IEC 61784-5-22:2024

IEC 61784-5-22 ®
Edition 1.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Industrial networks – Profiles –
Part 5-22: Installation of fieldbuses – Installation profiles for CPF 22

Réseaux industriels – Profils –
Partie 5-22: Installation des bus de terrain – Profils d'installation pour CPF 22
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form
or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from
either IEC or IEC's member National Committee in the country of the requester. If you have any questions about IEC
copyright or have an enquiry about obtaining additional rights to this publication, please contact the address below or
your local IEC member National Committee for further information.

Droits de reproduction réservés. Sauf indication contraire, aucune partie de cette publication ne peut être reproduite ni
utilisée sous quelque forme que ce soit et par aucun procédé, électronique ou mécanique, y compris la photocopie et
les microfilms, sans l'accord écrit de l'IEC ou du Comité national de l'IEC du pays du demandeur. Si vous avez des
questions sur le copyright de l'IEC ou si vous désirez obtenir des droits supplémentaires sur cette publication, utilisez
les coordonnées ci-après ou contactez le Comité national de l'IEC de votre pays de résidence.

IEC Secretariat Tel.: +41 22 919 02 11
3, rue de Varembé info@iec.ch
CH-1211 Geneva 20 www.iec.ch
Switzerland
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.

About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigendum or an amendment might have been published.

IEC publications search - webstore.iec.ch/advsearchform IEC Products & Services Portal - products.iec.ch
The advanced search enables to find IEC publications by a Discover our powerful search engine and read freely all the
variety of criteria (reference number, text, technical publications previews, graphical symbols and the glossary.
committee, …). It also gives information on projects, replaced With a subscription you will always have access to up to date
and withdrawn publications. content tailored to your needs.

IEC Just Published - webstore.iec.ch/justpublished
Electropedia - www.electropedia.org
Stay up to date on all new IEC publications. Just Published
The world's leading online dictionary on electrotechnology,
details all new publications released. Available online and once
containing more than 22 500 terminological entries in English
a month by email.
and French, with equivalent terms in 25 additional languages.

Also known as the International Electrotechnical Vocabulary
IEC Customer Service Centre - webstore.iec.ch/csc
(IEV) online.
If you wish to give us your feedback on this publication or need

further assistance, please contact the Customer Service
Centre: sales@iec.ch.
A propos de l'IEC
La Commission Electrotechnique Internationale (IEC) est la première organisation mondiale qui élabore et publie des
Normes internationales pour tout ce qui a trait à l'électricité, à l'électronique et aux technologies apparentées.

A propos des publications IEC
Le contenu technique des publications IEC est constamment revu. Veuillez vous assurer que vous possédez l’édition la
plus récente, un corrigendum ou amendement peut avoir été publié.

Recherche de publications IEC -  IEC Products & Services Portal - products.iec.ch
webstore.iec.ch/advsearchform Découvrez notre puissant moteur de recherche et consultez
La recherche avancée permet de trouver des publications IEC gratuitement tous les aperçus des publications, symboles
en utilisant différents critères (numéro de référence, texte, graphiques et le glossaire. Avec un abonnement, vous aurez
comité d’études, …). Elle donne aussi des informations sur les toujours accès à un contenu à jour adapté à vos besoins.
projets et les publications remplacées ou retirées.

Electropedia - www.electropedia.org
IEC Just Published - webstore.iec.ch/justpublished
Le premier dictionnaire d'électrotechnologie en ligne au monde,
Restez informé sur les nouvelles publications IEC. Just
avec plus de 22 500 articles terminologiques en anglais et en
Published détaille les nouvelles publications parues.
français, ainsi que les termes équivalents dans 25 langues
Disponible en ligne et une fois par mois par email.
additionnelles. Egalement appelé Vocabulaire

Electrotechnique International (IEV) en ligne.
Service Clients - webstore.iec.ch/csc

Si vous désirez nous donner des commentaires sur cette
publication ou si vous avez des questions contactez-nous:
sales@iec.ch.
IEC 61784-5-22 ®
Edition 1.0 2024-03
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Industrial networks – Profiles –

Part 5-22: Installation of fieldbuses – Installation profiles for CPF 22

Réseaux industriels – Profils –

Partie 5-22: Installation des bus de terrain – Profils d'installation pour CPF 22

INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 25.040  ISBN 978-2-8322-8350-9

– 2 – IEC 61784-5-22:2024 © IEC 2024
CONTENTS
FOREWORD . 4
INTRODUCTION . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and abbreviated terms . 7
4 CPF 22: Overview of installation profiles . 7
5 Installation profile conventions. 8
6 Conformance to installation profiles . 8
Annex A (normative) CP 22/1 (AUTBUS™) specific installation profile . 10
A.1 Installation profile scope . 10
A.2 Normative references . 10
A.3 Installation profile terms, definitions, and abbreviated terms . 10
A.3.1 Terms and definitions . 10
A.3.2 Abbreviated terms . 10
A.3.3 Conventions for installation profiles . 10
A.4 Installation planning . 10
A.4.1 General . 10
A.4.2 Planning requirements . 10
A.4.3 Network capabilities . 11
A.4.4 Selection and use of cabling components . 12
A.4.5 Cabling planning documentation . 16
A.4.6 Verification of cabling planning specification . 16
A.5 Installation implementation. 16
A.5.1 General requirements . 16
A.5.2 Cable installation . 17
A.5.3 Connector installation . 17
A.5.4 Terminator installation . 18
A.5.5 Device installation . 18
A.5.6 Coding and labelling . 18
A.5.7 Earthing and bonding of equipment and devices and shield cabling . 18
A.5.8 As-implemented cabling documentation . 19
A.6 Installation verification and installation acceptance test . 19
A.6.1 General . 19
A.6.2 Installation verification . 19
A.6.3 Installation acceptance test . 19
A.7 Installation administration . 20
A.8 Installation maintenance and installation troubleshooting . 20

Figure 1 – Standards relationships . 6

Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet . 11
Table A.2 – Basic network characteristics for un-balanced cabling not based on
Ethernet . 12
Table A.3 – Information relevant to copper cable: fixed cables . 13
Table A.4 – Connectors for copper cabling CPs not based on Ethernet – twisted pair . 14

Table A.5 – Connectors for copper cabling CPs not based on Ethernet – Coaxial cable . 14
Table A.6 – Parameters for balanced cables – twisted pair . 17
Table A.7 – Parameters for un-balanced cables – coaxial cable . 17

– 4 – IEC 61784-5-22:2024 © IEC 2024
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
INDUSTRIAL NETWORKS –
PROFILES –
Part 5-22: Installation of fieldbuses –
Installation profiles for CPF 22

FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international
co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and
in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports,
Publicly Available Specifications (PAS) and Guides (hereafter referred to as "IEC Publication(s)"). Their
preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with
may participate in this preparatory work. International, governmental and non-governmental organizations liaising
with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for
Standardization (ISO) in accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence between
any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity
assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any
services carried out by independent certification bodies.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) IEC draws attention to the possibility that the implementation of this document may involve the use of (a)
patent(s). IEC takes no position concerning the evidence, validity or applicability of any claimed patent rights in
respect thereof. As of the date of publication of this document, IEC had not received notice of (a) patent(s), which
may be required to implement this document. However, implementers are cautioned that this may not represent
the latest information, which may be obtained from the patent database available at https://patents.iec.ch. IEC
shall not be held responsible for identifying any or all such patent rights. IEC shall not be held responsible for
identifying any or all such patent rights.
IEC 61784-5-22 has been prepared by subcommittee 65C: Industrial networks, of IEC technical
committee 65: Industrial-process measurement, control and automation. It is an International
Standard.
This document is to be used in conjunction with IEC 61918:2018, IEC 61918:2018/AMD1:2022
and IEC 61918:2018/AMD2:2024.
The text of this International Standard is based on the following documents:
Draft Report on voting
65C/1279/FDIS 65C/1293/RVD
Full information on the voting for its approval can be found in the report on voting indicated in
the above table.
The language used for the development of this International Standard is English.
This document was drafted in accordance with the ISO/IEC Directives, Part 2, and developed
in accordance with ISO/IEC Directives, Part 1 and ISO/IEC Directives, IEC Supplement,
available at www.iec.ch/members_experts/refdocs. The main document types developed by IEC
are described in greater detail at www.iec.ch/publications.
A list of all parts of IEC 61784-5 series, published under the general title Industrial networks –
Profiles – Installation of fieldbuses, can be found on the IEC website.
The committee has decided that the contents of this document will remain unchanged until the
stability date indicated on the IEC website under webstore.iec.ch in the data related to the
specific document. At this date, the document will be
• reconfirmed,
• withdrawn, or
• revised.
IMPORTANT – The "colour inside" logo on the cover page of this document indicates
that it contains colours which are considered to be useful for the correct understanding
of its contents. Users should therefore print this document using a colour printer.

– 6 – IEC 61784-5-22:2024 © IEC 2024
INTRODUCTION
This document is one of a series produced to facilitate the use of communication networks in
industrial control systems.
IEC 61918:2018 and IEC 61918:2018/AMD1:2022 and IEC 61918:2018/AMD2:2024 provide the
common requirements for the installation of communication networks in industrial control
systems. This installation profile document provides the installation profiles of the
communication profiles (CP) of a specific communication profile family (CPF) by stating which
requirements of IEC 61918 fully apply and, where necessary, by supplementing, modifying, or
replacing the other requirements (see Figure 1).
For general background on fieldbuses, their profiles, and relationship between the installation
profiles specified in this document, see IEC 61158-1.
Each CP installation profile is specified in a separate annex of this document. Each annex is
structured exactly as the reference standard IEC 61918 for the benefit of the persons
representing the roles in the fieldbus installation process as defined in IEC 61918 (planner,
installer, verification personnel, validation personnel, maintenance personnel, administration
personnel). By reading the installation profile in conjunction with IEC 61918, these persons
immediately know which requirements are common for the installation of all CPs and which are
modified or replaced. The conventions used to draft this document are defined in Clause 5.
The provision of the installation profiles in one document for each CPF (for example
IEC 61784-5-22 for CPF 22) allows readers to work with documents of a convenient size.

Figure 1 – Standards relationships

INDUSTRIAL NETWORKS –
PROFILES –
Part 5-22: Installation of fieldbuses –
Installation profiles for CPF 22

1 Scope
This part of IEC 61784-5 specifies the installation profile for CPF 22 (AUTBUS™ ).
The installation profile is specified in Annex A. This annex is read in conjunction with
IEC 61918:2018, IEC 61918:2018/AMD1:2022 and IEC 61918:2018/AMD2:2024.
2 Normative references
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies.
For undated references, the latest edition of the referenced document (including any
amendments) applies.
IEC 61918:2018 , Industrial communication networks – Installation of communication networks
in industrial premises
IEC 61918:2018/AMD1:2022
IEC 61918:2018/AMD2:2024
NOTE For profile specific normative references, see Clause A.2.
3 Terms, definitions and abbreviated terms
For the purposes of this document, the terms, definitions and abbreviated terms given in
IEC 61918:2018, Clause 3 and IEC 61918:2018/AMD1:2022, Clause 3, apply.
ISO and IEC maintain terminology databases for use in standardization at the following
addresses:
• IEC Electropedia: available at https://www.electropedia.org/
• ISO Online browsing platform: available at https://www.iso.org/obp
4 CPF 22: Overview of installation profiles
CPF 22 consists of one communication profile as specified in IEC 61784-1:2023.
The installation requirements for CP 22/1 (AUTBUS™) are specified in Annex A.
___________
1 TM
AUTBUS is the trade name of the Kyland Technology Co., Ltd. This information is given for the convenience
of users of this document and does not constitute an endorsement by IEC of the trademark holder or any of its
products. Compliance does not require use of the trade name. Use of the trade name requires permission of
Kyland Technology Co., Ltd.
The normative references of IEC 61918:2018, Clause 2, IEC 61918:2018/AMD1:2022, Clause 2 and
IEC 61918:2018/AMD2:2024, Clause 2, apply.

– 8 – IEC 61784-5-22:2024 © IEC 2024
5 Installation profile conventions
The numbering of the clauses and subclauses in Annex A of this document corresponds to the
numbering of IEC 61918 main clauses and subclauses.
The annex clauses and subclauses of this document supplement, modify, or replace the
respective clauses and subclauses in IEC 61918.
Where there is no corresponding subclause of IEC 61918 in Annex A in this document, the
subclause of IEC 61918 applies without modification.
The annex heading letter represents the installation profile assigned in Clause 4. The annex
(sub)clause numbering following the annex letter shall represent the corresponding (sub)clause
numbering of IEC 61918.
EXAMPLE Subclause A.4.4 in IEC 61784-5-22 means that CP 22/1 specifies the Subclause 4.4 of IEC 61918.
All main clauses of IEC 61918 are cited and apply in full unless otherwise stated in each
normative installation profile annex.
If all subclauses of a (sub)clause are omitted, then the corresponding IEC 61918 (sub)clause
apply.
If in a (sub)clause it is written "Not applicable", then the corresponding IEC 61918 (sub)clause
does not apply.
If in a (sub)clause it is written "Addition:", then the corresponding IEC 61918 (sub)clause
applies with the additions written in the profile.
If in a (sub)clause it is written "Replacement:", then the text provided in the profile replaces the
text of the corresponding IEC 61918 (sub)clause.
NOTE A replacement can also comprise additions.
If in a (sub)clause it is written "Modification:", then the corresponding IEC 61918 (sub)clause
applies with the modifications written in the profile.
If all (sub)clauses of a (sub)clause are omitted but in this (sub)clause it is written "(Sub)clause
x has addition:" (or "replacement:") or "(Sub)clause x is not applicable.", then (sub)clause x
becomes valid as declared and all the other corresponding IEC 61918 (sub)clauses apply.
6 Conformance to installation profiles
Each installation profile within this document includes part of the IEC 61918:2018 and
IEC 61918:2018/AMD1:2022. It may also include defined additional specifications.
A statement of compliance with an installation profile of this document shall be stated as either
Compliance with IEC 61784-5-22:2024 for CP 22/m or
Compliance with IEC 61784-5-22 (Ed.1) for CP 22/m .
___________
In accordance with ISO/IEC Directives.

where the name within the angle brackets < > is optional and the angle brackets shall not be
included. The m within CP 22/m shall be replaced by the profile number 1.
NOTE The name can be the name of the profile, for example AUTBUS.
If the name is a trade name, then the permission of the trade name holder shall be required.
Product standards shall not include any conformity assessment aspects (including quality
management provisions), neither normative nor informative, other than provisions for product
testing (evaluation and examination).

– 10 – IEC 61784-5-22:2024 © IEC 2024
Annex A
(normative)
CP 22/1 (AUTBUS™) specific installation profile
A.1 Installation profile scope
Addition:
This annex specifies the installation profile for Communication Profile CP 22/1 (AUTBUS™).
The CP 22/1 is specified in IEC 61784-1-22.
A.2 Normative references
Addition:
IEC 61784-1-22, Industrial networks – Profiles – Part 1-22: Fieldbus profiles – Communication
Profile Family 22
A.3 Installation profile terms, definitions, and abbreviated terms
A.3.1 Terms and definitions
A.3.2 Abbreviated terms
A.3.3 Conventions for installation profiles
Not applicable.
A.4 Installation planning
A.4.1 General
Subclause 4.1.2 has addition:
Generic cabling in accordance with ISO/IEC 11801-3 is not suitable for the cabling of CP 22/1
networks.
A.4.2 Planning requirements
A.4.2.1 Safety
Subclause 4.2.1.3 has addition:
Each and every device on CP 22/1 network should provide manufacturer's declaration stating
compliance with CP 22/1 specification.
Subclause 4.2.1.5 is not applicable.
A.4.2.2 Security
A.4.2.3 Environmental considerations and EMC
A.4.2.4 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.3 Network capabilities
A.4.3.1 Network topology
Subclause 4.3.1.2 has addition:
Bus or ring topology apply to CP 22/1 fieldbus network.
Subclause 4.3.1.5 is not applicable.
A.4.3.2 Network characteristics
A.4.3.2.1 General
A.4.3.2.2 Network characteristics for balanced cabling not based on Ethernet
Replacement:
Table A.1 provides values based on the template given in IEC 61918:2018, Table 1.
Table A.1 – Basic network characteristics for balanced cabling not based on Ethernet
Characteristic CP 22/1
Basic transmission technology Type 28
Length / transmission speed Segment length
m
30,208 Mbit/s – 103,936 Mbit/s 500
Maximum capacity Max. No.
Devices/segment 254
Devices/network 254
A.4.3.2.3 Network characteristics for balanced cabling based on Ethernet
Not applicable.
A.4.3.2.4 Network characteristics for optical fibre cabling
Not applicable.
A.4.3.2.5 Specific network characteristics
Addition:
Table A.2 provides values based on the template given in IEC 61918:2018, Table 1.

– 12 – IEC 61784-5-22:2024 © IEC 2024
Table A.2 – Basic network characteristics for
un-balanced cabling not based on Ethernet
Characteristic CP 22/1
Basic transmission technology Type 28
Segment length
Length / transmission speed
m
30,208 Mbit/s – 103,936 Mbit/s 500
Maximum capacity Max. No.
Devices/segment 254
Devices/network 254
A.4.3.2.6 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4 Selection and use of cabling components
A.4.4.1 Cable selection
A.4.4.1.1 Common description
Addition:
Generic cabling in accordance with ISO/IEC 11801-3 is not suitable for the cabling of CP 22/1
networks.
A.4.4.1.2 Copper cables
A.4.4.1.2.1 Balanced cables for Ethernet-based CPs
Not applicable.
A.4.4.1.2.2 Copper cables for non-Ethernet-based CPs
Addition:
Unshielded twisted cables shall not be used with CP 22/1 networks.
Replacement:
Table A.3 provides values based on the template given in IEC 61918:2018, Table 4.

Table A.3 – Information relevant to copper cable: fixed cables
Characteristic CP 22/1 Twisted pairs CP 22/1 coaxial cable
Nominal impedance of cable (tolerance) 100 Ω to 120 Ω, f = 0 MHz to 50 Ω ± 2 %, f = 0 MHz to 50 MHz
50 MHz
Balanced or unbalanced Balanced Un-balanced
DCR of conductors < 55 Ω /Km
DCR of shield –
Number of conductors 3 2
Shielding Mandatory -
Colour code for conductor –
Jacket colour requirements –
Jacket material Application dependent
Resistance to harsh environment (e.g. –
UV, oil resist, LS0H)
Agency ratings Application dependent
Capacitance < 50 pF/m < 100 pF/m
Velocity factor > 60 % > 70 %
Frequency band > 50 MHz
Attenuation 30 dB/100 m at 100 MHz
Withstand voltage 500 VMS
A.4.4.1.3 Cables for wireless installation
Not applicable.
A.4.4.1.4 Optical fibre cables
Not applicable.
A.4.4.1.5 Special purpose balanced and optical fibre cables
Not applicable.
A.4.4.1.6 Specific requirements for CPs
Not applicable.
A.4.4.1.7 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4.2 Connecting hardware selection
A.4.4.2.1 Common description
A.4.4.2.2 Connecting hardware for balanced cabling CPs based on Ethernet
Not applicable.
A.4.4.2.3 Connecting hardware for copper cabling CPs not based on Ethernet
Replacement:
Table A.4, Table A.5 provide values based on the template given in IEC 61918:2018, Table 8.

– 14 – IEC 61784-5-22:2024 © IEC 2024
Table A.4 – Connectors for copper cabling CPs not based on Ethernet – twisted pair
IEC
60807-2 IEC ANSI/(NFPA)
IEC 61076-2-101 Others
or IEC 61169-8 T3.5.29 R1-2007
60807-3
IEC 63
M12-5 M12-5 7/8-16
M12-n with Coaxial Open Terminal 171-
Sub-D with A- with B- M 18 UN-2B
X-coding (BNC) style block 2/IEC 6
coding coding THD
3171-5
CP
No No No No No No No No Yes Yes
22/1
NOTE For M12-5 connectors, there are many applications using these connectors that are not compatible and
when mixed can cause damage to the applications.

Table A.5 – Connectors for copper cabling CPs not based on Ethernet – Coaxial cable
IEC
60807-2 IEC ANSI/(NFPA)
IEC 61076-2-101 Others
or IEC 61169-8 T3.5.29 R1-2007
60807-3
M12-5 M12-5 7/8-16
M12-n with Coaxial Open Terminal
Sub-D with A- with B- M 18 UN-2B Others
X-coding (BNC) style block
coding coding THD
CP
No No No Yes Yes No No No No No
22/1
A.4.4.2.4 Connecting hardware wireless installation
Not applicable.
A.4.4.2.5 Connecting hardware for optical fibre cabling
Not applicable.
A.4.4.2.6 Specific requirements for CPs
Not applicable.
A.4.4.2.7 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4.3 Connections within a channel/permanent link
A.4.4.3.1 Common description
A.4.4.3.2 Balanced cabling connections and splices for CPs based on Ethernet
Not applicable.
A.4.4.3.3 Copper cabling connections and splices for CPs not based on Ethernet
A.4.4.3.3.1 Common description
Addition:
Refer to the manufacturer's data sheet regarding the number of allowed connections.
A.4.4.3.3.2 Connections minimum distance

A.4.4.3.3.3 Copper cabling splices
Not applicable.
A.4.4.3.3.4 Copper cabling bulkhead connections
Not applicable.
A.4.4.3.3.5 Copper cabling J-J couplers (J-J adaptors)
Not applicable.
A.4.4.3.4 Optical fibre cabling connections and splices for CPs based on Ethernet
Not applicable.
A.4.4.3.5 Optical fibre cabling connections and splices for CPs not based on
Ethernet
Not applicable.
A.4.4.3.6 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4.4 Terminators
A.4.4.4.1 Common description
Addition:
For CP 22/1 networks bus topology, terminators shall be used at each end of a network segment.
No terminator is needed for ring topology.
A.4.4.4.2 Specific requirements for CPs
Addition:
For CP 22/1 networks, in bus topology, the terminators allowed values:
Twisted pair: R = 100 Ω to 120 Ω
Coaxial cable: R = 50 Ω ± 2 %
A.4.4.4.3 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4.5 Device location and connection
Subclause 4.4.5.2 is not applicable.
Subclause 4.4.5.3 is not applicable.
A.4.4.6 Coding and labelling
Subclause 4.4.6.3 is not applicable.
Subclause 4.4.6.4 is not applicable.

– 16 – IEC 61784-5-22:2024 © IEC 2024
A.4.4.7 Earthing and bonding of equipment and devices and shielded cabling
A.4.4.7.1 Common description
A.4.4.7.2 Bonding and earthing of enclosures and pathways
A.4.4.7.3 Earthing methods
Subclause 4.4.7.3.1 is not applicable.
A.4.4.7.4 Shield earthing
A.4.4.7.4.1 Non-earthing or parallel RC
Not applicable.
A.4.4.7.4.2 Direct
A.4.4.7.4.3 Derivatives of direct and parallel RC
Not applicable.
A.4.4.7.5 Specific requirements for CPs
Not applicable.
A.4.4.7.6 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.4.4.8 Storage and transportation of cables
Subclause 4.4.8.2 is not applicable.
A.4.4.9 Routing of cables
A.4.4.10 Separation of circuits
Addition:
The cabling outside of enclosure shall be separated in accordance with manufacturer’s
installation instructions.
A.4.4.11 Mechanical protection of cabling components
Subclause 4.4.11.2 is not applicable.
A.4.4.12 Installation in special areas
Subclause 4.4.12.2 is not applicable.
A.4.5 Cabling planning documentation
A.4.6 Verification of cabling planning specification
A.5 Installation implementation
A.5.1 General requirements
Subclause 5.1.3 is not applicable.

A.5.2 Cable installation
A.5.2.1 General requirements for all cabling types
Subclause 5.2.1.2 has replacement:
Table A.6, Table A.7 provide values based on the template given in IEC 61918:2018, Table 18.
Table A.6 – Parameters for balanced cables – twisted pair
Characteristic Value
a
Minimum bending radius, single bending

(mm)
a
Bending radius, multiple bending (mm)

Mechanical a
Pull forces (N)
force
a
Permanent tensile forces (N)
a
Maximum lateral forces (N/cm)
a
Temperature range during installation (°C)

a
Depending on cable type; see manufacturer’s data sheet

Table A.7 – Parameters for un-balanced cables – coaxial cable
Characteristic Value
a
Minimum bending radius, single bending

(mm)
a
Bending radius, multiple bending (mm)

Mechanical a
Pull forces (N)
force
a
Permanent tensile forces (N)
a
Maximum lateral forces (N/cm)
a
Temperature range during installation (°C)

a
Depending on cable type; see manufacturer’s data sheet

Subclause 5.2.1.12 is not applicable
A.5.2.2 Installation and routing
A.5.2.3 Specific requirements for CPs
Not applicable.
A.5.2.4 Specific requirements for wireless installation
Not applicable.
A.5.2.5 Specific requirements for generic cabling in accordance with
ISO/IEC 11801-3
A.5.3 Connector installation
Subclause 5.3.4 is not applicable.
Subclause 5.3.5 is not applicable.

– 18 – IEC 61784-5-22:2024 © IEC 2024
A.5.4 Terminator installation
A.5.4.1 Common description
A.5.4.2 Specific requirements for CPs
Addition:
For CP 22/1, in bus topology, both ends of a network shall be terminated with a resistor
terminator, and 100 Ω to 120 Ω resistors should be used for twisted pair cable and 50 Ω ± 2 %
resistors for coaxial cable.
A.5.5 Device installation
Subclause 5.5.2 is not applicable.
A.5.6 Coding and labelling
Subclause 5.6.2 is not applicable.
A.5.7 Earthing and bonding of equipment and devices and shield cabling
A.5.7.1 Common description
A.5.7.2 Bonding and earthing of enclosures and pathways
A.5.7.3 Earthing methods
A.5.7.3.1 Equipotential
Not applicable.
A.5.7.3.2 Star
A.5.7.3.3 Earthing of equipment (devices)
A.5.7.3.3.1 Non-earthing or parallel RC
Not applicable.
A.5.7.3.3.2 Direct
A.5.7.3.3.3 Installing copper bus bars
A.5.7.4 Shield earthing methods
A.5.7.4.1 General
A.5.7.4.2 Parallel RC
Not applicable.
A.5.7.4.3 Direct
A.5.7.4.4 Derivatives of direct and parallel RC
Not applicable.
A.5.7.5 Specific requirements for CPs
Not applicable.
A.5.7.6 Specific requirements for generic cabling in accordance with
ISO/IEC 11801‑3
A.5.8 As-implemented cabling documentation
A.6 Installation verification and installation acceptance test
A.6.1 General
A.6.2 Installation verification
A.6.2.1 General
A.6.2.2 Verification according to cabling planning documentation
A.6.2.3 Verification of earthing and bonding
Subclause 6.2.3.2 is not applicable.
A.6.2.4 Verification of shield earthing
A.6.2.5 Verification of cabling system
A.6.2.6 Cable selection verification
Subclause 6.2.6.2 is not applicable.
A.6.2.7 Connector verification
Subclause 6.2.7.2 is not applicable.
A.6.2.8 Connection verification
A.6.2.9 Terminator verification
Subclause 6.2.9.2 is not applicable.
A.6.2.10 Coding and labelling verification
Subclause 6.2.10.2 is not applicable.
A.6.2.11 Verification report
A.6.3 Installation acceptance test
A.6.3.1 General
A.6.3.2 Acceptance test of Ethernet-based cabling
Not applicable.
A.6.3.3 Acceptance test of non-Ethernet-based cabling
Subclause 6.3.3.2 is not applicable.
A.6.3.4 Specific requirements for wireless installation
Not applicable.
– 20 – IEC 61784-5-22:2024 © IEC 2024
A.6.3.5 Acceptance test report
A.7 Installation administration
Subclause 7.8 is not applicable.
A.8 Installation maintenance and installation troubleshooting
Subclause 8.4 is not applicable.

___________
– 22 – IEC 61784-5-22:2024 © IEC 2024
SOMMAIRE
AVANT-PROPOS . 24
INTRODUCTION . 26
1 Domaine d’application . 27
2 Références normatives . 27
3 Termes, définitions et termes abrégés . 27
4 CPF 22: vue d’ensemble des profils d’installation . 28
5 Conventions relatives aux profils d’installation . 28
6 Conformité aux profils d’installation . 29
Annexe A (normative) Profil d’installation spécifique au CP 22/1 (AUTBUS™) . 30
A.1 Domaine d’application du profil d’installation . 30
A.2 Références normatives . 30
A.3 Termes, définitions et termes abrégés utilisés pour le profil d’installation . 30
A.3.1 Termes et définitions . 30
A.3.2 Termes abrégés. 30
A.3.3 Conventions relatives aux profils d’installation . 30
A.4 Planification de l’installation . 30
A.4.1 Généralités . 30
A.4.2 Exigences de planification . 30
A.4.3 Capacités du réseau . 31
A.4.4 Sélection et utilisation de composants de câblage . 32
A.4.5 Documentation de planification du câblage . 37
A.4.6 Vérification de la spécification de planification du câblage . 37
A.5 Mise en œuvre de l’installation . 37
A.5.1 Exigences générales . 37
A.5.2 Installation des câbles . 37
A.5.3 Installation de connecteur . 38
A.5.4 Installation des terminaisons . 38
A.5.5 Installation du dispositif . 38
A.5.6 Codage et étiquetage . 38
A.5.7 Mise à la terre et équipotentialité du matériel et des dispositifs et
câblage blindé . 39
A.5.8 Documentation du câblage comme exécuté . 39
A.6 Installation, vérification et essai de réception de l’installation . 39
A.6.1 Généralités . 39
A.6.2 Vérification de l’installation . 39
A.6.3 Essai de réception de l’installation . 40
A.7 Administration de l’installation . 40
A.8 Maintenance et dépannage de l’installation . 40

Figure 1 – Relations entre les normes . 26

Tableau A.1 – Caractéristiques de base du réseau pour un câblage symétrique ne
reposant pas sur Ethernet . 31
Tableau A.2 – Caractéristiques de base du réseau pour un câblage symétrique ne
reposant pas sur Ethernet . 32
Tableau A.3 – Informations applicables aux câbles en cuivre: câbles fixes . 33

Tableau A.4 – Connecteurs pour les CP de câblage en cuivre ne reposant pas sur
Ethernet – paires torsadées . 34
Tableau A.5 – Connecteurs pour les CP de câblage en cuivre ne reposant pas sur

Ethernet – câble coaxial. 34
Tableau A.6 – Paramètres pour câbles symétriques – paires torsadées . 37
Tableau A.7 – Paramètres pour câbles non symétriques – câble coaxial . 38

– 24 – IEC 61784-5-22:2024 © IEC 2024
COMMISSION ÉLECTROTECHNIQUE INTERNATIONALE
____________
RÉSEAUX INDUSTRIELS –
PROFILS –
Partie 5-22: Installation des bus de terrain –
Profils d’installation pour CPF 22

AVANT-PROPOS
1) La Commission Électrotechnique Internationale (IEC) est une organisation mondiale de normalisation composée
de l’ensemble des comités électrotechniques nationaux (Comités nationaux de l’IEC). L’IEC a pour objet de
favoriser la coopération internationale pour toutes les questions de normalisation dans les domaines de
l’électricité et de l’électronique. À cet effet, l’IEC – entre autres activités – publie des Normes internationales,
des Spécifications techniques, des Rapports techniques, des Spécifications accessibles au public (PAS) et des
Guides (ci-après dénommés "Publication(s) de l’IEC"). Leur élaboration est confiée à des comités d’études, aux
travaux desquels tout Comité national intéressé par le sujet traité peut participer. Les organisations
internationales, gouv
...