Passenger car tyres and rims — Part 2: Rims

Pneumatiques et jantes pour voitures particulières — Partie 2: Jantes

General Information

Status
Withdrawn
Publication Date
26-Sep-2001
Withdrawal Date
26-Sep-2001
Current Stage
9599 - Withdrawal of International Standard
Completion Date
07-Jun-2007
Ref Project

Relations

Buy Standard

Standard
ISO 4000-2:2001 - Passenger car tyres and rims
English language
5 pages
sale 15% off
Preview
sale 15% off
Preview
Standard
ISO 4000-2:2001 - Pneumatiques et jantes pour voitures particulieres
French language
5 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 4000-2
Third edition
2001-09-15
Passenger car tyres and rims —
Part 2:
Rims
Pneumatiques et jantes pour voitures particulières —
Partie 2: Jantes
Reference number
ISO 4000-2:2001(E)
©
ISO 2001

---------------------- Page: 1 ----------------------
ISO 4000-2:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2001
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Printed in Switzerland
ii © ISO 2001 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 4000-2:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 4000 may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 4000-2 was prepared by Technical Committee ISO/TC 31, Tyres, rims and valves,
Subcommittee SC 3, Passenger car tyres and rims.
This third edition cancels and replaces the second edition (ISO 4000-2:1994), which has been technically revised.
ISO 4000 consists of the following parts, under the general title Passenger car tyres and rims:
— Part 1: Tyres (metric series)
— Part 2: Rims
© ISO 2001 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 4000-2:2001(E)
Passenger car tyres and rims —
Part 2:
Rims
1 Scope
This part of ISO 4000 specifies the designation, contour and dimensions of 5° tapered (drop-centre) rims primarily
intended for passenger cars.
2 Normative reference
The following normative document contains provisions which, through reference in this text, constitute provisions of
this part of ISO 4000. For dated references, subsequent amendments to, or revisions of, any of these publications
do not apply. However, parties to agreements based on this part of ISO 4000 are encouraged to investigate the
possibility of applying the most recent edition of the normative document indicated below. For undated references,
the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of
currently valid International Standards.
ISO 3911, Wheels and rims for pneumatic tyres — Vocabulary, designation and marking
3 Terms and definitions
For the purposes of this part of ISO 4000, the terms and definitions given in ISO 3911 apply.
4 Designation and marking
The rim shall be designated
...

NORME ISO
INTERNATIONALE 4000-2
Troisième édition
2001-09-15
Pneumatiques et jantes pour voitures
particulières —
Partie 2:
Jantes
Passenger car tyres and rims —
Part 2: Rims
Numéro de référence
ISO 4000-2:2001(F)
©
ISO 2001

---------------------- Page: 1 ----------------------
ISO 4000-2:2001(F)
PDF – Exonération de responsabilité
Le présent fichier PDF peut contenir des polices de caractères intégrées. Conformément aux conditions de licence d'Adobe, ce fichier peut
être imprimé ou visualisé, mais ne doit pas être modifiéà moins que l'ordinateur employéà cet effet ne bénéficie d'une licence autorisant
l'utilisation de ces polices et que celles-ci y soient installées. Lors du téléchargement de ce fichier, les parties concernées acceptent de fait la
responsabilité de ne pas enfreindre les conditions de licence d'Adobe. Le Secrétariat central de l'ISO décline toute responsabilité en la
matière.
Adobe est une marque déposée d'Adobe Systems Incorporated.
Les détails relatifs aux produits logiciels utilisés pour la créationduprésent fichier PDF sont disponibles dans la rubrique General Info du
fichier; les paramètres de création PDF ont été optimisés pour l'impression. Toutes les mesures ont été prises pour garantir l'exploitation de
ce fichier par les comités membres de l'ISO. Dans le cas peu probable où surviendrait un problème d'utilisation, veuillez en informer le
Secrétariat central à l'adresse donnée ci-dessous.
© ISO 2001
Droits de reproduction réservés. Sauf prescription différente, aucune partie de cette publication ne peut être reproduite ni utilisée sous quelque
forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et les microfilms, sans l'accord écrit de l’ISO à
l’adresse ci-aprèsouducomité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 56 � CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax. + 41 22 749 09 47
E-mail copyright@iso.ch
Web www.iso.ch
Imprimé en Suisse
ii © ISO 2001 – Tous droits réservés

---------------------- Page: 2 ----------------------
ISO 4000-2:2001(F)
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux de
normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général confiéeaux
comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire partie du comité
technique créé à cet effet. Les organisations internationales, gouvernementales et non gouvernementales, en
liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec la Commission
électrotechnique internationale (CEI) en ce qui concerne la normalisation électrotechnique.
Les Normes internationales sont rédigées conformément aux règles données dans les Directives ISO/CEI,
Partie 3.
Les projets de Normes internationales adoptés par les comités techniques sont soumis aux comités membres pour
vote. Leur publication comme Normes internationales requiert l'approbation de 75 % au moins des comités
membres votants.
L’attention est appelée sur le fait que certains des éléments delaprésente partie de l’ISO 4000 peuvent faire
l’objet de droits de propriété intellectuelle ou de droits analogues. L’ISO ne saurait être tenue pour responsable de
ne pas avoir identifié de tels droits de propriété et averti de leur existence.
La Norme internationale ISO 4000-2 a étéélaboréepar le comité technique ISO/TC 31, Pneus, jantes et valves,
sous-comité SC 3, Pneus et jantes de voitures particulières.
Cette troisième édition annule et remplace la deuxième édition (ISO 4000-2:1994), dont elle constitue une révision
technique.
L'ISO 4000 comprend les parties suivantes, présentées sous le titre général Pneumatiques et jantes pour voitures
particulières:
— Partie 1: Pneumatiques (série millimétrique)
— Partie 2: Jantes
© ISO 2001 – Tous droits réservés iii

---------------------- Page: 3 ----------------------
NORME INTERNATIONALE ISO 4000-2:2001(F)
Pneumatiques et jantes pour voitures particulières —
Partie 2:
Jantes
1 Domaine d'application
La présente partiedel'ISO4000spécifie la désignation, le profil et les cotes des jantes (à base creuse) coniques à
5° principalement destinées aux voitures particulières.
2Référence normative
Le document normatif suivant contient des dispositions qui, par suite de la référence qui y est faite, constituent des
dispositions valables pour la présente partie de l'ISO 4000. Pour les références datées, les amendements
ultérieurs ou les révisions de ces publications ne s’appliquent pas. Toutefois, les parties prenantes aux accords
fondés sur la présente partie de l'ISO 4000 sont invitées à rechercher la possibilité d'appliquer l’édition la plus
récente du document normatif indiqué ci-après. Pour les références non datées, la dernière édition du document
normatif en référence s’applique. Les membres de l'ISO et de la CEI possèdent le registre des Normes
internationales en vigueur.
ISO 3911, Roues et jantes pour pneumatiques — Vocabulaire, désignation et marquage
3 Termes et définitions
Pour les besoins de la présente partie de l'ISO 4000, les termes et définitions donnés dans l'ISO 3911 s'appliquent.
4Désignation et marquage
La jante doit être désignée par son code de diamètre nominal, son code de largeur nominale et le type de son
rebord (par exemple 15� 6 J ou 13� 5.50 B).
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.