ISO 24631-1:2025
(Main)Radiofrequency identification of animals — Part 1: Evaluation of conformance of RFID transponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code)
Radiofrequency identification of animals — Part 1: Evaluation of conformance of RFID transponders with ISO 11784 and ISO 11785 (including granting and use of a manufacturer code)
This document provides the means of evaluating the conformance with ISO 11784 and ISO 11785 of radiofrequency identification (RFID) transponders used in the individual identification of animals. It sets forth the conditions for the granting and use of the manufacturer code related to a transponder and the associated rights and obligations of the parties involved in the issuance of the code.
Identification des animaux par radiofréquence — Partie 1: Évaluation de la conformité des transpondeurs RFID à l'ISO 11784 et à l'ISO 11785 (y compris l'attribution et l'utilisation d'un code de fabricant)
Le présent document fournit les moyens d’évaluer la conformité à l’ISO 11784 et à l’ISO 11785 des transpondeurs RFID (identification par radiofréquence) utilisés pour l’identification individuelle des animaux. Il établit les conditions d’attribution et d’utilisation du code de fabricant associé à un transpondeur, ainsi que les droits et devoirs des parties impliquées concernant l’attribution du code.
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 24631-1
Third edition
Radiofrequency identification of
2025-02
animals —
Part 1:
Evaluation of conformance of RFID
transponders with ISO 11784 and
ISO 11785 (including granting and
use of a manufacturer code)
Identification des animaux par radiofréquence —
Partie 1: Évaluation de la conformité des transpondeurs RFID
à l'ISO 11784 et à l'ISO 11785 (y compris l'attribution et
l'utilisation d'un code de fabricant)
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Abbreviated terms . 4
5 Conformance . 4
6 Application . 4
7 Test procedures . 6
7.1 General .6
7.2 Full test (category A) .6
7.3 Limited test (category B) .7
7.4 Listing update procedure (category C) .7
7.5 Test apparatus.7
7.6 Test conditions .8
Annex A (normative) Test application form (ISO 24631-1) . 9
Annex B (normative) Conditions for using ISO 11784 coding (ISO 24631-1).10
Annex C (normative) Manufacturer code application form (ISO 24631-1) .11
Bibliography .12
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and
forestry, Subcommittee SC 19, Agricultural electronics.
This third edition cancels and replaces the second edition (ISO 24631-1:2017), which has been technically
revised.
The main changes are as follows:
— Annexes C, E and F of the previous edition have been moved to ISO 11784, and subsequent annexes have
been renumbered.
A list of all parts in the ISO 24631 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
ISO has appointed a registration authority (RA) competent to register manufacturer codes used in the
radiofrequency identification (RFID) of animals in accordance with ISO 11784 and ISO 11785 (see ISO 11784).
This document deals with the conformance of RFID transponders, of which the main types used for animal
identification are
— injectable transponders,
— electronic ear tag transponders,
— electronic ruminal bolus transponders,
— leg tag transponders, and
— tag attachments.
The test procedures specified in this document are recognized by the Federation of European Companion
Animals Veterinary Association (FECAVA) and World Small Animal Veterinarian Association (WSAVA) and,
as such, can also be applied to companion animals.
v
International Standard ISO 24631-1:2025(en)
Radiofrequency identification of animals —
Part 1:
Evaluation of conformance of RFID transponders with ISO
11784 and ISO 11785 (including granting and use of a
manufacturer code)
1 Scope
This document provides the means of evaluating the conformance with ISO 11784 and ISO 11785 of
radiofrequency identification (RFID) transponders used in the individual identification of animals. It sets
forth the conditions for the granting and use of the manufacturer code related to a transponder and the
associated rights and obligations of the parties involved in the issuance of the code.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 11784, Radio frequency identification of animals — Code structure
ISO 11785:1996, Radio frequency identification of animals — Technical concept
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminological databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
activation field
electromagnetic field with a frequency of 134,2 kHz
3.2
country code
three-digit numeric code representing a country in accordance with ISO 3166-1
3.3
identification code
code used to identify the animal individually, at the national and, in combination with a country code (3.2),
international levels
Note 1 to entry: It is a national responsibility to ensure the uniqueness of national ID codes.
3.4
laboratory reference transceiver
transceiver used to test the transponders generating the activation field (3.1), able to read FDX-B and HDX
transponders
3.5
manufacturer
company that submits an application for conformance testing or for the granting and use of a manufacturer
code (3.8) for transponders in conformance with ISO 11784 and ISO 11785 while accepting the conditions
set forth in Annex B, ISO 11784:2024, Annex B or ISO 11784:2024, Annex C
Note 1 to entry: see also ISO 11784:2024, Annex A
3.6
manufacturer code
MFC
three-digit number granted by the RA (3.13) to a manufacturer (3.5) under the conditions set forth in
ISO 11784:2024, Annex C, whose range and placement within the code structure are in accordance with
ISO 11784
Note 1 to entry: Only one manufacturer code is granted to the same manufacturer.
3.7
primary transponder packaging
primary protective layer of transponder components
3.8
product code
six-digit number granted (and registered) by the registration authority (3.13) to a manufacturer (3.5) for a
certain type of transponder, formatted such that its first part is the manufacturer code (3.6) and its second
part is a three-digit serial number
3.9
purchaser
person, organization or company that receives legal ownership of equipment by a transaction involving that
equipment
3.10
RA-recognized test centre
test centre meeting the criteria of the registration authority (3.13)
3.11
RA-registered transponder
transponder registered by the registration authority (3.13)
3.12
RA-registered manufacturer
manufacturer (3.5) with one or more RA-registered transponders (3.11)
3.13
registration authority
RA
entity that approves test laboratories and issues and registers manufacturer (3.5) and product codes (3.8)
3.14
retagging
process that assigns to a new transponder the same identification number as a transponder (3.19) that has
been lost or that is no longer readable
3.15
retagging counter
three-bit field for counting the number of retagging (3.14)
3.16
shared manufacturer code
three-digit number granted by the registration authority (3.13) to a manufacturer (3.5) according to
ISO 11784:2024, Annex C
Note 1 to entry: A shared manufacturer code can be granted to more than one manufacturer.
3.17
secondary transponder packaging
additional layers to primary transponder packaging (3.7)
3.18
transceiver
device used to communicate with the transponder (3.19)
3.19
transponder
radiofrequency identification (RFID) device that transmits its stored information when activated by a
transceiver (3.18) and that may be able to store new information
Note 1 to entry: A transponder can be characterized according to its components (chip, coil, capacitor, etc.),
communication protocol, size, shape and packaging, or any additional characteristics that could change its properties.
The main types are defined in 3.19.1 to 3.19.5.
3.19.1
injectable transponder
small transponder (3.19) encapsulated in a biocompatible material with porosity equivalent to that of glass
able to be injected into an animal’s body
3.19.2
electronic ear tag transponder
plastic-covered transponder (3.19) able to be fixed to the ear of the animal using a locking mechanism or to
be attached to an ear tag such that it cannot be removed from the tag without damaging it
3.19.3
electronic ruminal bolus transponder
transponder (3.19) placed into a high specific gravity container able to be orally administered to a ruminant,
which remains permanently in its fore stomach
3.19.4
tag attachment
transponder components covered by a prim
...
Norme
internationale
ISO 24631-1
Troisième édition
Identification des animaux par
2025-02
radiofréquence —
Partie 1:
Évaluation de la conformité
des transpondeurs RFID à l'ISO
11784 et à l'ISO 11785 (y compris
l'attribution et l'utilisation d'un
code de fabricant)
Radiofrequency identification of animals —
Part 1: Evaluation of conformance of RFID transponders with
ISO 11784 and ISO 11785 (including granting and use of a
manufacturer code)
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application .1
2 Références normatives .1
3 Termes et définitions .1
4 Termes abrégés .4
5 Conformité .4
6 Demande .4
7 Modes opératoires d’essai . 6
7.1 Généralités .6
7.2 Essai complet (catégorie A) .6
7.3 Essai limité (catégorie B) . .7
7.4 Mise à jour de la liste (catégorie C) .7
7.5 Appareillage d’essai.7
7.6 Conditions d’essai . . .8
Annexe A (normative) Formulaire de demande d’essai (ISO 24631-1) .9
Annexe B (normative) Conditions relatives à l’utilisation des codes ISO 11784 (ISO 24631-1) .10
Annexe C (normative) Formulaire de demande d’un code de fabricant (ISO 24631-1) .11
Bibliographie .12
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document a
été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2 (voir
www.iso.org/directives).
L’ISO attire l’attention sur le fait que la mise en application du présent document peut entraîner l’utilisation
d’un ou de plusieurs brevets. L’ISO ne prend pas position quant à la preuve, à la validité et à l’applicabilité de
tout droit de brevet revendiqué à cet égard. À la date de publication du présent document, l’ISO n'avait pas
reçu notification qu’un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d’avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse
www.iso.org/brevets. L’ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de propriété.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l’intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l’Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 23, Tracteurs et matériels agricoles et
forestiers, sous-comité SC 19, Électronique en agriculture.
Cette troisième édition annule et remplace la deuxième édition (ISO 24631-1:2017), qui a fait l’objet d’une
révision technique.
Les principales modifications sont les suivantes :
— Les Annexes C, E et F de l'édition précédente ont été déplacées vers l'ISO 11784, et les annexes restantes
ont été renumérotées.
Une liste de toutes les parties de la série ISO 24631 se trouve sur le site web de l’ISO.
Il convient que l’utilisateur adresse tout retour d’information ou toute question concernant le présent
document à l’organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l’adresse www.iso.org/fr/members.html.
iv
Introduction
L’ISO a désigné un organisme d’enregistrement (RA, registration authority) ayant la compétence d’enregistrer
les codes de fabricant utilisés dans l’identification par radiofréquence (RFID) des animaux, conformément à
l’ISO 11784 et à l’ISO 11785 (voir ISO 11784).
Le présent document traite de la conformité des transpondeurs RFID, dont les principaux types utilisés pour
l’identification des animaux sont :
— les transpondeurs injectables ;
— les marques auriculaires électroniques ;
— les bolus ruminaux ;
— les bagues de paturon électroniques ; et
— les supports de transpondeur.
Les modes opératoires d’essai spécifiés dans le présent document sont reconnus par la Fédération
européenne des associations vétérinaires pour les animaux de compagnie (FECAVA) et par l’Association
mondiale vétérinaire pour les petits animaux (WSAVA), et peuvent donc s’appliquer également aux animaux
de compagnie.
v
Norme internationale ISO 24631-1:2025(fr)
Identification des animaux par radiofréquence —
Partie 1:
Évaluation de la conformité des transpondeurs RFID à l'ISO
11784 et à l'ISO 11785 (y compris l'attribution et l'utilisation
d'un code de fabricant)
1 Domaine d'application
Le présent document fournit les moyens d’évaluer la conformité à l’ISO 11784 et à l’ISO 11785 des
transpondeurs RFID (identification par radiofréquence) utilisés pour l’identification individuelle des
animaux. Il établit les conditions d’attribution et d’utilisation du code de fabricant associé à un transpondeur,
ainsi que les droits et devoirs des parties impliquées concernant l’attribution du code.
2 Références normatives
Les documents suivants sont cités dans le texte de sorte qu’ils constituent, pour tout ou partie de leur
contenu, des exigences du présent document. Pour les références datées, seule l’édition citée s’applique. Pour
les références non datées, la dernière édition du document de référence s'applique (y compris les éventuels
amendements).
ISO 11784, Identification des animaux par radiofréquence — Structure du code
ISO 11785:1996, Identification des animaux par radiofréquence — Concept technique
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s’appliquent.
L’ISO et l’IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l’adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l’adresse https:// www .electropedia .org/
3.1
champ d’activation
champ électromagnétique dont la fréquence est 134,2 kHz
3.2
code pays
code numérique de trois chiffres représentant un pays conformément à l’ISO 3166-1
3.3
code d’identification
code utilisé pour identifier individuellement l’animal au niveau national et, en l’associant au code pays (3.2),
au niveau international
Note 1 à l'article: Il incombe à chaque pays de s’assurer de l’unicité des codes d’identification nationaux.
3.4
émetteur-récepteur de référence en laboratoire
émetteur-récepteur utilisé pour soumettre à essai les transpondeurs en générant le champ d’activation (3.1),
capable de lire les transpondeurs FDX-B et HDX
3.5
fabricant
société qui soumet une demande d’essai de conformité ou d’attribution et d’utilisation d’un code de fabricant
(3.8) pour des transpondeurs conformes à l’ISO 11784 et à l’ISO 11785 et qui accepte les conditions
présentées à l’ISO 11784:2024, Annexe C ou l’ISO 11784:2024, Annexe C
Note 1 à l'article: voir également l’ISO 11784:2024, Annexe A.
3.6
code de fabricant
MFC [sigle de l’anglais manufacturer code]
numéro à trois chiffres attribué par le RA (3.13) à un fabricant (3.5) dans le respect des conditions exposées
à l’ISO 11784:2024, Annexe C, dont la plage de valeurs et l’emplacement dans la structure du code sont
conformes à l’ISO 11784
Note 1 à l'article: Un seul code de fabricant est attribué à un même fabricant.
3.7
enveloppe de protection primaire
couche de protection primaire des composants du transpondeur
3.8
code de produit
numéro à six chiffres attribué (et enregistré) par l’organisme d’enregistrement (3.13) à un fabricant (3.5)
pour un type de transpondeur donné, dont la première partie est le code de fabricant (3.6) et la deuxième
partie un numéro de série à trois chiffres
3.9
acheteur
personne, organisme ou société qui obtient la propriété légale du matériel en faisant une transaction sur ce
matériel
3.10
centre d’essai reconnu par le RA
centre d’essai répondant aux critères de l’organisme d’enregistrement (3.13)
3.11
transpondeur enregistré par le RA
transpondeur enregistré par l’organisme d’enregistrement (3.13)
3.12
fabricant enregistré par le RA
fabricant (3.5) disposant d’un ou de plusieurs transpondeurs enregistrés par le RA (3.11)
3.13
organisme d’enregistrement
RA [sigle de l’anglais registration authority]
autorité qui approuve des laboratoires d’essai et qui délivre et enregistre les codes de fabricant (3.5) et les
codes de produit (3.8)
3.14
rebouclage
processus consistant à attribuer à un nouveau transpondeur le même numéro d’identification qu’un
transpondeur (3.19) perdu ou qui est devenu illisible
3.15
compteur de rebouclage
champ de trois bits permettant de compter le nombre de rebouclages (3.14)
3.16
code de fabricant partagé
numéro à trois chiffres attribué par l’organisme d’enregistrement (3.13) à un fabricant (3.5) conformément à
l’ISO 11784:2024, Annexe C
Note 1 à l'article: Un code de fabricant partagé peut être attribué à plusieurs fabricants.
3.17
enveloppe de protection secondaire
couches supplémentaires recouvrant l’enveloppe de protection primaire (3.7) du transpondeur
3.18
émetteur-récepteur
dispositif utilisé pour communiquer avec le transpondeur (3.19)
3.19
tr
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.