SIST EN 301 908-15 V4.2.1:2010

ETSI EN 301 908-15 V4.2.1 (2010-03)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 15: Harmonized EN for IMT-2000,
Evolved Universal Terrestrial Radio Access (E-UTRA)
(FDD Repeaters) covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 301 908-15 V4.2.1 (2010-03)



Reference
DEN/ERM-TFES-002-15
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2010.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 301 908-15 V4.2.1 (2010-03)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 15
4.2.2.3 Conformance . 15
4.2.3 Spurious emissions . 15
4.2.3.1 Definition . 15
4.2.3.2 Limit . 16
4.2.3.2.1 Spurious emissions . 16
4.2.3.2.2 Co-existence with other systems in the same geographical area . 16
4.2.3.3 Conformance . 17
4.2.4 Maximum output power . 18
4.2.4.1 Definition . 18
4.2.4.2 Limit . 18
4.2.4.3 Conformance . 18
4.2.5 Input intermodulation . 18
4.2.5.1 Definition . 18
4.2.5.2 Limit . 19
4.2.5.2.1 General input intermodulation requirement . 19
4.2.5.2.2 Co-existence with other systems . 19
4.2.5.3 Conformance . 20
4.2.6 Out of band gain . 20
4.2.6.1 Definition . 20
4.2.6.2 Limits . 20
4.2.6.3 Conformance . 20
4.2.7 Adjacent Channel Rejection Ratio . 21
4.2.7.1 Definition . 21
4.2.7.2 Limit . 21
4.2.7.2.1 ACRR . 21
4.2.7.2.2 Co-existence with UTRA . 21
4.2.7.3 Conformance . 21
4.2.8 Output intermodulation . 21
4.2.8.1 Definition . 21
4.2.8.2 Limit . 22
4.2.8.3 Conformance . 22
5 Testing for compliance with technical requirements . 22
5.1 Environmental conditions for testing . 22
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 301 908-15 V4.2.1 (2010-03)
5.2 Interpretation of the measurement results . 22
5.3 Essential radio test suites . 24
5.3.1 Operating band unwanted emissions . 24
5.3.1.1 Initial conditions . 24
5.3.1.2 Procedures . 24
5.3.2 Spurious emissions . 25
5.3.2.1 Initial conditions . 25
5.3.2.2 Procedures . 25
5.3.3 Maximum output power . 26
5.3.3.1 Initial conditions . 26
5.3.3.2 Procedures . 26
5.3.4 Input intermodulation . 26
5.3.4.1 Initial conditions . 26
5.3.4.2 Procedures . 27
5.3.5 Out of band gain . 27
5.3.5.1 Initial conditions . 27
5.3.5.2 Procedures . 27
5.3.6 Adjacent Channel Rejection Ratio . 27
5.3.6.1 Initial conditions . 27
5.3.6.2 Procedures . 28
5.3.7 Output intermodulation . 28
5.3.7.1 Initial conditions . 28
5.3.7.2 Procedures . 28
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 30
Annex B (normative): Repeater configurations . 32
B.1 Power supply . 32
B.2 Power supply options . 32
B.3 Combining of Repeaters . 32
Annex C (normative): Repeater stimulus signal spectral purity requirements . 33
Annex D (informative): Environmental profile specification . 34
Annex E (informative): The EN title in the official languages . 35
Annex F (informative): Bibliography . 36
History . 37

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 301 908-15 V4.2.1 (2010-03)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 15 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 301 908-15 V4.2.1 (2010-03)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 19 February 2010
Date of latest announcement of this EN (doa): 31 May 2010
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 30 November 2010
Date of withdrawal of any conflicting National Standard (dow): 30 November 2011

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 301 908-15 V4.2.1 (2010-03)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
These radio equipment types are capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz

The present document covers requirements for E-UTRA Repeaters for Release 8.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 301 908-15 V4.2.1 (2010-03)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] ETSI TS 136 143 (V8.2.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD
repeater conformance testing (3GPP TS 36.143 version 8.2.0 Release 8)".
[3] Void.
[4] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] ETSI EN 301 908-11 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation
cellular networks; Part 11: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD
and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[8] ETSI TS 136 141 (V8.4.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base
Station (BS) conformance testing (3GPP TS 36.141 version 8.4.0 Release 8)".
[9] ETSI TS 125 141 (V8.8.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 8.8.0 Release 8)".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
[i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 301 908-15 V4.2.1 (2010-03)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge: lowest and highest frequency of the pass band of the repeater
operating band: frequency range in which E-UTRA FDD operates, that is defined with a specific set of technical
requirements
NOTE 1: The operating band(s) for an E-UTRA Repeater is declared by the manufacturer according to the
designations in clause 1, table 1-1.
NOTE 2: Unless specified, operating band refers to the uplink operating band and downlink operating band.
output power, Pout: mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to
the nominal load impedance of the transmitter
pass band: repeater can have one or several pass bands
NOTE: The pass band is the frequency range that the repeater operates in with operational configuration. This
frequency range can correspond to one or several consecutive nominal channels. If they are not
consecutive each subset of channels is considered as an individual pass band.
rated output power: rated output power of the repeater is the mean power level per carrier that the manufacturer has
declared to be available at the antenna connector
repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink
direction (from the Base Station to the mobile area) and in the uplink direction (from the mobile to the Base St
...

Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE)
for IMT-2000 Third-Generation cellular networks;
Part 15: Harmonized EN for IMT-2000,
Evolved Universal Terrestrial Radio Access (E-UTRA)
(FDD Repeaters) covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)



Reference
DEN/ERM-TFES-002-15
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
Contents
Intellectual Property Rights . 5
Foreword . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 8
2.2 Informative references . 8
3 Definitions, symbols and abbreviations . 9
3.1 Definitions . 9
3.2 Symbols . 10
3.3 Abbreviations . 10
4 Technical requirements specifications . 11
4.1 Environmental profile . 11
4.2 Conformance requirements . 11
4.2.1 Introduction. 11
4.2.2 Operating band unwanted emissions . 11
4.2.2.1 Definition . 11
4.2.2.2 Limit . 12
4.2.2.2.1 General operating band unwanted emissions . 12
4.2.2.2.2 Protection of the BS receiver in the operating band . 15
4.2.2.3 Conformance . 15
4.2.3 Spurious emissions . 15
4.2.3.1 Definition . 15
4.2.3.2 Limit . 16
4.2.3.2.1 Spurious emissions . 16
4.2.3.2.2 Co-existence with other systems in the same geographical area . 16
4.2.3.3 Conformance . 17
4.2.4 Maximum output power . 18
4.2.4.1 Definition . 18
4.2.4.2 Limit . 18
4.2.4.3 Conformance . 18
4.2.5 Input intermodulation . 18
4.2.5.1 Definition . 18
4.2.5.2 Limit . 19
4.2.5.2.1 General input intermodulation requirement . 19
4.2.5.2.2 Co-existence with other systems . 19
4.2.5.3 Conformance . 20
4.2.6 Out of band gain . 20
4.2.6.1 Definition . 20
4.2.6.2 Limits . 20
4.2.6.3 Conformance . 20
4.2.7 Adjacent Channel Rejection Ratio . 21
4.2.7.1 Definition . 21
4.2.7.2 Limit . 21
4.2.7.2.1 ACRR . 21
4.2.7.2.2 Co-existence with UTRA . 21
4.2.7.3 Conformance . 21
4.2.8 Output intermodulation . 21
4.2.8.1 Definition . 21
4.2.8.2 Limit . 22
4.2.8.3 Conformance . 22
5 Testing for compliance with technical requirements . 22
5.1 Environmental conditions for testing . 22
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
5.2 Interpretation of the measurement results . 22
5.3 Essential radio test suites . 24
5.3.1 Operating band unwanted emissions . 24
5.3.1.1 Initial conditions . 24
5.3.1.2 Procedures . 24
5.3.2 Spurious emissions . 25
5.3.2.1 Initial conditions . 25
5.3.2.2 Procedures . 25
5.3.3 Maximum output power . 26
5.3.3.1 Initial conditions . 26
5.3.3.2 Procedures . 26
5.3.4 Input intermodulation . 26
5.3.4.1 Initial conditions . 26
5.3.4.2 Procedures . 27
5.3.5 Out of band gain . 27
5.3.5.1 Initial conditions . 27
5.3.5.2 Procedures . 27
5.3.6 Adjacent Channel Rejection Ratio . 27
5.3.6.1 Initial conditions . 27
5.3.6.2 Procedures . 28
5.3.7 Output intermodulation . 28
5.3.7.1 Initial conditions . 28
5.3.7.2 Procedures . 28
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 30
Annex B (normative): Repeater configurations . 32
B.1 Power supply . 32
B.2 Power supply options . 32
B.3 Combining of Repeaters . 32
Annex C (normative): Repeater stimulus signal spectral purity requirements . 33
Annex D (informative): Environmental profile specification . 34
Annex E (informative): The EN title in the official languages . 35
Annex F (informative): Bibliography . 36
History . 37

ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 15 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The
modular structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 6 ----------------------
7 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
These radio equipment types are capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz

The present document covers requirements for E-UTRA Repeaters for Release 8.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 7 ----------------------
8 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] ETSI TS 136 143 (V8.2.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD
repeater conformance testing (3GPP TS 36.143 version 8.2.0 Release 8)".
[3] Void.
[4] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] ETSI EN 301 908-11 (V4.1.2): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation
cellular networks; Part 11: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD
and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[8] ETSI TS 136 141 (V8.4.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base
Station (BS) conformance testing (3GPP TS 36.141 version 8.4.0 Release 8)".
[9] ETSI TS 125 141 (V8.8.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 8.8.0 Release 8)".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
[i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
[i.5] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
ETSI

---------------------- Page: 8 ----------------------
9 Final draft ETSI EN 301 908-15 V4.1.2 (2009-12)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor Base Station
downlink: signal path where Base Station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
nominal passband edge: lowest and highest frequency of the pass band of the repeater
operating band: frequency range in which E-UTRA FDD operates, that is defined with a specific set of technical
requirements
NOTE 1: The operating band(s) for an E-UTRA Repeater is declared by the manufacturer according to the
designations in clause 1, table 1-1.
NOTE 2: Unless specified, operating band refers to the uplink operating band and downlink operating band.
output power, Pout: mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to
the nominal load impedance of the transmitter
pass band: repeater can have one or several pass bands
NOTE: The pass band is the frequency range that the repeater operates in with operational configuration. This
frequency range can correspond to one or several consecutive nominal channels. If they are not
consecutive each subset of channels is considered as an individual pass band.
rated output power: rated output power of the repeater is the mean power level per carrier that the manufacturer has
declared to be available at the antenna connector
repeater: device that receives,
...

Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
Harmonized European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for
IMT-2000 Third-Generation cellular networks;
Part 15: Harmonized EN for IMT-2000,
Evolved Universal Terrestrial Radio Access (E-UTRA)
(FDD Repeaters) covering the essential requirements of
article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)



Reference
DEN/ERM-TFES-002-15
Keywords
3G, 3GPP, cellular, digital, IMT-2000, mobile,
radio, regulation, repeater, UMTS, WCDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2009.
All rights reserved.

TM TM TM TM
DECT , PLUGTESTS , UMTS , TIPHON , the TIPHON logo and the ETSI logo are Trade Marks of ETSI registered
for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
LTE™ is a Trade Mark of ETSI currently being registered
for the benefit of its Members and of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .6
1 Scope.7
2 References.7
2.1 Normative references.8
2.2 Informative references.8
3 Definitions, symbols and abbreviations .9
3.1 Definitions.9
3.2 Symbols.10
3.3 Abbreviations.10
4 Technical requirements specifications .10
4.1 Environmental profile.10
4.2 Conformance requirements.11
4.2.1 Introduction.11
4.2.2 Operating band unwanted emissions .11
4.2.2.1 Definition.11
4.2.2.2 Limit.11
4.2.2.2.1 General operating band unwanted emissions.12
4.2.2.2.2 Protection of the BS receiver in the operating band .13
4.2.2.3 Conformance.14
4.2.3 Spurious emissions.14
4.2.3.1 Definition.14
4.2.3.2 Limit.14
4.2.3.2.1 Spurious emissions.14
4.2.3.2.2 Co-existence with other systems in the same geographical area .14
4.2.3.3 Conformance.16
4.2.4 Maximum output power.16
4.2.4.1 Definition.16
4.2.4.2 Limit.16
4.2.4.3 Conformance.16
4.2.5 Input intermodulation.16
4.2.5.1 Definition.16
4.2.5.2 Limit.17
4.2.5.2.1 General input intermodulation requirement.17
4.2.5.2.2 Co-existence with other systems .18
4.2.5.3 Conformance.18
4.2.6 Out of band gain .18
4.2.6.1 Definition.18
4.2.6.2 Limits.19
4.2.6.3 Conformance.19
4.2.7 Adjacent Channel Rejection Ratio.19
4.2.7.1 Definition.19
4.2.7.2 Limit.19
4.2.7.2.1 ACRR.19
4.2.7.2.1 Co-existence with UTRA.19
4.2.7.3 Conformance.20
4.2.8 Output intermodulation.20
4.2.8.1 Definition.20
4.2.8.2 Limit.20
4.2.8.3 Conformance.20
5 Testing for compliance with technical requirements.21
5.1 Environmental conditions for testing .21
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
5.2 Interpretation of the measurement results .21
5.3 Essential radio test suites.22
5.3.1 Operating band unwanted emissions .22
5.3.1.1 Initial conditions .22
5.3.1.2 Procedures.22
5.3.2 Spurious emissions.23
5.3.2.1 Initial conditions .23
5.3.2.2 Procedures.23
5.3.3 Maximum output power.24
5.3.3.1 Initial conditions .24
5.3.3.2 Procedures.24
5.3.4 Input intermodulation.25
5.3.4.1 Initial conditions .25
5.3.4.2 Procedures.25
5.3.5 Out of band gain .25
5.3.5.1 Initial conditions .25
5.3.5.2 Procedures.26
5.3.6 Adjacent Channel Rejection Ratio.26
5.3.6.1 Initial conditions .26
5.3.6.2 Procedures.26
5.3.7 Output intermodulation.27
5.3.7.1 Initial conditions .27
5.3.7.2 Procedures.27
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT).28
Annex B (normative): Repeater configurations .30
B.1 Power supply.30
B.2 Power supply options .30
B.3 Combining of Repeaters.30
Annex C (informative): Environmental profile specification .31
Annex D (informative): The EN title in the official languages .32
Annex E (informative): Bibliography.33
History .34

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Public Enquiry phase
of the ETSI standards Two-step Approval Procedure.
The present document has been produced by ETSI in response to a mandate from the European Commission issued
under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the
field of technical standards and regulations.
The present document is intended to become a Harmonized Standard, the reference of which will be published in the
Official Journal of the European Communities referencing the Directive 1999/5/EC [i.2] of the European Parliament
and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual
recognition of their conformity ("the R&TTE Directive").
Technical specifications relevant to Directive 1999/5/EC [i.2] are given in annex A.
The present document is part 15 of a multi-part deliverable covering the Base Stations (BS), Repeaters and User
Equipment (UE) for IMT-2000 Third-Generation cellular networks, as identified below:
Part 1: "Harmonized EN for IMT-2000, introduction and common requirements, covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 2: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 3: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 4: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 5: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) and Evolved CDMA Multi-Carrier
Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE
Directive";
Part 6: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (UE) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 7: "Harmonized EN for IMT-2000, CDMA TDD (UTRA TDD and E-UTRA TDD) (BS) covering the
essential requirements of article 3.2 of the R&TTE Directive";
Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements
of article 3.2 of the R&TTE Directive";
Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements
of article 3.2 of the R&TTE Directive";
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of
the R&TTE Directive";
Part 11: "Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD and E-UTRA FDD) (Repeaters)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential
requirements of article 3.2 of the R&TTE Directive";
Part 13: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (UE) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 14: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (BS) covering
the essential requirements of article 3.2 of the R&TTE Directive";
Part 15: "Harmonized EN for IMT-2000, Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD
Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE)
covering the essential requirements of article 3.2 of the R&TTE Directive";
Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS)
covering the essential requirements of article 3.2 of the R&TTE Directive".

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive. The modular
structure is shown in EG 201 399 [i.3].
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
1 Scope
The present document applies to the following radio equipment types:
• Repeaters for Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD).
These radio equipment types are capable of operating in all or any part of the operating bands given in table 1-1.
Table 1-1: E-UTRA Repeater operating bands
E-UTRA FDD Direction of transmission E-UTRA Repeater operating bands
band
1 Downlink 2 110 MHz to 2 170 MHz
Uplink 1 920 MHz to 1 980 MHz
3 Downlink 1 805 MHz to 1 880 MHz
Uplink 1 710 MHz to 1 785 MHz
7 Downlink 2 620 MHz to 2 690 MHz
Uplink 2 500 MHz to 2 570 MHz
8 Downlink 925 MHz to 960 MHz
Uplink 880 MHz to 915 MHz

The present document covers requirements for E-UTRA Repeaters for Release 8.
The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive), Article 3.2,
which states that "…. radio equipment shall be so constructed that it effectively uses the spectrum allocated to
terrestrial/space radio communications and orbital resources so as to avoid harmful interference".
In addition to the present document, other ENs that specify technical requirements in respect of essential requirements
under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present
document.
NOTE: A list of such ENs is included on the web site http://www.newapproach.org.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• Non-specific reference may be made only to a complete document or a part thereof and only in the following
cases:
- if it is accepted that it will be possible to use all future changes of the referenced document for the
purposes of the referring document;
- for informative references.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
2.1 Normative references
The following referenced documents are indispensable for the application of the present document. For dated
references, only the edition cited applies. For non-specific references, the latest edition of the referenced document
(including any amendments) applies.
[1] ETSI EN 301 908-1 (V4.1.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular
networks; Part 1: Harmonized EN for IMT-2000, introduction and common requirements,
covering the essential requirements of article 3.2 of the R&TTE Directive".
[2] ETSI TS 136 143 (V8.0.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA);
Repeater conformance testing (3GPP TS 36.143 version 8.0.0 Release 8)".
[3] ETSI TR 100 028 (all parts) (V1.4.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Uncertainties in the measurement of mobile radio equipment characteristics".
[4] ITU-R Recommendation SM.329-10 (2003): "Unwanted emissions in the spurious domain".
[5] IEC 60068-2-1 (2007): "Environmental testing - Part 2-1: Tests - Test A: Cold".
[6] IEC 60068-2-2 (2007): "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[7] ETSI EN 301 908-11 (V4.1.1): "Electromagnetic compatibility and Radio spectrum Matters
(ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation
cellular networks; Part 11: Harmonized EN for IMT-2000, CDMA Direct Spread (UTRA FDD
and E-UTRA FDD) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE
Directive".
[8] ETSI TS 136 141 (V8.1.0): "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base
Station (BS) conformance testing (3GPP TS 36.141 version 8.1.0 Release 8)".
[9] ETSI TS 125 141 (V8.6.0): "Universal Mobile Telecommunications System (UMTS); Base
Station (BS) conformance testing (FDD) (3GPP TS 25.141 version 8.6.0 Release 8)".
2.2 Informative references
The following referenced documents are not essential to the use of the present document but they assist the user with
regard to a particular subject area. For non-specific references, the latest version of the referenced document (including
any amendments) applies.
[i.1] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a
procedure for the provision of information in the field of technical standards and regulations.
[i.2] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.3] ETSI EG 201 399: "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to
the production of candidate Harmonized Standards for application under the R&TTE Directive".
[i.4] ETSI TR 102 215 (V1.3.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Recommended approach, and possible limits for measurement uncertainty for the measurement of
radiated electromagnetic fields above 1 GHz".
ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 301 908-15 V4.1.1 (2009-04)
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
carrier: modulated waveform conveying the E-UTRA or UTRA (WCDMA) physical channels
channel bandwidth: RF bandwidth supporting a single E-UTRA RF carrier with the transmission bandwidth
configured in the uplink or downlink of a cell
NOTE: The channel bandwidth is measured in MHz and is used as a reference for transmitter and receiver RF
requirements.
channel edge: lowest and highest frequency of the E-UTRA carrier, separated by the channel bandwidth
donor coupling loss: coupling loss between the repeater and the donor base station
downlink: signal path where base station transmits and mobile receives
downlink operating band: part of the operating band designated for downlink
operating band: frequency range in which E-UTRA FDD operates, that is defined with a specific set of technical
requirements
NOTE 1: The operating band(s) for an E-UTRA Repeater is declared by the manufacturer according to the
designations in clause 1, table 1-1.
NOTE 2: Unless specified, operating band refers to the uplink operating band and downlink operating band.
output power, Pout: mean power of one carrier at maximum repeater gain delivered to a load with resistance equal to
the nominal load impedance of the transmitter
pass band: repeater can have one or several pass bands
NOTE: The pass band is the frequency range that the repeater operates in with operational configuration. This
frequency range can correspond to one or several consecutive nominal channels. If they are not
consecutive each subset of channels shall be considered as an individual pass band.
rated output power: rated output power of the repeater is the mean power level per carrier that the manufacturer has
declared to be available at the antenna connector
repeater: device that receives, amplifies and transmits the radiated or conducted RF carrier both in the downlink
direction (from the base station to the mobile area) and in the uplink direction (from the mobile to the base station)
transmission bandwidth: bandwidth of an instantaneous transmission from a UE or BS, measured in Resource Block
units
transmission bandwidth configuration: highest transmission bandwidth
...