ISO 9073-5:2025
(Main)Nonwovens — Test methods — Part 5: Determination of resistance to mechanical penetration (ball burst procedure)
Nonwovens — Test methods — Part 5: Determination of resistance to mechanical penetration (ball burst procedure)
This document specifies a method for determining the resistance to mechanical penetration of nonwoven fabrics by a ball of a given diameter. The method is primarily designed to be used on nonwovens with some degree of elasticity, for which a regular burst test does not apply.
Nontissés — Méthodes d’essai — Partie 5: Détermination de la résistance à la pénétration mécanique (méthode d’éclatement à la bille)
Le présent document spécifie une méthode de détermination de la résistance à la pénétration mécanique des étoffes non tissées par une bille d’un diamètre donné. Cette méthode est essentiellement destinée à être utilisée sur des nontissés ayant un certain degré d’élasticité, pour lesquels un essai d’éclatement normal ne s’applique pas.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 9073-5
Second edition
Nonwovens — Test methods —
2025-04
Part 5:
Determination of resistance to
mechanical penetration (ball burst
procedure)
Nontissés — Méthodes d’essai —
Partie 5: Détermination de la résistance à la pénétration
mécanique (méthode d’éclatement à la bille)
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Principle . 2
5 Apparatus . 2
6 Sampling . 3
6.1 General .3
6.2 Lot size .3
6.3 Sampling .3
7 Conditioning . 4
8 Procedure . 4
9 Test report . 5
Annex A (informative) General information regarding precision. 6
Annex B (informative) General information regarding causes for low precision when ball burst
testing . 7
Bibliography . 8
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 38, Textiles, in collaboration with the European
Committee for Standardization (CEN) Technical Committee CEN/TC 248, Textiles and textile products, in
accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 9073-5:2008), which has been technically
revised.
The main changes are as follows:
— the title has been changed from "Textiles — Test methods for nonwovens — Part 5: Determination of
resistance to mechanical penetration (ball burst procedure)” to "Nonwovens — Test methods — Part 5
Determination of resistance to mechanical penetration (ball burst procedure)”;
— Clause 1, the scope has been corrected;
— Clause 2, the normative references have been updated;
— a sentence regarding to SI values has been added in Clause 7.
A list of all parts in the ISO 9073 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
International Standard ISO 9073-5:2025(en)
Nonwovens — Test methods —
Part 5:
Determination of resistance to mechanical penetration (ball
burst procedure)
1 Scope
This document specifies a method for determining the resistance to mechanical penetration of nonwoven
fabrics by a ball of a given diameter.
The method is primarily designed to be used on nonwovens with some degree of elasticity, for which a
regular burst test does not apply.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 139, Textiles — Standard atmospheres for conditioning and testing
ISO 186, Paper and board — Sampling to determine average quality
ISO 9092, Nonwovens — Vocabulary
ISO 10012:2003, Measurement management systems — Requirements for measurement processes and
measuring equipment
3 Terms and definitions
For the purposes of this document, the terms and definitions given in ISO 9092 and the following apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
nonwoven fabric
fabric made directly from a web of fibres, without the yarn preparation necessary for weaving and knitting
3.2
constant-rate-of-traverse (CRT) tensile-testing machine
testing machine in which the moving clamp moves at a uniform rate
3.3
bursting force
force or pressure required to rupture a textile by distending it with a force, applied at right angles to the
plane of the fabric, under specified conditions
4 Principle
A test specimen of nonwoven is clamped horizontally under tension between two grooved, ring-shaped
plates in the position of the lower, fixed, clamp of a constant-rate-of-traverse (CRT) tensile-testing machine
(see Figure 1). A force is exerted vertically downwards against the test specimen by a polished hardened-
steel ball that is attached in the position of the upper, movable, clamp. The test is terminated when the ball
ruptures the material.
5 Apparatus
5.1 Constant-rate-of-traverse (CRT) tensile-testing machine, converted for use in the compression
mode and fitted with a ball burst attachment (5.2) replacing the two clamp assemblies (see Figure 1).
5.2 Ball burst attachment, consisting of
a) a polished steel ball (5.3) that replaces the upper, moving, clamp of the tensile-testing machine;
b) a ring-clamp mechanism (5.4) that replaces the lower, fixed, clamp of the tensile-testing machine.
5.3 Polished steel ball, having a diameter of (25,400 ± 0,005) mm and spherical to within 0,005 mm.
The size of the ball may differ from that stated if so agreed upon by all interested parties and recorded in the
test report.
5.4 Ring clamp, having an internal diameter of (44,500 ± 0,025) mm.
The size of the ring clamp may differ from that stated if agreed upon by all interested parties, and recorded
in the test report.
Figure 1 — Apparatus
6 Sampling
6.1 General
Carry out sampling in accordance with ISO 186. Ensuring that the areas from which samples are taken, have
no visible flaws and are not creased.
6.2 Lot size
A lot should be established based on a logical break in the process or as prescribed by a regulation or
traceability requirements.
Test specimens being selected in accordance with NWSP 005.0, if applicable.
6.3 Sampling
Take random sample as directed in the customer specifications. If no requirements are provided, ISO 2859-1
or ISO 3951-1 can be used. Three samples should be taken for this test. In and of themselves, these are not
valid sampling plans by default. An agreement between the purchaser and supplier requires considering
process stability, producer’s risk, consumer’s risk, acceptable quality level and the cost needs to be
established.
In general, if the test characteristic can be considered normally distributed, the sampling procedures for
inspection by variables will require fewer samples. However, small samples may not reflect that normal
distribution and the estimated percent defective can therefore be over or underestimated. In this case, as
well as for attribute data, the sampling procedures for inspection by attributes should be used.
In the absence of any sampling size requirement, Table 1 and Table 2 can be used. Switching rules are
required to maintain the AQL protection.
Table 1 — Attributes (1.0 AQL, General Inspection Level II)
Number of units in the lot inclusive Number of units that comprise the lot sample
1 to 150 13
151 to 280 32
281 to 500 50
501 to 1 200 80
Table 2 — Variables (“s” method, General Inspection Level II)
Number of units in the lot inclusive Number of units that comprise the lot sample
1 to 15 3
16 to 25 4
26 to 50 6
51 to 90 9
91 to 150 13
151 to 280 18
281 to 500 25
501 to 1 200 35
NOTE An adequate specification or other agreement between the purchaser and supplier requires considering
the variability between rolls of nonwoven fabric and between test specimens from a swatch from a roll of material
to provide a sampling plan with meaningful producer’s risk, consumer’s risk, acceptable quality level, and limiting
quality level.
7 Conditioning
Bring samples to moisture equilibrium in the standard atmosphere for testing nonwovens as directed in
ISO 139. Equilibrium is considered to have been reached when the increase in mass of the test specimen
in successive weighing made at intervals of not less than 2 h does not exceed 0,25 % of the mass of the test
specimen.
NOTE While conditioning for a fixed time cannot be accepted in cases of dispute, it may be sufficient in routine
testing to expose the material to the standard atmosphere for testing textiles for a reasonable period of time before
the test specimens are tested, i.e. 4 h.
8 Procedure
8.1 Each test specimen shall be at least 125 mm square or a circle at least 125 mm in diameter. Test
specimens need not be cut for testing. Take
...
PROJET FINAL
Norme
internationale
ISO/FDIS 9073-5
ISO/TC 38
Nontissés — Méthodes d’essai —
Secrétariat: JISC
Partie 5:
Début de vote:
2025-01-27
Détermination de la résistance à la
pénétration mécanique (méthode
Vote clos le:
2025-03-24
d’éclatement à la bille)
Nonwovens — Test methods —
Part 5: Determination of resistance to mechanical penetration
(ball burst procedure)
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
NORMES POUVANT
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
Numéro de référence
ISO/FDIS 9073-5:2025(fr) © ISO 2025
PROJET FINAL
ISO/FDIS 9073-5:2025(fr)
Norme
internationale
ISO/FDIS 9073-5
ISO/TC 38
Nontissés — Méthodes d’essai —
Secrétariat: JISC
Partie 5:
Début de vote:
Détermination de la résistance à la 2025-01-27
pénétration mécanique (méthode
Vote clos le:
2025-03-24
d’éclatement à la bille)
Nonwovens — Test methods —
Part 5: Determination of resistance to mechanical penetration
(ball burst procedure)
LES DESTINATAIRES DU PRÉSENT PROJET SONT
INVITÉS À PRÉSENTER, AVEC LEURS OBSERVATIONS,
NOTIFICATION DES DROITS DE PROPRIÉTÉ DONT ILS
AURAIENT ÉVENTUELLEMENT CONNAISSANCE ET À
FOURNIR UNE DOCUMENTATION EXPLICATIVE.
DOCUMENT PROTÉGÉ PAR COPYRIGHT
OUTRE LE FAIT D’ÊTRE EXAMINÉS POUR
ÉTABLIR S’ILS SONT ACCEPTABLES À DES FINS
© ISO 2025 INDUSTRIELLES, TECHNOLOGIQUES ET COM-MERCIALES,
AINSI QUE DU POINT DE VUE DES UTILISATEURS, LES
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
PROJETS DE NORMES
TRAITEMENT PARALLÈLE ISO/CEN
INTERNATIONALES DOIVENT PARFOIS ÊTRE CONSIDÉRÉS
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
DU POINT DE VUE DE LEUR POSSI BILITÉ DE DEVENIR DES
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
NORMES POUVANT
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
SERVIR DE RÉFÉRENCE DANS LA RÉGLEMENTATION
NATIONALE.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse Numéro de référence
ISO/FDIS 9073-5:2025(fr) © ISO 2025
ii
ISO/FDIS 9073-5:2025(fr)
Sommaire Page
Avant-propos .iv
1 Domaine d’application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Principe. 2
5 Appareillage . 2
6 Échantillonnage . 3
6.1 Généralités .3
6.2 Taille du lot . .3
6.3 Échantillonnage .3
7 Conditionnement . 4
8 Mode opératoire . 4
9 Rapport d’essai . 5
Annexe A (informative) Informations générales concernant la fidélité . 7
Annexe B (informative) Informations générales sur les causes d’une faible fidélité lors
des essais d’éclatement à la bille . 8
Bibliographie . 9
iii
ISO/FDIS 9073-5:2025(fr)
Avant-propos
L’ISO (Organisation internationale de normalisation) est une fédération mondiale d’organismes nationaux
de normalisation (comités membres de l’ISO). L’élaboration des Normes internationales est en général
confiée aux comités techniques de l’ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l’ISO participent également aux travaux. L’ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d’approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de tout
droit de propriété revendiqué à cet égard. À la date de publication du présent document, l’ISO n’avait pas reçu
notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois, il y a lieu
d’avertir les responsables de la mise en application du présent document que des informations plus récentes
sont susceptibles de figurer dans la base de données de brevets, disponible à l’adresse www.iso.org/brevets.
L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié de tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l’ISO liés à l’évaluation de la conformité, ou pour toute information au sujet de l’adhésion de
l’ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 38, Textiles, en collaboration avec le
comité technique CEN/TC 248, Textiles et produits textiles, du Comité européen de normalisation (CEN),
conformément à l’Accord de coopération technique entre l’ISO et le CEN (Accord de Vienne).
Cette deuxième édition annule et remplace la première édition (ISO 9073-5:2008), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes:
— le titre a été modifié, «Textiles — Méthodes d’essai pour nontissés — Partie 5: Détermination de la résistance
à la pénétration mécanique (méthode d’éclatement à la bille)» a été remplacé par «Nontissés — Méthodes
d’essai — Partie 5: Détermination de la résistance à la pénétration mécanique (méthode d’éclatement à la
bille)»;
— à l’Article 1, le domaine d’application a été corrigé;
— à l’Article 2, les références normatives ont été mises à jour;
— une phrase relative aux valeurs SI a été ajoutée à l’Article 7.
Une liste de toutes les parties de la série ISO 9073 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.
iv
PROJET FINAL Norme internationale ISO/FDIS 9073-5:2025(fr)
Nontissés — Méthodes d’essai —
Partie 5:
Détermination de la résistance à la pénétration mécanique
(méthode d’éclatement à la bille)
1 Domaine d’application
Le présent document spécifie une méthode de détermination de la résistance à la pénétration mécanique
des étoffes non tissées par une bille d’un diamètre donné.
Cette méthode est essentiellement destinée à être utilisée sur des nontissés ayant un certain degré
d’élasticité, pour lesquels un essai d’éclatement normal ne s’applique pas.
2 Références normatives
Les documents ci-après sont des références normatives indispensables à l’application du présent document.
Pour les références datées, seule l’édition citée s’applique. Pour les références non datées, la dernière édition
du document de référence s’applique (y compris les éventuels amendements).
ISO 139, Textiles — Atmosphères normales de conditionnement et d'essai
ISO 186, Papier et carton — Échantillonnage pour déterminer la qualité moyenne
ISO 9092, Nontissés — Vocabulaire
ISO 10012:2003, Systèmes de management de la mesure — Exigences pour les processus et les équipements
de mesure
3 Termes et définitions
Pour les besoins du présent document, les termes et les définitions de l’ISO 9092 ainsi que les suivants
s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse https:// www .electropedia .org/
3.1
étoffe non tissée
étoffe fabriquée directement à partir d’un voile de fibres, sans passer par la préparation des fils requise
dans le cas de tissage et de tricotage
3.2
machine d’essai de traction à vitesse constante d’allongement (CRE)
machine d’essai sur laquelle la mâchoire de traction se déplace à une vitesse uniforme
ISO/FDIS 9073-5:2025(fr)
3.3
force d’éclatement
force ou pression exigée pour rompre un textile en l’étirant avec une force appliquée perpendiculairement
au plan de l’étoffe, dans des conditions spécifiées
4 Principe
Une éprouvette de nontissé est maintenue horizontalement sous tension entre deux plaques circulaires
rainurées au niveau du mors inférieur, fixe de la machine d’essai de traction à vitesse constante d’allongement
(CRE) (voir Figure 1). Une force est exercée verticalement vers le bas contre l’éprouvette au moyen d’une bille
en acier trempé poli qui est fixée sur le mors mobile supérieur. L’essai est terminé lorsque la bille provoque
la rupture du matériau.
5 Appareillage
5.1 Machine d’essai de traction à vitesse constante d’allongement (CRE), adaptée pour une utilisation
en compression, munie d’un dispositif d’éclatement à la bille (5.2) qui remplace l’ensemble des mors de
serrage (voir la Figure 1).
5.2 Dispositif d’éclatement à la bille, constitué:
a) d’une bille d’acier poli (5.3) qui remplace le mors mobile supérieur de la machine de traction;
b) d’un mécanisme annulaire de serrage (5.4) qui remplace le mors fixe inférieur de la machine de traction.
5.3 Bille d’acier poli, d’un diamètre de (25,400 ± 0,005) mm et de forme sphérique à 0,005 mm près.
Les dimensions de la bille peuvent différer de celles indiquées. Si tel est le cas, elles doivent faire l’objet d’un
accord entre l’ensemble des parties intéressées et être consignées dans le rapport d’essai.
5.4 Pince (de serrage) annulaire, d’un diamètre intérieur de (44,500 ± 0,025) mm.
Les dimensions de la pince annulaire peuvent différer de celles indiquées si toutes les parties intéressées
sont d’accord. Elles doivent être consignées dans le rapport d’essai.
ISO/FDIS 9073-5:2025(fr)
Figure 1 — Appareillage
6 Échantillonnage
6.1 Généralités
Procéder à l’échantillonnage conformément à l’ISO 186, en veillant à ce que les surfaces de prélèvement
soient exemptes de défauts visibles et de plis.
6.2 Taille du lot
Il convient qu’un lot soit établi sur la base d’une rupture logique dans le processus ou tel que prescrit par une
réglementatio
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.