Crosslinked polyethylene (PE-X) and crosslinked medium density polyethylene (PE-MDX) — Effect of time and temperature on expected strength

This document specifies the minimum values for expected strength as a function of time and temperature in the form of reference lines, for use in calculations on crosslinked polyethylene (PE-X) pipes and crosslinked medium density polyethylene (PE-MDX) pipes. NOTE 1 This document is applicable for pipes with the minimum level of crosslinking after production in accordance with Clause 4. NOTE 2 The density range for medium density polyethylene is 926 kg/m3 to 940 kg/m3 in accordance with ISO 17855-1:2014[2].

Tubes en polyéthylène réticulé (PE-X et PE-MDX) — Influence du temps et de la température sur la résistance espérée

General Information

Status
Published
Publication Date
25-Feb-2019
Current Stage
9060 - Close of review
Start Date
02-Sep-2029
Ref Project

Relations

Buy Standard

Standard
ISO 10146:2019 - Crosslinked polyethylene (PE-X) and crosslinked medium density polyethylene (PE-MDX) -- Effect of time and temperature on expected strength
English language
11 pages
sale 15% off
Preview
sale 15% off
Preview

Standards Content (Sample)

INTERNATIONAL ISO
STANDARD 10146
Second edition
2019-03
Crosslinked polyethylene (PE-X)
and crosslinked medium density
polyethylene (PE-MDX) — Effect of
time and temperature on expected
strength
Tubes en polyéthylène réticulé (PE-X et PE-MDX) — Influence du
temps et de la température sur la résistance espérée
Reference number
ISO 10146:2019(E)
©
ISO 2019

---------------------- Page: 1 ----------------------
ISO 10146:2019(E)

COPYRIGHT PROTECTED DOCUMENT
© ISO 2019
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2019 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 10146:2019(E)

Contents Page
Foreword .iv
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Characteristics . 2
5 Basic formulae . 2
6 Expected strength . 3
6.1 Extrapolation limits . 3
6.2 Graphical representation . 4
6.3 Tabulated values . 4
Annex A (normative) Demonstrating conformance of pipes to the reference lines .10
Bibliography .11
© ISO 2019 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO 10146:2019(E)

Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www .iso .org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subjec
...

Questions, Comments and Discussion

Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.