ISO 11199-2:2021/PRF Amd 1
(Amendment)Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators — Amendment 1: Removal of brake requirements
Assistive products for walking manipulated by both arms — Requirements and test methods — Part 2: Rollators — Amendment 1: Removal of brake requirements
Produits d’assistance à la marche manipulés avec les deux bras — Exigences et méthodes d’essai — Partie 2: Déambulateurs — Amendement 1: Suppression des exigences relatives aux freins
General Information
Relations
Buy Standard
Standards Content (Sample)
International
Standard
ISO 11199-2
Third edition
Assistive products for walking
2021-07
manipulated by both arms —
Requirements and test methods —
AMENDMENT 1
Part 2:
Rollators
AMENDMENT 1: Removal of brake
requirements
Produits d’assistance à la marche manipulés avec les deux bras —
Exigences et méthodes d’essai —
Partie 2: Déambulateurs
AMENDEMENT 1: Suppression des exigences relatives aux freins
PROOF/ÉPREUVE
Reference number
ISO 11199-2:2021/Amd.1:2024(en) © ISO 2024
ISO 11199-2:2021/Amd.1:2024(en)
© ISO 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
PROOF/ÉPREUVE
ii
ISO 11199-2:2021/Amd.1:2024(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve th
...
ISO 11199-2:2021/PRF Amd .1:2024(E)
2024-0X-XX
ISO/TC 173
Secretariat: KATS SIS
Date: 2024-09-30
Assistive products for walking manipulated by both arms —
Requirements and test methods – —
Part 2:
Rollators
AMENDMENT 1: Removal of brake requirements
Produits d’assistance à la marche manipulés avec les deux bras — Exigences et méthodes d’essai —
Partie 2: Déambulateurs
AMENDEMENT 1: Suppression des exigences relatives aux freins
PROOF
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
Fax: +41 22 749 09 47
EmailE-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.