iTeh StandardsiTeh Standards
EURUSD
Your shopping cart is empty.
SIST

SIST ENV 13801:2001

(Main)

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation

This Prestandard gives the recommended practice for installation of thermoplastics piping systems in the field of soil and waste discharge (low and high temperature) inside buildings (marked with "B") and of soil and waste discharge systems for both inside buildings and buried in ground within the building structure (marked with "BD").

Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb der Gebäudestruktur - Thermoplaste - Empfehlungen für die Verlegung

Systemes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux usées ( a basse et a haute température) a l'intérieur de la structure des bâtiments - Thermoplastiques - Pratiques recommandées pour la pose

La présente prénorme donne les pratiques recommandées pour la pose des systemes de canalisations en thermoplastiques dans le domaine de l'évacuation des eaux-vannes et des eaux usées (a basse et a haute température) a l'intérieur des bâtiments (marqués "B") ainsi que des systemes d'évacuation des eaux-vannes et des eaux usées utilisables aussi bien a l'intérieur des bâtiments qu'en enterré a l'intérieur de la structure des bâtiments (marqués "BD").

Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation

General Information

Status
Withdrawn
Publication Date
31-Mar-2001
Withdrawal Date
01-Jun-2014
ICS
23.040.20 - Plastics pipes
91.140.80 - Drainage systems
Technical Committee
PCV - Plastic pipes, fittings and valves
Current Stage
9900 - Withdrawal (Adopted Project)
Start Date
02-Jun-2014
Due Date
25-Jun-2014
Completion Date
02-Jun-2014
Directive
89/106/EEC - Construction products
Mandate
M/BC/CEN/88/15 - Standardization request to CEN/CENELEC in the field of Water supply, drainage and sewerage
Ref Project
ENV 13801:2000 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation

Relations

Replaced By
SIST-TP CEN/TR 13801:2014 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Thermoplastics - Recommended practice for installation
Effective Date
01-Jul-2014
Merged From
PSIST prEN 1451-6:1999 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 6: Recommended practice for installation
Effective Date
08-Mar-2023
Merged From
PSIST prEN 1565-6:1999 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 6: Recommended practice for installation
Effective Date
08-Mar-2023
Parent
PSIST prEN 1451-6:1999 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 6: Recommended practice for installation
Effective Date
22-Dec-2008
Parent
PSIST prEN 1565-6:1999 - Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Styrene copolymer blends (SAN + PVC) - Part 6: Recommended practice for installation
Effective Date
22-Dec-2008

Buy Standard

ENV 13801:2001ENV 13801:2001
PreviousNext
Standardization document
ENV 13801:2001
English language
48 pages
sale 10% off
Preview
sale 10% off
Preview
e-Library read for
1 day

Standards Content (Sample)

SLOVENSKI STANDARD
SIST ENV 13801:2001
01-april-2001
Plastics piping systems for soil and waste discharge (low and high temperature)
within the building structure - Thermoplastics - Recommended practice for
installation
Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Thermoplastics - Recommended practice for installation
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Thermoplaste - Empfehlungen für die
Verlegung
Systemes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées ( a basse et a haute température) a l'intérieur de la structure des bâtiments -
Thermoplastiques - Pratiques recommandées pour la pose
Ta slovenski standard je istoveten z: ENV 13801:2000
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
SIST ENV 13801:2001 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ENV 13801:2001

---------------------- Page: 2 ----------------------

SIST ENV 13801:2001

---------------------- Page: 3 ----------------------

SIST ENV 13801:2001

---------------------- Page: 4 ----------------------

SIST ENV 13801:2001

---------------------- Page: 5 ----------------------

SIST ENV 13801:2001

---------------------- Page: 6 ----------------------

SIST ENV 13801:2001

---------------------- Page: 7 ----------------------

SIST ENV 13801:2001

---------------------- Page: 8 ----------------------

SIST ENV 13801:2001

---------------------- Page: 9 ----------------------

SIST ENV 13801:2001

---------------------- Page: 10 ----------------------

SIST ENV 13801:2001

---------------------- Page: 11 ----------------------

SIST ENV 13801:2001

---------------------- Page: 12 ----------------------

SIST ENV 13801:2001

---------------------- Page: 13 ----------------------

SIST ENV 13801:2001

---------------------- Page: 14 ----------------------

SIST ENV 13801:2001

---------------------- Page: 15 ----------------------

SIST ENV 13801:2001

---------------------- Page: 16 ----------------------

SIST ENV 13801:2001

---------------------- Page: 17 ----------------------

SIST ENV 13801:2001

---------------------- Page: 18 ----------------------

SIST ENV 13801:2001

-------------------
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.

This May Also Interest You

SIST
SIST EN ISO 13266:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of resistance against surface and traffic loading (ISO 13266:2022)
EN ISO 13266:2023

This document specifies a method of testing the resistance of the upper assembly of inspection chambers and manhole components against surface and traffic loading.
It is not applicable to requirements for testing the cover and frame. Those requirements are specified in EN 124-1 or other standards, depending on the material.
NOTE    Upper assembly components normally include shafts or risers, cones, telescopic adapters and near surface components.

  • Standard
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    10 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13268:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics shafts or risers for inspection chambers and manholes - Determination of ring stiffness (ISO 13268:2022)
EN ISO 13268:2023

This document specifies a test method for assessing the initial (short-term) tangential ring stiffness of riser shafts for thermoplastics inspection chambers or manholes.

  • Standard
    16 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    13 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 13267:2023(Main)
Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics inspection chamber and manhole bases - Test methods for buckling resistance (ISO 13267:2022)
EN ISO 13267:2023

This document specifies methods of test for the resistance of the base of thermoplastics inspection chambers and manholes to external soil and ground-water pressure after installation.

  • Standard
    18 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    15 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17176-2:2019+A1:2022(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 2: Pipes
EN 17176-2:2019+A1:2022

This part of FprEN 17176 specifies the characteristics of solid-wall pipes made of oriented unplasticized poly(vinyl chloride) (PVC-O) for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. It also specifies the test parameters for the test methods referred to in this document.
In conjunction with FprEN 17176-1 and FprEN 17176-5, it is applicable to oriented PVC-O pipes with or without integral socket intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)   irrigation under pressure.
It is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar  . The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations.
For temperatures between 25 °C and 45 °C, Figure C.1 of this document applies.
This part of FprEN 17176 specifies a range of pipe sizes and pressure classes and gives a requirement and recommendations concerning colours.
NOTE   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Standard
    30 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 17176-3:2022(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 3: Fittings
CEN/TS 17176-3:2022

This document specifies the characteristics of solid-wall oriented unplasticized poly(vinyl chloride) (PVC-O) fittings for piping systems intended for water supply and for buried drainage, sewerage, treated waste water and irrigation under pressure or above-ground where protected from direct sunlight. The scope of this document is limited to double sockets, repair couplings, reducers and to non-end load bearing elbows.
NOTE 1   The scope of this document is restricted to fittings on the market during the preparation of this document. Therefore, tees, flange adaptors, etc., are excluded from this version of the standard.
NOTE 2   For double sockets, repair couplings and reducers there are no special fittings designs for end-load bearing applications. However, restrained gaskets can be used for end-load bearing applications. In that case, the requirements of EN 17176-5 are applicable.
It also specifies the test parameters for the test methods referred to in this document.
In conjunction with EN 17176-1 and EN 17176-5, this document is applicable to oriented PVC-O fittings intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)   irrigation under pressure.
This document is applicable to piping systems intended for the supply of water with a maximum allowable operating pressure (PFA) up to and including 25 bar ). The piping system according to this document is intended for the conveyance of cold water up to and including 45 °C and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations. For temperatures between 25 °C and 45 °C, EN 17176-2:2019, Figure C.1 applies.
This document specifies a range of fittings sizes and pressure classes and gives a requirement and recommendations concerning colours.
NOTE 3   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN ISO 11296-4:2018/A1:2021(Amendment)
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 4: Lining with cured-in-place pipes - Amendment 1: Updated definitions, marking requirements and procedure for alternative expression of flexural test results (ISO 11296-4:2018/Amd 1:2021)
EN ISO 11296-4:2018/A1:2021

2021-02-11 - TC decision is missing to skip FV.

  • Amendment
    12 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    8 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1329-2:2021(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 2: Guidance for the assessment of conformity
CEN/TS 1329-2:2021

This document gives requirements and guidance for the assessment of conformity of formulations, products and assemblies in accordance with EN 1329 1 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third party certification is involved, the certification body is expected to be compliant with either EN ISO/IEC 17065 [2] or EN ISO/IEC 17021-series [3], as applicable.
NOTE 3   In order to help the reader, a basic test matrix is given in Annex A.
In conjunction with EN 1329 1, this document is applicable to piping systems made of unplasticized poly(vinyl chloride) (PVC U) intended for soil and waste discharge systems (low and high temperature):
-   inside buildings (application area code "B");
-   both inside buildings and buried in ground within the building structure (application area code "BD").

  • Technical specification
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    24 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 1329-1:2021(Main)
Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes, fittings and the system
EN 1329-1:2020

This document specifies the requirements for solid wall pipes with smooth internal and external surfaces, extruded from the same formulation throughout the wall, fittings and the system of unplasticized poly(vinyl chloride) (PVC-U) piping systems intended for soil and waste discharge applications (low and high temperature):
-   inside buildings (application area code "B");
-   for both inside buildings and buried in ground within the building structure (application area code "BD").
NOTE 1   The intended use is reflected in the marking of products by "B" or "BD".
NOTE 2   Multilayer pipes with different formulations throughout the wall and foamed core pipes are covered by EN 1453-1 [1].
NOTE 3   For use buried in ground within the building structure are intended only those components (marked with "BD") with nominal outside diameters equal to or greater than 75 mm.
NOTE 4   EN 476 [2] specifies the general requirements for components used in discharge pipes, drains and sewers for gravity systems. Pipes and fittings conforming to this standard fully meet these requirements.
This document is also applicable to PVC-U pipes, fittings and the system intended for the following purposes:
-   ventilating part of the pipework in association with discharge applications;
-   rainwater pipework within the building structure.
This document also specifies the test parameters for the test method that are referred to.
This document covers a range of nominal sizes, a range of pipes and fittings series and gives recommendations concerning colours.
NOTE 5   It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices or codes.
For external above ground application additional requirements depending on the climate should be agreed between the manufacturer and the user.
NOTE 6   Pipes, fittings and other components conforming to any of the plastics product standards listed in Annex B can be used with pipes and fittings conforming to this document, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements of Table 25.

  • Standard
    46 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    47 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST-TS CEN/TS 1451-2:2020(Main)
Plastic piping systems for soil and waste discharge (low and high temperature) within the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of conformity
CEN/TS 1451-2:2019

This document gives guidance for the assessment of conformity of materials, products, joints and assemblies in accordance with the applicable part(s) of EN 1451 intended to be included in the manufacturer’s quality plan as part of the quality management system and for the establishment of third-party certification procedures.
NOTE 1   The quality management system is expected to conform to or is no less stringent than the relevant requirements to EN ISO 9001 [1].
NOTE 2   If third-party certification is involved, the certification body is expected be accredited to EN ISO/IEC 17065 [2] or EN ISO/IEC 17021 [3], as applicable.
NOTE 3   In order to help the readers, a summary of the test regime is given in Annex A.
In conjunction with EN 1451 1 this document is applicable to piping systems made of polypropylene (PP) intended to be used:
-   for soil and waste discharge systems (low and high temperature) inside buildings (application area code “B”) and,
-   for soil and waste discharge systems (low and high temperature) for both inside buildings and buried in ground within the building structure (application area code “BD”)
This is reflected in the marking of products by “B” or “BD”.

  • Technical specification
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
  • Draft
    22 pages
    English language
    sale 10% off
    e-Library read for
    1 day
SIST
SIST EN 17176-1:2019(Main)
Plastics piping systems for water supply and for buried and above ground drainage, sewerage and irrigation under pressure - Oriented unplasticized poly(vinyl chloride) (PVC-O) - Part 1: General
EN 17176-1:2019

This part of prEN 17176 specifies the general aspects of oriented unplasticized poly(vinyl chloride) (PVC-O), for solid wall piping systems intended for water supply, pressurized sewer systems and irrigation systems to be used underground or above-ground where protected to direct sunlight.
In conjunction with prEN 17176-2, prEN 17176-3, EN ISO 1452 4, it is applicable to PVC-O pipes, PVC-O fittings, and valves, their joints and to joints with components of other plastics and non-plastics materials intended to be used for the following:
a)   water mains and services lines;
b)   conveyance of water for both outside and inside buildings;
c)   drainage, sewerage and treated waste water under pressure;
d)    Irrigation under pressure.
It is applicable to piping systems intended for the supply of water under pressure up to and including 25 °C (cold water), intended for human consumption and for general purposes as well as for waste water under pressure.
This part of prEN 17176 is also applicable to components for the conveyance of water and waste water up to and including 45 °C. For temperatures between 25 °C and 45 °C, prEN 17176-2:2017, Figure C.1 applies.
The piping system according to this European Standard is intended for the conveyance of cold water up to pressures of 25 bars and especially in those applications where special performance requirements are needed, such as impact loads and pressure fluctuations, up to pressure of 25 bars.

  • Standard
    14 pages
    English language
    sale 10% off
    e-Library read for
    1 day