemente und passive
optiques - Méthodes fondamentales d'essais et de mesures Bauelemente - Grundlegende Prüf- und Messverfahren -
- Partie 2-9: Essais - Chocs Teil 2-9: Prüfungen - Schocken
(IEC 61300-2-9:2017) (IEC 61300-2-9:2017)
This European Standard was approved by CENELEC on 2017-02-10. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden,
Switzerland, Turkey and the United Kingdom.

European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2017 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN 61300-2-9:2017 E
European foreword
The text of document 86B/3979/CDV, future edition 3 of IEC 61300-2-9, prepared by SC 86B "Fibre
optic interconnecting devices and passive components" of IEC/TC 86 "Fibre optics" was submitted to
the IEC-CENELEC parallel vote and approved by CENELEC as EN 61300-2-9:2017.
The following dates are fixed:
(dop) 2017-11-10
• latest date by which the document has to be implemented at
national level by publication of an identical national
standard or by endorsement
• latest date by which the national standards conflicting with (dow) 2018-02-10
the document have to be withdrawn

This document supersedes EN 61300-2-9:2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC [and/or CEN] shall not be held responsible for identifying any or all such
patent rights.
Endorsement notice
The text of the International Standard IEC 61300-2-9:2017 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards indicated:
IEC 60068-2-27:2008 NOTE Harmonized as EN 60068-2-27:2009.
IEC 60068-2-47:2005 NOTE Harmonized as EN 60664-1:2007.
IEC 61300-3-3 NOTE Harmonized as EN 61300-3-3.
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated
references, the latest edition of the referenced document (including any amendments) applies.
NOTE 1 When an International Publication has been modified by common modifications, indicated by (mod), the relevant
EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here:
www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-1 -  Environmental testing -- Part 1: General EN 60068-1 -
and guidance
IEC 61300-1 -  Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-3-1 -  Fibre optic interconnecting devices and EN 61300-3-1 -
passive components - Basic test and
measurement procedures -- Part 3-1:
Examinations and measurements - Visual
examination
IEC 61300-3-28 -  Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures -- Part 3-28:
Examinations and measurements -
Transient loss
ISO 2041 -  Mechanical vibration, shock and condition - -
monitoring - Vocabulary
IEC 61300-2-9 ®
Edition 3.0 2017-01
INTERNATIONAL
STANDARD
colour
inside
Fibre optic interconnecting devices and passive components – Basic test and

measurement procedures –
Part 2-9: Tests – Shock
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
ICS 33.180.20 ISBN 978-2-8322-3770-0

– 2 – IEC 61300-2-9:2017 © IEC 2017
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 5
4 General description . 7
5 Apparatus . 7
5.1 Shock machine . 7
5.1.1 General . 7
5.1.2 Repetition rate . 8
5.1.3 Velocity change tolerances . 8
5.1.4 Cross axis motion . 8
5.1.5 Acceleration measuring system . 8
5.2 Mounting fixture . 9
5.3 Optical power measuring equipment . 9
6 Procedure . 9
6.1 Preparation of DUT . 9
6.2 Pre-conditioning . 10
6.3 Initial examinations and measurements . 10
6.4 Testing . 10
6.5 Recovery . 10
6.6 Final examination and measurements . 10
7 Shock severity . 11
8 Details to be specified . 11
Bibliography . 12

Figure 1 – Fixing points . 6
Figure 2 – Pulse shape and limits of tolerance for half-sine pulse . 7
Figure 3 – Frequency characteristics of the overall measuring system without low-pass
filter . 9

Table 1 – Required frequency characteristic values for the overall measuring system . 9
Table 2 – Severity for passive components and modules . 11
Table 3 – Severity for fibre management systems and closures . 11

IEC 61300-2-9:2017 © IEC 2017 – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING
DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES –

Part 2-9: Tests – Shock
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC
Publication(s)"). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61300-2-9 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This third edition cancels and replaces the second edition published in 2010. This edition
constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous
edition:
a) inserted clause "Terms and definitions";
b) added precise descriptions to clause "Apparatus";
c) added sub clause "Testing" into clause "Procedure";
d) added "Bibliography".
– 4 – IEC 61300-2-9:2017 © IEC 2017
The text of this International Standard is based on the following documents:
CDV Report on voting
86B/3979/CDV 86B/4017/RVC
Full information on the voting for the approval of this International Standard can be found in
the report
...