ISO/TS 19392-1:2018
(Main)Paints and varnishes — Coating systems for wind-turbine rotor blades — Part 1: Minimum requirements and weathering
Paints and varnishes — Coating systems for wind-turbine rotor blades — Part 1: Minimum requirements and weathering
This document specifies minimum requirements and weathering for coating systems for wind-turbine rotor blades.
Peintures et vernis — Matériaux de revêtement pour pales de turbines éoliennes — Partie 1: Exigences minimales et érosion
General Information
Relations
Buy Standard
Standards Content (Sample)
TECHNICAL ISO/TS
SPECIFICATION 19392-1
First edition
2018-04
Paints and varnishes — Coating
systems for wind-turbine rotor
blades —
Part 1:
Minimum requirements and
weathering
Peintures et vernis — Matériaux de revêtement pour pales de turbines
éoliennes —
Partie 1: Exigences minimales et érosion
Reference number
ISO/TS 19392-1:2018(E)
©
ISO 2018
---------------------- Page: 1 ----------------------
ISO/TS 19392-1:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 19392-1:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements and test methods . 2
5 Sampling . 2
6 Preparation of test specimen . 2
7 Test methods . 2
7.1 Initial test methods . 2
7.2 Test methods after artificial weathering . 3
7.3 Test methods after humidity exposure . 4
7.4 Test methods after cyclic exposure . 4
7.5 Tensile tests . 5
8 Test report . 5
Annex A (informative) Test cycles for cyclic exposure . 6
© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 19392-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committ
...
TECHNICAL ISO/TS
SPECIFICATION 19392-1
First edition
2018-04
Paints and varnishes — Coating
systems for wind-turbine rotor
blades —
Part 1:
Minimum requirements and
weathering
Peintures et vernis — Matériaux de revêtement pour pales de turbines
éoliennes —
Partie 1: Exigences minimales et érosion
Reference number
ISO/TS 19392-1:2018(E)
©
ISO 2018
---------------------- Page: 1 ----------------------
ISO/TS 19392-1:2018(E)
COPYRIGHT PROTECTED DOCUMENT
© ISO 2018
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting
on the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address
below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Fax: +41 22 749 09 47
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii © ISO 2018 – All rights reserved
---------------------- Page: 2 ----------------------
ISO/TS 19392-1:2018(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Requirements and test methods . 2
5 Sampling . 2
6 Preparation of test specimen . 2
7 Test methods . 2
7.1 Initial test methods . 2
7.2 Test methods after artificial weathering . 3
7.3 Test methods after humidity exposure . 4
7.4 Test methods after cyclic exposure . 4
7.5 Tensile tests . 5
8 Test report . 5
Annex A (informative) Test cycles for cyclic exposure . 6
© ISO 2018 – All rights reserved iii
---------------------- Page: 3 ----------------------
ISO/TS 19392-1:2018(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committ
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.