ISO 26243:2007

INTERNATIONAL ISO

STANDARD 26243

First edition
2007-12-15

Cards for staple fibres spinning —
Vocabulary and principles of
construction
Cardeuse pour la filature des fibres discontinues — Terminologie,
principes de construction





Reference number
ISO 26243:2007(E)
©
ISO 2007

---------------------- Page: 1 ----------------------
ISO 26243:2007(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.



COPYRIGHT PROTECTED DOCUMENT


©  ISO 2007
The reproduction of the terms and definitions contained in this International Standard is permitted in teaching manuals, instruction
booklets, technical publications and journals for strictly educational or implementation purposes. The conditions for such reproduction are:
that no modifications are made to the terms and definitions; that such reproduction is not permitted for dictionaries or similar publications
offered for sale; and that this International Standard is referenced as the source document.
With the sole exceptions noted above, no other part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland

ii © ISO 2007 – All rights reserved

---------------------- Page: 2 ----------------------
ISO 26243:2007(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 26243 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories,
Subcommittee SC 1, Spinning preparatory, spinning, twisting and winding machinery and accessories.

© ISO 2007 – All rights reserved iii

---------------------- Page: 3 ----------------------
INTERNATIONAL STANDARD ISO 26243:2007(E)

Cards for staple fibres spinning — Vocabulary and principles of
construction
1 Scope
This International Standard specifies terms and definitions for the card with regard to spinning procedure for
cotton and other staple fibres.
2 Normative references
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
ISO 92, Textile machinery and accessories — Spinning machinery — Definition of sides (left or right)
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
NOTE The descriptions with parenthesised numbers are dealt with separately under these numbers.
3.1 Basic terms
3.1.1
card
machine to open fibre tufts – up to the single fibre – to separate contamination, dust and short fibres, and to
produce a web that will be formed into the sliver
3.1.2
flat card
card that is characterized by movable flats above the cylinder (3.4.4)
© ISO 2007 – All rights reserved 1

---------------------- Page: 4 ----------------------
ISO 26243:2007(E)
3.2 Width dimensions
See Figure 1.
Dimensions in millimetres

Figure 1 — Width dimensions
3.2.1
clothing width
B
decisive width for calculating the clothing length, equivalent to the cylinder width W, less possible end plates
3.2.2
cylinder width
W
complete width of roll barrel, including possible end plates
3.2.3
working width
A
cover width of fibre material on the roll
2 © ISO 2007 – All rights reserved

---------------------- Page: 5 ----------------------
ISO 26243:2007(E)
3.3 Definition of sides, dimensions
See Figure 2.

Key
1 feed area (rear)
2 delivery area (front)
b machine width (over casing)
l machine length (without deposit system)
R right side
L left side
Figure 2 — Definition of sides, dimensions
3.3.1
right side
R
side on the right, when looking against the fibre flow
See ISO 92.
3.3.2
left side
L
side on the left, when looking against the fibre flow
See ISO 92.
3.3.3
work flow direction
material flow
direction of fibre flow
3.3.4
drive side
side equipped with cylinder (3.4.4) drive
© ISO 2007 – All rights reserved 3

-----------
...