SIST EN ISO 10343:2009

SLOVENSKI STANDARD
SIST EN ISO 10343:2009
01-oktober-2009
1DGRPHãþD
SIST EN ISO 10343:2000
2IWDOPLþQLLQVWUXPHQWL2IWDOPRPHWUL,62
Ophthalmic instruments - Ophthalmometers (ISO 10343:2009)
Ophthalmische Instrumente - Ophthalmometer (ISO 10343:2009)
Instruments ophtalmiques - Ophtalmomètres (ISO 10343:2009)
Ta slovenski standard je istoveten z: EN ISO 10343:2009
ICS:
11.040.70 Oftalmološka oprema Ophthalmic equipment
SIST EN ISO 10343:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 10343:2009

---------------------- Page: 2 ----------------------

SIST EN ISO 10343:2009
EUROPEAN STANDARD
EN ISO 10343
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS 11.040.70 Supersedes EN ISO 10343:1999
English Version
Ophthalmic instruments - Ophthalmometers (ISO 10343:2009)
Instruments ophtalmiques - Ophtalmomètres (ISO Ophthalmische Instrumente - Ophthalmometer (ISO
10343:2009) 10343:2009)
This European Standard was approved by CEN on 27 June 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 10343:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 10343:2009
EN ISO 10343:2009 (E)
Contents Page
Foreword .3

2

---------------------- Page: 4 ----------------------

SIST EN ISO 10343:2009
EN ISO 10343:2009 (E)
Foreword
This document (EN ISO 10343:2009) has been prepared by Technical Committee ISO/TC 172 "Optics and
optical instruments" in collaboration with Technical Committee CEN/TC 170 “Ophthalmic optics” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an identical
text or by endorsement, at the latest by January 2010, and conflicting national standards shall be withdrawn at
the latest by January 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 10343:1999.
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following
countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech
Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
Endorsement notice
The text of ISO 10343:2009 has been approved by CEN as a EN ISO 10343:2009 without any modification.

3

---------------------- Page: 5 ----------------------

SIST EN ISO 10343:2009

---------------------- Page: 6 ----------------------

SIST EN ISO 10343:2009

INTERNATIONAL ISO
STANDARD 10343
Second edition
2009-07-01


Ophthalmic instruments —
Ophthalmometers
Instruments ophtalmiques — Ophtalmomètres




Reference number
ISO 10343:2009(E)
©
ISO 2009

---------------------- Page: 7 ----------------------

SIST EN ISO 10343:2009
ISO 10343:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 8 ----------------------

SIST EN ISO 10343:2009
ISO 10343:2009(E)
Foreword

ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 10343 was prepared by Technical Committee ISO/TC 172, Optics and photonics, Subcommittee SC 7,
Ophthalmic optics and instruments.
This second edition cancels and replaces the first edition (ISO 10343:1997), which has undergone minor
revision to update normative references.


© ISO 2009 – All rights reserved iii

---------------------- Page: 9 ----------------------

SIST EN ISO 10343:2009

---------------------- Page: 10 ----------------------

SIST EN ISO 10343:2009
INTERNATIONAL STANDARD ISO 10343:2009(E)

Ophthalmic instruments — Ophthalmometers
1 Scope
This International Standard, together with ISO 15004-1, specifies requirements and test methods for
continuously or digitally indicating ophthalmometers. Certain types of ophthalmometer (designated as code 1
in Table 1) are capable of measuring radii of curvature of contact lenses as described in ISO 18369-3:2006,
4.1. It is assumed that the local corneal front surface and both contact lens surfaces are spherical or toroidal.
This International Standard takes priority over ISO 15004-1, if differences exist.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated r
...