ISO 24204:2025
(Main)Oil and gas industries including lower carbon energy — Bulk material for offshore projects — Design for architectural supports
Oil and gas industries including lower carbon energy — Bulk material for offshore projects — Design for architectural supports
This document specifies the design requirements for architectural supports, in terms of their shape and dimensions, material, strength, etc. This document covers architectural supports of topside and living-quarter regions for fixed or floating offshore oil and gas platforms including lower carbon energy.
Industries du pétrole et du gaz, y compris les énergies à faible teneur en carbone — Matériels de base pour les projets en mer — Conception pour les supports architecturaux
Le présent document spécifie les exigences de conception pour les supports architecturaux, en matière de forme et de dimensions, de matériaux, de résistance, etc. Le présent document couvre les supports architecturaux des zones Top Sides et des quartiers de vie pour les plateformes pétrolières et gazières en mer fixes ou flottantes, y compris les énergies à faible teneur en carbone.
General Information
Buy Standard
Standards Content (Sample)
International
Standard
ISO 24204
First edition
Oil and gas industries including
2025-02
lower carbon energy — Bulk
material for offshore projects —
Design for architectural supports
Industries du pétrole et du gaz, y compris les énergies à faible
teneur en carbone — Matériels de base pour les projets en mer —
Conception pour les supports architecturaux
Reference number
© ISO 2025
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Architectural support specification . 2
4.1 General .2
4.2 Lining panel support specification .2
4.2.1 Key parameters .2
4.2.2 Shape and dimensional specifications .3
4.2.3 Connection detail specification .4
4.2.4 Material specification .5
4.2.5 Maximum support length .5
4.2.6 Specification of maximum pitch for lining support . .5
4.2.7 Application of double pads .6
4.3 Partition panel support specification .6
4.3.1 Key parameters .6
4.3.2 Shape and dimensional specifications .7
4.3.3 Connection detail specification .7
4.3.4 Material specification .7
4.3.5 Maximum support height .8
4.3.6 Specification of maximum pitch for partition panel support .8
4.3.7 Application of double pads .9
4.4 Coaming plate specification . .9
4.4.1 Key parameters .9
4.4.2 Shape and dimensional specifications .10
4.4.3 Connection detail specification .10
4.4.4 Material specification .10
4.5 Technical liner support specification .11
4.5.1 Key parameters .11
4.5.2 Types of technical liner support .11
4.5.3 Shape and dimensional specifications . 13
4.5.4 Connection detail specification . 13
4.5.5 Material specification .14
4.5.6 Application of double pads .14
4.6 Equipment supports on wall panel .14
4.6.1 General .14
4.6.2 Wall-mounted equipment support . 15
4.6.3 Deck-mounted equipment support .18
4.6.4 Material specification .19
4.6.5 Connection detail specification .19
4.6.6 Application of double pads .19
Annex A (informative) Quality control plan (QCP) .21
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee
has been established has the right to be represented on that committee. International organizations,
governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely
with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types
of ISO document should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent
rights in respect thereof. As of the date of publication of this document, ISO had not received notice of (a)
patent(s) which may be required to implement this document. However, implementers are cautioned that
this may not represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 67, Oil and gas industries including lower
carbon energy.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
Based on an assessment of past offshore projects, this document aims to provide a set of unified design
specifications for architectural supports for offshore projects, responding to the current lack of recognized
specifications for such supports in terms of shapes, sizes, dimensions, material and application area.
Company-specific standards from owners, engineering companies and shipbuilders have been prevailing for
such specifications There are big variations in specifications from project to project, because of the lack of
international recognized specifications within this area.
Thus, individual architectural supports have often failed to be compatible across different projects. With this
document, one unified approach can be applied for their design, material selection, shape and application,
etc. This can significantly reduce the delivery time and improve the engineering and fabrication efficiency.
Another expected benefit is improvement on the design and application of architectural support types
related to design life, maintainability and integrity.
v
International Standard ISO 24204:2025(en)
Oil and gas industries including lower carbon energy — Bulk
material for offshore projects — Design for architectural
supports
1 Scope
This document specifies the design requirements for architectural supports, in terms of their shape and
dimensions, material, strength, etc. This document covers architectural supports of topside and living-
quarter regions for fixed or floating offshore oil and gas platforms including lower carbon energy.
2 Normative references
There are no normative references in this document.
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https:// www .iso .org/ obp
— IEC Electropedia: available at https:// www .electropedia .org/
3.1
architectural support
member, attached to adjacent structural members, used to maintain the position of architectural
components, but not subject to take significant loads from the architectural components
EXAMPLE Lining panel (3.6), partition panel (3.7).
3.2
architectural welding
welding used to fix the architectural support (3.1) of equal angle or flat bar to the structural member
3.3
ceiling panel
overhead interior surface that covers the upper limits of a room, connected with the wall system by being
either suspended or self-supported
3.4
coaming plate
steel flat bar or vertical surface which is provided to prevent ingress of water
3.5
equipment support
architectural member to support equipment installed on the wall panel (3.12)
3.6
lining panel
non-load-bearing proprietary sandwich panel system of 25 mm in thickness, consisting of mi
...
Norme
internationale
ISO 24204
Première édition
Industries du pétrole et du gaz,
2025-02
y compris les énergies à faible
teneur en carbone — Matériels
de base pour les projets en mer
— Conception pour les supports
architecturaux
Oil and gas industries including lower carbon energy — Bulk
material for offshore projects — Design for architectural
supports
Numéro de référence
DOCUMENT PROTÉGÉ PAR COPYRIGHT
© ISO 2025
Tous droits réservés. Sauf prescription différente ou nécessité dans le contexte de sa mise en œuvre, aucune partie de cette
publication ne peut être reproduite ni utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique,
y compris la photocopie, ou la diffusion sur l’internet ou sur un intranet, sans autorisation écrite préalable. Une autorisation peut
être demandée à l’ISO à l’adresse ci-après ou au comité membre de l’ISO dans le pays du demandeur.
ISO copyright office
Case postale 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Genève
Tél.: +41 22 749 01 11
E-mail: copyright@iso.org
Web: www.iso.org
Publié en Suisse
ii
Sommaire Page
Avant-propos .iv
Introduction .v
1 Domaine d'application . 1
2 Références normatives . 1
3 Termes et définitions . 1
4 Spécification d'un support architectural . 2
4.1 Généralités .2
4.2 Spécification d'un support de panneau de revêtement .3
4.2.1 Paramètres clés .3
4.2.2 Spécifications de forme et de dimensions .3
4.2.3 Spécification particulière de raccordement . .5
4.2.4 Spécification du matériau .6
4.2.5 Longueur maximale du support .6
4.2.6 Spécification d'un espacement maximal pour un support de revêtement .6
4.2.7 Application de doubles bossages . .7
4.3 Spécification d'un support de panneau de séparation .7
4.3.1 Paramètres clés .7
4.3.2 Spécifications de forme et de dimensions .7
4.3.3 Spécification particulière de raccordement . .7
4.3.4 Spécification du matériau .8
4.3.5 Hauteur de support maximale .8
4.3.6 Spécification d'un espacement maximal pour un support de panneau de
séparation .9
4.3.7 Application de doubles bossages . .10
4.4 Spécification d'une plaque d'hiloire.10
4.4.1 Paramètres clés .10
4.4.2 Spécifications de forme et de dimensions .11
4.4.3 Spécification particulière de raccordement . .11
4.4.4 Spécification du matériau . 12
4.5 Spécification d'un support de revêtement technique . 12
4.5.1 Paramètres clés . 12
4.5.2 Types de supports de revêtement technique . 12
4.5.3 Spécifications de forme et de dimensions . 15
4.5.4 Spécification particulière de raccordement . . 15
4.5.5 Spécification du matériau .16
4.5.6 Application de doubles bossages . .16
4.6 Supports d'équipement sur panneau mural .16
4.6.1 Généralités .16
4.6.2 Support d'équipement monté sur mur .17
4.6.3 Support d'équipement monté sur pont . 20
4.6.4 Spécification du matériau .21
4.6.5 Spécification particulière de raccordement . .21
4.6.6 Application de doubles bossages . .21
Annexe A (informative) Plan de contrôle de la qualité (QCP) .23
iii
Avant-propos
L'ISO (Organisation internationale de normalisation) est une fédération mondiale d'organismes nationaux
de normalisation (comités membres de l'ISO). L'élaboration des Normes internationales est en général
confiée aux comités techniques de l'ISO. Chaque comité membre intéressé par une étude a le droit de faire
partie du comité technique créé à cet effet. Les organisations internationales, gouvernementales et non
gouvernementales, en liaison avec l'ISO participent également aux travaux. L'ISO collabore étroitement avec
la Commission électrotechnique internationale (IEC) en ce qui concerne la normalisation électrotechnique.
Les procédures utilisées pour élaborer le présent document et celles destinées à sa mise à jour sont
décrites dans les Directives ISO/IEC, Partie 1. Il convient, en particulier, de prendre note des différents
critères d'approbation requis pour les différents types de documents ISO. Le présent document
a été rédigé conformément aux règles de rédaction données dans les Directives ISO/IEC, Partie 2
(voir www.iso.org/directives).
L'ISO attire l'attention sur le fait que la mise en application du présent document peut entraîner l'utilisation
d'un ou de plusieurs brevets. L'ISO ne prend pas position quant à la preuve, à la validité et à l'applicabilité de
tout droit de propriété revendiqué à cet égard. À la date de publication du présent document, l'ISO n'avait pas
reçu notification qu'un ou plusieurs brevets pouvaient être nécessaires à sa mise en application. Toutefois,
il y a lieu d'avertir les responsables de la mise en application du présent document que des informations
plus récentes sont susceptibles de figurer dans la base de données de brevets, disponible à l'adresse
www.iso.org/brevets. L'ISO ne saurait être tenue pour responsable de ne pas avoir identifié tout ou partie de
tels droits de brevet.
Les appellations commerciales éventuellement mentionnées dans le présent document sont données pour
information, par souci de commodité, à l'intention des utilisateurs et ne sauraient constituer un engagement.
Pour une explication de la nature volontaire des normes, la signification des termes et expressions
spécifiques de l'ISO liés à l'évaluation de la conformité, ou pour toute information au sujet de l'adhésion de
l'ISO aux principes de l'Organisation mondiale du commerce (OMC) concernant les obstacles techniques au
commerce (OTC), voir www.iso.org/avant-propos.
Le présent document a été élaboré par le comité technique ISO/TC 67, Industries du pétrole et du gaz, y
compris les énergies à faible teneur en carbone.
Il convient que l'utilisateur adresse tout retour d'information ou toute question concernant le présent
document à l'organisme national de normalisation de son pays. Une liste exhaustive desdits organismes se
trouve à l'adresse www.iso.org/fr/members.html.
iv
Introduction
Le présent document, qui se base sur l'évaluation des projets en mer antérieurs, a pour objectif de fournir un
ensemble de spécifications de conception unifiées pour les supports architecturaux dans le cadre des projets
en mer, et de répondre au manque actuel de spécifications reconnues pour lesdits supports en termes de
formes, tailles, dimensions, matériaux et domaines d'application.
Les normes spécifiques de chaque société propriétaire, société d'ingénierie et constructeur naval ont par
conséquent prévalu pour de telles spécifications. Les spécifications varient considérablement d'un projet à
l'autre en raison d'un manque de spécifications internationales reconnues dans ce domaine.
Par conséquent, les différents supports architecturaux n'ont souvent pas été compatibles entre les projets.
Avec le présent document, une approche unifiée peut être appliquée pour leur conception, sélection des
matériaux, forme et application, etc. Cela peut réduire considérablement le délai de livraison et améliorer
l'efficacité de l'ingénierie et de la fabrication. Un autre bénéfice attendu est une amélioration en matière
de conception et d'application des types de supports architecturaux en ce qui concerne la durée de vie, la
maintenabilité et l'intégrité.
v
Norme internationale ISO 24204:2025(fr)
Industries du pétrole et du gaz, y compris les énergies à faible
teneur en carbone — Matériels de base pour les projets en
mer — Conception pour les supports architecturaux
1 Domaine d'application
Le présent document spécifie les exigences de conception pour les supports architecturaux, en matière
de forme et de dimensions, de matériaux, de résistance, etc. Le présent document couvre les supports
architecturaux des zones Top Sides et des quartiers de vie pour les plateformes pétrolières et gazières en
mer fixes ou flottantes, y compris les énergies à faible teneur en carbone.
2 Références normatives
Le présent document ne contient aucune référence normative.
3 Termes et définitions
Pour les besoins du présent document, les termes et définitions suivants s'appliquent.
L'ISO et l'IEC tiennent à jour des bases de données terminologiques destinées à être utilisées en normalisation,
consultables aux adresses suivantes:
— ISO Online browsing platform: disponible à l'adresse https:// www .iso .org/ obp
— IEC Electropedia: disponible à l'adresse https:// www .electropedia .org/
3.1
support architectural
élément, fixé aux éléments structuraux adjacents, utilisé pour maintenir la position des éléments
architecturaux, mais non soumis à des charges significatives par les éléments architecturaux
EXEMPL
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.