ISO 23586:2022

INTERNATIONAL ISO
STANDARD 23586
First edition
2022-11
Conveyor belts — Indentation rolling
resistance related to belt width —
Requirements and testing
Courroies transporteuses — Résistance au roulement par suite
d'enfoncement relative à la largeur de courroie — Exigences et essais
Reference number
ISO 23586:2022(E)
© ISO 2022

---------------------- Page: 1 ----------------------
ISO 23586:2022(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
  © ISO 2022 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 23586:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Symbols and units. 1
5 Test rig . 2
6 Preparation of test samples .3
7 Procedure .4
8 Calculation and expression of results . 4
9 Test report . 5
Annex A (informative) Conversion of the measured width related indentation rolling
resistance to a 3-part idler station .7
Bibliography . 9
iii
© ISO 2022 – All rights reserved

---------------------- Page: 3 ----------------------
ISO 23586:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by TechnicalCommittee ISO/TC 41, Pulleys and belts (includingveebelts),
Subcommittee SC 3, Conveyor belts.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
  © ISO 2022 – All rights reserved

---------------------- Page: 4 ----------------------
ISO 23586:2022(E)
Introduction
The indentation rolling resistance is caused by the energy loss connected to the deformation of the
conveyor belt due to its contact with the idler. Apart from the technological properties of the conveyor
belt, the magnitude of the indentation rolling resistance depends on the following factors:
— design of the conveyor belt, especially the pulley side cover plate thickness;
— vertical load;
— idler diameter;
— ambient temperature;
— belt speed.
The width-related indentation rolling resistance is measured in a test rig with an idler which exerts an
evenly distributed vertical force on the belt. An indentation rolling resistance to be used for the design
of belt conveyors for an idler station with more than one idler can only be calculated considering the
vertical forces and their distribution between belt and idler (refer to Annex A).
v
© ISO 2022 – All rights reserved

---------------------- Page: 5 ----------------------
INTERNATIONAL STANDARD ISO 23586:2022(E)
Conveyor belts — Indentation rolling resistance related to
belt width — Requirements and testing
1 Scope
This document defines a method for the determination of the width-related indentation rolling
resistance of conveyor belts. The goal is to be a full-scale test and simulation on finished belt
constructions which are reproducible and relevant for the practical use. The test results can be used
for a comparison of conveyor belts and for design of belt conveyors with steel cord and fabric conveyor
belts.
This document is not suitable or valid for light conveyor belts described in ISO 21183-1.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
No terms and definitions are listed in this document.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
4 Symbols and units
Table 1 shows the symbols and units used in this document.
Table 1 — Symbols and units
Symbol Meaning Unit
B Belt width mm
b Width of the rubber edge of the belt mm
K
b Length of the contact line between belt and idler shell mm
R
Factor in the approximation equation for the width related inden-
c -
a
tation rolling resistance
Exponent in the approximation equation for the width related in-
c -
b
dentation rolling resistance
D Diameter of measuring idler mm
R,M
D Diameter of the opposing idler mm
R,G
D Steel cord diameter mm
S
D Pulley diameter mm
Tr
F Indentation rolling resistance acting on one idler N
E
Total indentation rolling resistance acting on an idler station with
F N
E,ges
three idlers
F´ Indentation rolling resistance related to belt width N/mm
E
1
© ISO 2022 – All rights reserved

---------------------- Page: 6 ----------------------
ISO 23586:2022(E)
TTabablele 1 1 ((ccoonnttiinnueuedd))
Symbol Meaning Unit
Horizontal force acting on the measuring idler turning clockwise
F N
M,h
(F ) or anti-clockwise (F )
M,h,r M,h,l
F , Vertical force on the measuring idler corresponding to the load N
M v
F´ Vertical force related to the belt width N/mm
M,v
F Normal force acting on an idler N
n
F Idler rolling resistance N
R
L Distance axis-to-axis mm
n Number of steel cords -
S
q Length related load acting on the idler N/mm
s Cover plate thickness, carrying side mm
1
s Cover plate thickness, pulley side mm
2
T Ambient temperature °C
U
t Cord pitch mm
v Belt speed m/s
z Coordinate of length mm
λ Idler trough angle °
Table 2 described the used indices in this document.
Table 2 — Indices
Index Meaning
m Middle idler
s Side idler
5 Test rig
The testing apparatus is a test rig with a rotating belt sample, constructed with a drive pulley and a
tensioning pulley. Both pulleys have a minimum diameter of 800 mm (Figure 1). The distance axis-
to-axis has a minimum value of 3 500 mm. For high strength conveyor belts and large splice lengths
differing pulley diameters and distances axis-to-axis shall be agreed upon with the operator of the test
rig. The belt speed is adjustable and is constantly monitored with appropriate sensors. The complete
test rig is placed in an isolated climate chamber, so that the ambient temperature can be adjusted with
suitable heating and cooling devices. There is a special measuring arrangement with which an idler can
be pressed on to the belt with a defined force. As counter support an idler is installed. This idler has
a minimum diameter D of 400 mm and the diameter shall be larger than the diameter D of the
R,G R,M
measuring idler by a minimum factor of 1,5 as Formula (1).
DD≥×15, (1)
R,GR,M
The diameters D and D shall be chosen corresponding to the parameters of the belt conve
...