SIST EN ISO 6507-3:2006

SLOVENSKI STANDARD
SIST EN ISO 6507-3:2006
01-marec-2006
1DGRPHãþD
SIST EN ISO 6507-3:1998
.RYLQVNLPDWHULDOL±3UHVNXVWUGRWHSR9LFNHUVX±GHO8PHUMDQMHSULPHUMDOQLK
SORãþLF,62
Metallic materials - Vickers hardness test - Part 3: Calibration of reference blocks (ISO
6507-3:2005)
Metallische Werkstoffe - Härteprüfung nach Vickers - Teil 3: Kalibrierung von
Härtevergleichsplatten (ISO 6507-3:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 3: Etalonnage des blocs de
référence (ISO 6507-3:2005)
Ta slovenski standard je istoveten z: EN ISO 6507-3:2005
ICS:
77.040.10 Mehansko preskušanje kovin Mechanical testing of metals
SIST EN ISO 6507-3:2006 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
EN ISO 6507-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
December 2005
ICS 77.040.10 Supersedes EN ISO 6507-3:1997
English Version
Metallic materials - Vickers hardness test - Part 3: Calibration of
reference blocks (ISO 6507-3:2005)
Matériaux métalliques - Essai de dureté Vickers - Partie 3: Metallische Werkstoffe - Härteprüfung nach Vickers - Teil
Etalonnage des blocs de référence (ISO 6507-3:2005) 3: Kalibrierung von Härtevergleichsplatten (ISO 6507-
3:2005)
This European Standard was approved by CEN on 14 December 2005.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the Central Secretariat or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official
versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 6507-3:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN ISO 6507-3:2005 (E)





Foreword


This document (EN ISO 6507-3:2005) has been prepared by Technical Committee ISO/TC 164
"Mechanical testing of metals" in collaboration with Technical Committee ECISS/TC 1 "Steel -
Mechanical testing", the secretariat of which is held by AFNOR.

This European Standard shall be given the status of a national standard, either by publication of
an identical text or by endorsement, at the latest by June 2006, and conflicting national
standards shall be withdrawn at the latest by June 2006.

This document supersedes EN ISO 6507-3:1997.

According to the CEN/CENELEC Internal Regulations, the national standards organizations of
the following countries are bound to implement this European Standard: Austria, Belgium,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary,
Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.


Endorsement notice

The text of ISO 6507-3:2005 has been approved by CEN as EN ISO 6507-3:2005 without any
modifications.

2

---------------------- Page: 3 ----------------------

INTERNATIONAL ISO
STANDARD 6507-3
Third edition
2005-12-15

Metallic materials — Vickers hardness
test —
Part 3:
Calibration of reference blocks
Matériaux métalliques — Essai de dureté Vickers —
Partie 3: Étalonnage des blocs de référence




Reference number
ISO 6507-3:2005(E)
©
ISO 2005

---------------------- Page: 4 ----------------------

ISO 6507-3:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2005 – All rights reserved

---------------------- Page: 5 ----------------------

ISO 6507-3:2005(E)
Contents Page
Foreword. iv
1 Scope . 1
2 Normative references . 1
3 Manufacture of reference blocks . 1
4 Calibration machine. 2
5 Calibration procedure. 4
6 Number of indentations. 4
7 Uniformity of hardness. 4
8 Marking . 5
9 Validity . 5
Annex A (informative) Uncertainty of the mean hardness value of hardness-reference blocks . 6
Bibliography . 9

© ISO 2005 – All rights reserved iii

---------------------- Page: 6 ----------------------

ISO 6507-3:2005(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 6507-3 was prepared by Technical Committee ISO/TC 164, Mechanical testing of metals, Subcommittee
SC 3, Hardness testing.
This third edition cancels and replaces the second edition (ISO 6507-3:1997), which has been technically
revised.
ISO 6507 consists of the following parts, under the general title Metallic materials — Vickers hardness test:
⎯ Part 1: Test method
⎯ Part 2: Verification and calibration of testing machines
⎯ Part 3: Calibration of reference blocks
⎯ Part 4: Tables of hardness values

iv © ISO 2005 – All rights reserved

---------------------- Page: 7 ----------------------

INTERNATIONAL STANDARD ISO 6507-3:2005(E)

Metallic materials — Vickers hardness test —
Part 3:
Calibration of reference blocks
1 Scope
This part of ISO 6507 specifies a method for the calibration of reference blocks to be used for the indirect
verification of Vickers hardness testing machines, as specified in ISO 6507-2.
The method is applicable only for indentations with diagonals W 0,020 mm.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 376:2004, Metallic materials — Calibration of force-proving instruments used for the verification of
uniaxial testing machines
ISO 4287:1997, Geometrical Product Specifications (GPS) — Surface texture: Profile method — Terms,
definitions and surface texture parameters
ISO 6507-1:2005, Metallic materials — Vickers hardness test — Part 1: Test method
ISO 6507-2:2005, Metallic materials — Vickers hardness test — Part 2: Verification and calibration of testing
machines
3 Manufacture of reference blocks
3.1 The block shall be specially manufactured for use as a hardness-reference block.
NOTE Attention is drawn to the need to use a manufacturing process which will give the necessary homogeneity,
stability of structure and uniformity of surface hardness.
3.2 Each metal block to be calibrated shall be of a thickness not less than 5 mm.
3.3 The reference blocks shall be free of magnetism. lt is recommended that the manufacturer shall ensure
that the blocks, if made of steel, have been demagnetized at the end of the manufacturing process.
3.4 The maximum deviation in flatness of the test and support surfaces shall not exceed 0,005 mm. The
maximum error in parallelism shall not exceed 0,010 mm in 50 mm.
3.5 The test surface shall be free from scratches which interfere with the measurement of the indentations.
The surface roughness R shall not exceed 0,000 05 mm for the test surface and 0,000 8 mm for the bottom
a
surface. The sampling length l shall be 0,80 mm (see ISO 4287:1997, 3.1.9).
© ISO 2005 – All rights reserved 1

---------------------- Page: 8 ----------------------

ISO 6507-3:2005(E)
3.6 To verify that no material has been subsequently removed from the reference block, its thickness at the
time of calibration shall be marked on it, to the nearest 0,01 mm, or an identifying mark shall be made on the
test surface [see 8.1
...