ISO 2974

ISO/FDIS 2974
ISO/TC 22/SC 34
Secretariat: JISC
Diesel engines — 60° concave cones for high-pressure fuel injection
components
Moteurs diesels — Raccords finaux à cône concave de 60° pour lignes d'injection de carburants haute pression
FDIS stage
ISO/FDIS 2974:2026(en)
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication
may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying,
or posting on the internet or an intranet, without prior written permission. Permission can be requested from either ISO
at the address below or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: + 41 22 749 01 11
E-mail: copyright@iso.org
Website: www.iso.org
Published in Switzerland
ii
ISO/FDIS 2974:2026(en)
Contents
Foreword . iv
Introduction . v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Requirements . 2
4.1 Dimensions and tolerances . 2
4.2 Materials . 2
5 Designation . 2
6 Figures and tables . 3
6.1 Integral 60° concave cone . 3
6.2 Fabricated 60° concave cone . 8
Bibliography . 13

iii
ISO/FDIS 2974:2026(en)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out through
ISO technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are described
in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the different types of
ISO documents should be noted. This document was drafted in accordance with the editorial rules of the
ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed patent rights
in respect thereof. As of the date of publication of this document, ISO had not received notice of (a) patent(s)
which may be required to implement this document. However, implementers are cautioned that this may not
represent the latest information, which may be obtained from the patent database available at
www.iso.org/patents. ISO shall not be held responsible for identifying any or all such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and expressions
related to conformity assessment, as well as information about ISO's adherence to the World Trade
Organization (WTO) principles in the Technical Barriers to Trade (TBT), see the following URL::
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 022, Road vehicles, Subcommittee SC 34,
Propulsion, powertrain and powertrain fluids.
This tenth edition cancels and replaces the ninth edition (ISO 2974:2018), which has been technically revised.
The main changes compared to the previous edition are as follows:
— — Language inclusivity was improved;
— — New thread option M16 × × 1.,0 in Table 1Table 1;;
— — Updated reference standard ISO 21920-1 for roughness indication.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO/FDIS 2974:2026(en)
Introduction
To comply with recent exhaust gas regulations and fuel consumption regulations for internal combustion
engines, the fuel injection pressure of automobile diesel engines is generally 2 000 bar or more. Engines of
2 700 bar are also being introduced to the market.
Since this fuel injection pressure is extremely high, the dimensions and specifications of the 60° concave cones
for high pressure fuel connections are serialised. This is to prevent fuel leaking from the joint or other failures.
v
Diesel engines — 60° concave cones for high-pressure fuel injection
components
1 Scope
This document specifies the dimensional requirements of end-connections for high-pressure fuel injection
equipment components, that are fuel injectors, CR injectors, common rails, distribution blocks, injection
pumps, high-pressure supply pumps used on diesel (compression-ignition) engines.
It is applicable to externally threaded 60° concave cones (see Figures 1, 2, 5, and 6) and intended for use with
high-pressure fuel injection pipe assemblies with tube outside diameters of:
— up to and including 12 mm for integral concave cones (see Table 1); and
— up to and including 9 mm for fabricated concave cones (see Table 2).
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content constitutes
requirements of this document. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
ISO 261, ISO general purpose metric screw threads — General plan
ISO 21920--1, Geometrical product specifications (GPS) — Surface texture: Profile — Part 1: Indication of
surface texture
ISO 3508, Thread run-outs for fasteners with thread in accordance with ISO 261 and ISO 262
ISO 13296, Diesel engines — High-pressure fuel injection pipe assemblies — General requirements and
dimensions
3 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
ISO and IEC maintain terminology databases for use in standardization at the following addresses:
— ISO Online browsing platform: available at https://www.iso.org/obp
— IEC Electropedia: available at https://www.electropedia.org/
3.1
integral concave cone
concave cone where the sealing cone and the thread are connected in the same part
Note 1 to entry: See Figures 1 and 2.
3.2
fabricated concave cone
concave cone where the sealing cone and the thread are separate parts prior to joining, e.g. by welding
Note 1 to entry: See Figures 5 and 6.

ISO/FDIS 2974:2026(en)
3.3
reference diameter
S
baseline for dimensioning of the concave cone and the pipe end form
Note 1 to entry: S can be coincident with the intended nominal sealing interface between the concave cone and the pipe
end form, or not.
4 Requirements
4.1 Dimensions and tolerances
The 60° concave cone and its relationship to the external thread shall meet the requirements of Figure 1
(integral concave cones) or Figure 5 (fabricated concave cones). However, for integral concave cones,
variations at the smaller end of the concave cone as shown in Figure 3 are acceptable.
Dimensions and tolerances are given in Table 1 (integral concave cones) and Table 2 (fabricated concave
cones). Unspecified details are left to the manufacturer's choice.
With reference to dimension T in Figures 1, 2, 5, and 6, the external thread may be either with or without
undercut. However, it shall be possible to screw the GO-gauge for the thread up to the plane specified by
dimension T.
Figure 4 and Figure 7 show the assemblies with pipe end connections for the integral and fabricated concave
cone types, respectively.
4.2 Materials
The specification of material and heat treatmen
...