ISO 7001:2007/Amd 4:2017

INTERNATIONAL ISO
STANDARD 7001
Third edition
2007-11-01
AMENDMENT 4
2017-05
Graphical symbols — Public
information symbols
AMENDMENT 4
Symboles graphiques — Symboles destinés à l’information du public
AMENDEMENT 4
Reference number
ISO 7001:2007/Amd.4:2017(E)
©
ISO 2017

---------------------- Page: 1 ----------------------
ISO 7001:2007/Amd.4:2017(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2017, Published in Switzerland
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form
or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior
written permission. Permission can be requested from either ISO at the address below or ISO’s member body in the country of
the requester.
ISO copyright office
Ch. de Blandonnet 8 • CP 401
CH-1214 Vernier, Geneva, Switzerland
Tel. +41 22 749 01 11
Fax +41 22 749 09 47
copyright@iso.org
www.iso.org
ii © ISO 2017 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 7001:2007/Amd.4:2017(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/ directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www .iso .org/ patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation on the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO’s adherence to the
World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT) see the following
URL: w w w . i s o .org/ iso/ foreword .html
This document was prepared by Technical Committee ISO/TC 145, Graphical symbols, Subcommittee
SC 1, Public information symbols.
© ISO 2017 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 7001:2007/Amd.4:2017(E)
Graphical symbols — Public information symbols
AMENDMENT 4
Add the following public information symbols to the alphabetical summary in Table 1 and to the
summary of all symbols in Tables 2 and 7:
— PI TF 042: Meeting point
— PI TF 043: Tour group meeting point
— PI PF 074: Automatic sensor faucet or tap
— PI PF 075: Hand dryer
— PI PF 076: Toilet paper
© ISO 2017 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 7001:2007/Amd.4:2017(E)

PI TF 042: Meeting point
Reference no.
ISO 7001 – PI TF 042
Meaning
Meeting point
Function
To indicate a designated place for people to meet.
Image content
Side view of two standing human figures shaking hands
with one figure holding a briefcase.
Human behaviour that is intended to be caused after understanding the public information symbol’s meaning
Finding a meeting place.
Need
To indicate a designated place to meet.
Related meanings
PI TF 043.
Field of application
Signs at stations, airports and in towns.
Public facilities, transport facilities.
Context of use
Intended user population
General population.
Age of user
Any.
Additional information
Test data obtained according to ISO 9186-1 are available from more than one country. Findings from testing
showed that the symbol did not reach the criteria of acceptability. Consequently, it is recommended that this
symbol is accompanied by text to increate comprehension.
2 © ISO 2017 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 7001:2007/Amd.4:2017(E)

PI TF 043: Tour group meeting point
Reference
...