ISO/IEC 17341:2005

INTERNATIONAL ISO/IEC
STANDARD 17341
Second edition
2005-02-01


Information technology — Data
interchange on 120 mm and 80 mm
optical disk using +RW format —
Capacity: 4,7 Gbytes and 1,46 Gbytes per
side (Recording speed up to 4X)
Technologies de l'information — Échange de données sur disque
optique de 120 mm et 80 mm en utilisant le format +RW — Capacité:
4,7 Go et 1,46 Go par face (Vitesse d'enregistrement inférieure ou
égale à 4X)




Reference number
ISO/IEC 17341:2005(E)
©
ISO/IEC 2005

---------------------- Page: 1 ----------------------
ISO/IEC 17341:2005(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO/IEC 2005
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO/IEC 2005 – All rights reserved

---------------------- Page: 2 ----------------------
ISO/IEC 17341:2005(E)
Contents Page
Foreword. vii
Section 1 — General . 1
1 Scope. 1
2 Conformance . 1
2.1 Optical Disk . 1
2.2 Generating system. 1
2.3 Receiving system. 2
2.4 Compatibility statement . 2
3 Normative references . 2
4 Terms and definitions. 2
5 Conventions and notations. 4
5.1 Representation of numbers . 4
5.2 Names. 4
6 List of acronyms . 4
7 General description of the optical disk. 5
8 General Requirements. 6
8.1 Environments . 6
8.1.1 Test environment . 6
8.1.2 Operating environment. 6
8.1.3 Storage environment . 7
8.1.4 Transportation. 7
8.2 Safety requirements. 7
8.3 Flammability . 7
9 Reference Drive. 7
9.1 Optical system. 7
9.2 Optical beam. 8
9.3 Read channel 1. 9
9.4 Disk clamping. 9
9.5 Rotation of the disk. 9
9.6 Wobble channel (Read channel 2). 10
9.7 Tracking channel (Read channel 2). 10
9.7.1 Normalized servo transfer function . 10
9.7.2 Reference Servo for Axial Tracking . 10
9.7.3 Reference Servo for Radial Tracking . 11
Section 2 — Dimensional, mechanical and physical characteristics of the disk. 13
10 Dimensional characteristics . 13
10.1 Reference Planes . 13
10.2 Overall dimensions . 13
10.3 First transition area. 14
10.4 Second transition area . 14
10.5 Clamping Zone . 14
10.6 Third transition area . 14
10.7 Information Zone. 14
10.8 Rim area . 15
10.9 Remark on tolerances. 15
11 Mechanical characteristics . 17
© ISO/IEC 2005 – All rights reserved iii

---------------------- Page: 3 ----------------------
ISO/IEC 17341:2005(E)
11.1 Mass.17
11.2 Moment of inertia.17
11.3 Dynamic imbalance.17
11.4 Axial runout.17
11.5 Radial runout .17
12 Optical characteristics in the Information Zone.18
12.1 Index of refraction .18
12.2 Thickness of the substrate.18
12.3 Reflectivity .18
12.4 Birefringence .18
12.5 Angular deviation .19
Section 3 — Format of information .20
13 Data format.20
13.1 Data Frames .20
13.1.1 Identification Data (ID) .21
13.1.2 ID Error Detection Code (IED) .21
13.1.3 RSV .22
13.1.4 Error Detection Code (EDC) .22
13.2 Scrambled Frames .22
13.3 ECC Blocks .23
13.4 Recording Frames.24
13.5 Modulation and NRZI conversion .25
13.6 Physical Sectors.26
13.7 Layout of a Recording UNit (RUN).27
13.7.1 Recording Unit position.28
13.8 d.c. component suppression control .28
14 Track format.29
14.1 Track shape.29
14.2 Track path .30
14.3 Track pitch .30
14.4 Track layout .30
14.4.1 ADIP information .30
14.4.2 Physical format information in ADIP.35
Section 4 — Format of the Information Zone .48
15 General description of the Information Zone .48
16 Layout of the Information Zone .48
16.1 Physical Sector Numbers (PSNs) .48
17 Lead-in Zone .49
17.1 Initial Zone.50
17.2 Inner Disk Test Zone .50
17.3 Inner Drive Test Zone.50
17.4 Guard Zone 1 .51
17.5 Reserved Zone 1.51
17.6 Reserved Zone 2.51
17.7 Inner Disk Identification Zone.51
17.8 Reserved Zone 3.51
17.9 Reference Code Zone .51
17.10 Buffer Zone 1 .51
17.11 Control Data Zone .51
17.11.1 Physical format information.53
17.11.2 Disk manufacturing information.54
17.11.3 Content provider information.54
17.12 Buffer Zone 2 .54
18 Data Zone .54
19 Lead-out Zone.54
iv © ISO/IEC 2005 – All rights reserved

---------------------- Page: 4 ----------------------
ISO/IEC 17341:2005(E)
19.1 Buffer Zone 3 . 55
19.2 Outer Disk Identification Zone. 55
19.3 Guard Zone 2 . 55
19.4 Reserved Zone 4 . 55
19.5 Outer Drive Test Zone. 55
19.6 Outer Disk Test Zone. 55
19.7 Guard Zone 3 . 55
20 Assignment of Logical Sector Numbers (LSNs). 56
21 Formatting. 56
21.1 Pre-formatting . 56
21.1.1 Verification. 57
21.2 Background formatting . 57
21.2.1 Initialization . 57
21.2.2 De-icing . 57
21.2.3 Finalization. 57
21.2.4 Verification (optional) . 57
21.3 Sequential recording without formatting. 58
22 Disk Control Blocks . 58
22.1 General format of Disk Control Blocks. 58
22.2 Format of the Formatting DCB (FDCB) .60
22.3 Format of the Write inhibit DCB (WDCB).64
Section 5 — Characteristics of the groove. 66
23 General. 66
24 Method of testing . 66
24.1 Environment . 66
24.2 Reference Drive. 66
24.2.1 Optics and mechanics. 66
24.2.2 Read power. 66
24.2.3 Read channels. 66
24.2.4 Tracking . 66
24.3 Definition of signals. 67
25 Characteristics of the groove signals. 67
25.1 Phase depth. 67
25.2 Push-pull signal . 67
25.3 Track Cross signal . 68
25.4 Normalized wobble signal. 68
25.5 Characteristics of the wobble. 68
Section 6 — Characteristics of the recording layer . 69
26 Method of testing . 69
26.1 Environment . 69
26.2 Reference Drive. 69
26.2.1 Optics and mechanics. 69
26.2.2 Read power. 69
26.2.3 Read channels. 69
26.2.4 Tracking . 69
26.2.5 Scanning velocity. 70
26.3 Write conditions . 70
26.3.1 Write pulse waveform. 70
26.3.2 Write power. 70
26.4 Measurement conditions. 70
27 Characteristics of the recorded signals . 70
27.1 Channel bit length. 70
27.2 Definition of signals. 71
27.2.1 High frequency signals (HF) . 71
27.2.2 Modulated amplitude . 71
© ISO/IEC 2005 – All rights reserved v

---------------------- Page: 5 ----------------------
ISO/IEC 17341:2005(E)
27.2.3 Signal asymmetry.71
27.2.4 Normalized Slicing Level jump .72
27.2.5 Jitter.72
27.2.6 Track Cross signal .72
27.3 Read stability .72
28 Additional testing conditions.73
28.1 Test environment.73
28.1.1 Optics .73
28.2 Definition of signals .73
28.2.1 Modulated amplitude.73
28.2.2 Signal asymmetry.73
28.2.3 Jitter.74
28.2.4 Track Cross signal .74
28.2.5 Differential phase tracking error signal .74
28.2.6 Tangential push-pull signal.75
29 Quality of the recording layer .75
29.1 Defects.75
29.2 Data errors .76
Section 7 — Characteristics of user data .77
30 Method of testing.77
30.1 Environment.77
30.2 Reference Drive .77
30.2.1 Optics and mechanics .77
30.2.2 Read power .
...