SIST EN 10056-1:2017
(Main)Structural steel equal and unequal leg angles - Part 1: Dimensions
Structural steel equal and unequal leg angles - Part 1: Dimensions
This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainless steel.
Gleichschenklige und ungleichschenklige Winkel aus Stahl - Teil 1: Maße
This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainless steel.
Cornières à ailes égales et inégales en acier de construction - Partie 1 : Dimensions
Diese Europäische Norm legt die Anforderungen an die Nennmaße von warmgewalzten gleichschenkligen und ungleichschenkligen Winkeln fest. Diese Europäische Norm gilt nicht für scharfkantige Winkel. Diese Europäische Norm gilt nicht für gewalzte gleichschenklige und ungleichschenklige Winkel aus nichtrostendem Stahl.
Kotni (L) jekleni profili z enakimi in različnimi kraki - 1. del: Mere
Ta evropski standard določa zahteve za nazivne mere vroče valjanih kotnih profilov z enakimi in različnimi kraki. Ta evropski standard se ne uporablja za kotne profile s kvadratnimi koreni. Te zahteve se ne uporabljajo za enake in različne krake valjanih kotnih profilov iz nerjavnega jekla.
General Information
Relations
Standards Content (Sample)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Gleichschenklige und ungleichschenklige Winkel aus Stahl - Teil 1: MaßeCornières à ailes égales et inégales en acier de construction - Partie 1 : DimensionsStructural steel equal and unequal leg angles - Part 1: Dimensions77.140.70Jekleni profiliSteel profilesICS:Ta slovenski standard je istoveten z:EN 10056-1:2017SIST EN 10056-1:2017en,fr,de01-marec-2017SIST EN 10056-1:2017SLOVENSKI
STANDARDSIST EN 10056-1:20001DGRPHãþD
SIST EN 10056-1:2017
EUROPEAN STANDARD NORME EUROPÉENNE EUROPÄISCHE NORM
EN 10056-1
January
t r s y ICS
y yä s v rä y r Supersedes EN
s r r w xæ sã s { { zEnglish Version
Structural steel equal and unequal leg angles æ Part
sã Dimensions Cornières à ailes égales et inégales en acier de construction æ Partie
sã Dimensions
Gleichschenklige und ungleichschenklige Winkel aus Stahl æ Teil
sã Maße This European Standard was approved by CEN on
s v November
t r s xä
egulations which stipulate the conditions for giving this European Standard the status of a national standard without any alterationä Upætoædate lists and bibliographical references concerning such national standards may be obtained on application to the CENæCENELEC Management Centre or to any CEN memberä
translation under the responsibility of a CEN member into its own language and notified to the CENæCENELEC Management Centre has the same status as the official versionsä
CEN members are the national standards bodies of Austriaá Belgiumá Bulgariaá Croatiaá Cyprusá Czech Republicá Denmarká Estoniaá Finlandá Former Yugoslav Republic of Macedoniaá Franceá Germanyá Greeceá Hungaryá Icelandá Irelandá Italyá Latviaá Lithuaniaá Luxembourgá Maltaá Netherlandsá Norwayá Polandá Portugalá Romaniaá Serbiaá Slovakiaá Sloveniaá Spainá Swedená Switzerlandá Turkey and United Kingdomä
EUROPEAN COMMITTEE FOR STANDARDIZATION COMITÉ EUROPÉEN DE NORMALISATION EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre:
Avenue Marnix 17,
B-1000 Brussels
9
t r s y CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Membersä Refä Noä EN
s r r w xæ sã t r s y ESIST EN 10056-1:2017
EN 10056-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope . 4 2 Normative references . 4 3 Terms and definitions . 4 4 Designation. 4 5 Dimensions . 5 6 Tolerances on shape and dimensions . 5 7 Material . 5 Annex A (informative)
Comparison of symbols used in this document with those in EN 1993-1-1 . 20 Bibliography . 21 SIST EN 10056-1:2017
EN 10056-1:2017 (E) 3 European foreword This document (EN 10056-1:2017) has been prepared by Technical Committee ECISS/TC 103 “Structural steels other than reinforcements”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 10056-1:1998. According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. SIST EN 10056-1:2017
EN 10056-1:2017 (E) 4 1 Scope This European Standard specifies requirements for the nominal dimensions of hot-rolled equal and unequal leg angles. This European Standard does not apply to angles with square roots. These requirements do not apply to equal and unequal leg angles rolled from stainle
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.