IEC 60076-21:2011
(Main)Power transformers - Part 21: Standard requirements, terminology, and test code for step-voltage regulators
Power transformers - Part 21: Standard requirements, terminology, and test code for step-voltage regulators
IEC 60076-21:2011/IEEE Std C57.15:2009 - Description of design types, tables of 50 Hz and 60 Hz ratings, supplementary ratings, construction, and available accessories are provided. Methods for performing routine and design tests applicable to liquid-immersed single and three-phase step-voltage regulators are described. Winding resistance measurements, polarity tests, insulation power factor and resistance tests, ratio tests, no load loss and excitation current measurements, impedance and load loss measurements, dielectric tests, temperature tests, routine and design impulse tests, short-circuit tests, control tests, calculated data, and certified test data are covered.
General Information
Relations
Standards Content (Sample)
IEC 60076-21
Edition 1.0 2011-12
™
IEEE Std C57.15
INTERNATIONAL
STANDARD
Power transformers –
Part 21: Standard requirements, terminology, and test code for step-voltage
regulators
IEC 60076-21:2011(E) IEEE Std. C57.15-2009
---------------------- Page: 1 ----------------------
THIS PUBLICATION IS COPYRIGHT PROTECTED
Copyright © 2009 IEEE
All rights reserved. IEEE is a registered trademark in the U.S. Patent & Trademark Office, owned by the Institute of
Electrical and Electronics Engineers, Inc.
Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from the IEC Central Office.
Any questions about IEEE copyright should be addressed to the IEEE. Enquiries about obtaining additional rights
to this publication and other information requests should be addressed to the IEC or your local IEC member National
Committee.
IEC Central Office The Institute of Electrical and Electronics Engineers, Inc
3, rue de Varembé 3 Park Avenue
CH-1211 Geneva 20 US-New York, NY10016-5997
Switzerland USA
Email: inmail@iec.ch Email: stds-info@ieee.org
Web: www.iec.ch Web: www.ieee.org
About the IEC
The International Electrotechnical Commission (IEC) is the leading global organization that prepares and publishes
International Standards for all electrical, electronic and related technologies.
About IEC publications
The technical content of IEC publications is kept under constant review by the IEC. Please make sure that you have the
latest edition, a corrigenda or an amendment might have been published.
Catalogue of IEC publications: www.iec.ch/searchpub
The IEC on-line Catalogue enables you to search by a variety of criteria (reference number, text, technical committee,…).
It also gives information on projects, withdrawn and replaced publications.
IEC Just Published: www.iec.ch/online_news/justpub
Stay up to date on all new IEC publications. Just Published details twice a month all new publications released. Available
on-line and also by email.
Electropedia: www.electropedia.org
The world's leading online dictionary of electronic and electrical terms containing more than 20 000 terms and definitions
in English and French, with equivalent terms in additional languages. Also known as the International Electrotechnical
Vocabulary online.
Customer Service Centre: www.iec.ch/webstore/custserv
If you wish to give us your feedback on this publication or need further assistance, please visit the Customer Service
Centre FAQ or contact us:
Email: csc@iec.ch
Tel.: +41 22 919 02 11
---------------------- Page: 2 ----------------------
IEC 60076-21
Edition 1.0 2011-12
™
IEEE Std C57.15
INTERNATIONAL
STANDARD
Power transformers –
Part 21: Standard requirements, terminology, and test code for step-voltage
regulators
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
XD
ICS 29.180 ISBN 978-2-88912-848-8
---------------------- Page: 3 ----------------------
– i – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
Contents
1. Overview . 1
1.1 Scope . 1
1.2 Purpose . 1
1.3 Word usage . 1
2. Normative references . 2
3. Definitions . 3
4. Service conditions . 9
4.1 Usual service conditions . 9
4.2 Loading at other than rated conditions .10
4.3 Unusual service conditions .10
4.4 Frequency .12
5. Rating data .12
5.1 Cooling classes of voltage regulators .12
5.2 Ratings .13
5.3 Supplementary continuous-current ratings .17
5.4 Taps .18
5.5 Operating voltage limits .18
5.6 Voltage supply ratios .20
5.7 Insulation levels .20
5.8 Losses .21
5.9 Short-circuit requirements .22
5.10 Tests .23
6. Construction .24
6.1 Bushings .24
6.2 Terminal markings .25
6.3 Diagram of connections .26
6.4 Nameplates .26
6.5 Tank construction .27
6.6 Components and accessories .31
7. Other requirements .32
7.1 Other supplementary continuous-current ratings .32
7.2 Other components and accessories .32
8. Test code.33
8.1 Resistance measurements .34
8.2 Polarity test .36
8.3 Ratio tests .37
8.4 No-load losses and excitation current .40
8.5 Load losses and impedance voltage .45
8.6 Dielectric tests .51
8.7 Temperature-rise tests .64
8.8 Short-circuit tests .73
8.9 Calculated data .77
9. Control systems .81
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 4 ----------------------
IEC 60076-21:2011(E) – ii –
IEEE Std C57.15-2009
9.1 General .81
9.2 Control device construction .81
9.3 Control system requirements .82
9.4 Tests .83
Annex A (informative) Unusual temperature and altitude conditions .87
Annex B (informative) Field dielectric tests.89
Annex C (informative) Bibliography.90
Annex D (informative) IEEE List of Participants .92
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 5 ----------------------
– iii – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
POWER TRANSFORMERS –
Part 21: Standard requirements, terminology,
and test code for step-voltage regulators
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization
comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to
promote international co-operation on all questions concerning standardization in the electrical and
electronic fields. To this end and in addition to other activities, IEC publishes International Standards,
Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides
(hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any
IEC National Committee interested in the subject dealt with may participate in this preparatory work.
International, governmental and non-governmental organizations liaising with the IEC also participate in
this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in
accordance with conditions determined by agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an
international consensus of opinion on the relevant subjects since each technical committee has
representation from all interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC
National Committees in that sense. While all reasonable efforts are made to ensure that the technical
content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are
used or for any misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly
indicated in the latter.
5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide
conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not
responsible for any services carried out by independent certification bodies.
6) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject
of patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 60076-21/IEEE Std C57.15 has been processed through IEC
technical committee 14: Power transformers.
The text of this standard is based on the following documents:
IEEE Std FDIS Report on voting
C57.15-2009 14/688/FDIS 14/697/RVD
Full information on the voting for the approval of this standard can be found in the report
on voting indicated in the above table.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 6 ----------------------
IEC 60076-21:2011(E) – iv –
IEEE Std C57.15-2009
A list of all the parts in the IEC 60076 series, published under the general title Power
transformers can be found on the IEC website.
The committee has decided that the contents of this publication will remain unchanged
until the stability date indicated on the IEC web site under "http://webstore.iec.ch" in the
data related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 7 ----------------------
– v – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
IEC/IEEE Dual Logo International Standards
This Dual Logo International Standard is the result of an agreement between the IEC and the Institute of
Electrical and Electronics Engineers, Inc. (IEEE). The original IEEE Standard was submitted to the IEC for
consideration under the agreement, and the resulting IEC/IEEE Dual Logo International Standard has been
published in accordance with the ISO/IEC Directives.
IEEE Standards documents are developed within the IEEE Societies and the Standards Coordinating
Committees of the IEEE Standards Association (IEEE-SA) Standards Board. The IEEE develops its standards
through a consensus development process, approved by the American National Standards Institute, which
brings together volunteers representing varied viewpoints and interests to achieve the final product.
Volunteers are not necessarily members of the Institute and serve without compensation. While the IEEE
administers the process and establishes rules to promote fairness in the consensus development process, the
IEEE does not independently evaluate, test, or verify the accuracy of any of the information contained in its
standards.
Use of an IEC/IEEE Dual Logo International Standard is wholly voluntary. The IEC and IEEE disclaim liability
for any personal injury, property or other damage, of any nature whatsoever, whether special, indirect,
consequential, or compensatory, directly or indirectly resulting from the publication, use of, or reliance upon
this, or any other IEC or IEEE Standard document.
The IEC and IEEE do not warrant or represent the accuracy or content of the material contained herein, and
expressly disclaim any express or implied warranty, including any implied warranty of merchantability or
fitness for a specific purpose, or that the use of the material contained herein is free from patent
infringement. IEC/IEEE Dual Logo International Standards documents are supplied “AS IS”.
The existence of an IEC/IEEE Dual Logo International Standard does not imply that there are no other ways
to produce, test, measure, purchase, market, or provide other goods and services related to the scope of the
IEC/ IEEE Dual Logo International Standard. Furthermore, the viewpoint expressed at the time a standard is
approved and issued is subject to change brought about through developments in the state of the art and
comments received from users of the standard.
Every IEEE Standard is subjected to review at least every five years for revision or reaffirmation. When a
document is more than five years old and has not been reaffirmed, it is reasonable to conclude that its
contents, although still of some value, do not wholly reflect the present state of the art. Users are cautioned
to check to determine that they have the latest edition of any IEEE Standard.
In publishing and making this document available, the IEC and IEEE are not suggesting or rendering
professional or other services for, or on behalf of, any person or entity. Neither the IEC nor IEEE is
undertaking to perform any duty owed by any other person or entity to another. Any person utilizing this, and
any other IEC/IEEE Dual Logo International Standards or IEEE Standards document, should rely upon the
advice of a competent professional in determining the exercise of reasonable care in any given
circumstances.
Interpretations – Occasionally questions may arise regarding the meaning of portions of standards as they
relate to specific applications. When the need for interpretations is brought to the attention of IEEE, the
Institute will initiate action to prepare appropriate responses. Since IEEE Standards represent a consensus of
concerned interests, it is important to ensure that any interpretation has also received the concurrence of a
balance of interests. For this reason, IEEE and the members of its societies and Standards Coordinating
Committees are not able to provide an instant response to interpretation requests except in those cases
where the matter has previously received formal consideration.
Comments for revision of IEC/IEEE Dual Logo International Standards are welcome from any interested party,
regardless of membership affiliation with the IEC or IEEE. Suggestions for changes in documents should be
in the form of a proposed change of text, together with appropriate supporting comments. Comments on
standards and requests for interpretations should be addressed to:
Secretary, IEEE-SA Standards Board, 445 Hoes Lane, Piscataway, NJ 08854, USA and/or General Secretary,
IEC, 3, rue de Varembé, PO Box 131, 1211 Geneva 20, Switzerland.
Authorization to photocopy portions of any individual standard for internal or personal use is granted by the
Institute of Electrical and Electronics Engineers, Inc., provided that the appropriate fee is paid to Copyright
Clearance Center. To arrange for payment of licensing fee, please contact Copyright Clearance Center,
Customer Service, 222 Rosewood Drive, Danvers, MA 01923 USA; +1 978 750 8400. Permission to
photocopy portions of any individual standard for educational classroom use can also be obtained through the
Copyright Clearance Center.
NOTE Attention is called to the possibility that implementation of this standard may require use of subject
matter covered by patent rights. By publication of this standard, no position is taken with respect to the
existence or validity of any patent rights in connection therewith. The IEEE shall not be responsible for
identifying patents for which a license may be required by an IEEE standard or for conducting inquiries into
the legal validity or scope of those patents that are brought to its attention.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 8 ----------------------
IEC 60076-21:2011(E) – vi –
IEEE Std C57.15-2009
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 9 ----------------------
– vii – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
IEEE Standard Requirements,
Terminology, and Test Code for
Step-Voltage Regulators
Sponsor
Transformers Committee
of the
IEEE Power & Energy Society
Approved 11 September 2009
IEEE-SA Standards Board
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 10 ----------------------
IEC 60076-21:2011(E) – viii –
IEEE Std C57.15-2009
Abstract: Description of design types, tables of 50 Hz and 60 Hz ratings, supplementary ratings,
construction, and available accessories are provided. Methods for performing routine and design
tests applicable to liquid-immersed single and three-phase step-voltage regulators are described.
Winding resistance measurements, polarity tests, insulation power factor and resistance tests,
ratio tests, no load loss and excitation current measurements, impedance and load loss
measurements, dielectric tests, temperature tests, routine and design impulse tests, short-circuit
tests, control tests, calculated data, and certified test data are covered.
Keywords: control, design tests, position indicator, routine tests, series transformer, tap changer,
Type A, Type B, voltage regulator
•
National Electrical Safety Code and NESC are both registered trademarks and service marks of the Institute of Electrical
and Electronics Engineers, Inc.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 11 ----------------------
– ix – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
IEEE Introduction
This introduction is not part of IEEE Std C57.15-2009, IEEE Standard Requirements, Terminology, and Test Code for
Step-Voltage Regulators.
The Working Group has undertaken the task to update this standard to:
a) Reflect the latest revisions of referenced documents IEEE Std C57.12.00™ [B13] and
IEEE Std C57.12.90™ [B16], and eliminate references to these standards in this standard
1
IEEE Std C57.15-2009 and duplicate applicable text.
b) Adapt the new IEEE approved format to ensure compatibility with the latest ISO and IEC
standards.
c) Include references to applicable IEC standards and keep IEEE standard references to a minimum.
This assists in setting up document as a possible candidate for a dual logo (IEC/IEEE).
d) Update tables of preferred ratings; include 50 Hz ratings. Ratings of 2.4 kV (45 BIL), 46 kV
(250 BIL), and 69 kV (350 BIL) have been removed from the three-phase 60 Hz voltage regulator
rating Table 5 (Table 4 in 1999 edition) due to historical inactivity of requests from users for
ratings.
e) Add bushing terminal connectors for current ratings of 669 A to 2000 A.
f) Clarify Type A and Type B designs and their resulting voltage regulation per extreme tap positions.
g) Review short-circuit requirements for distribution and substation applications and revise where
applicable.
Notice to users
Laws and regulations
Users of these documents should consult all applicable laws and regulations. Compliance with the
provisions of this standard does not imply compliance to any applicable regulatory requirements.
Implementers of the standard are responsible for observing or referring to the applicable regulatory
requirements. IEEE does not, by the publication of its standards, intend to urge action that is not in
compliance with applicable laws, and these documents may not be construed as doing so.
Copyrights
This document is copyrighted by the IEEE. It is made available for a wide variety of both public and
private uses. These include both use, by reference, in laws and regulations, and use in private self-
regulation, standardization, and the promotion of engineering practices and methods. By making this
document available for use and adoption by public authorities and private users, the IEEE does not waive
any rights in copyright to this document.
1
The numbers in brackets correspond to those of the bibliography in Annex C.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 12 ----------------------
IEC 60076-21:2011(E) – x –
IEEE Std C57.15-2009
Updating of IEEE documents
Users of IEEE standards should be aware that these documents may be superseded at any time by the
issuance of new editions or may be amended from time to time through the issuance of amendments,
corrigenda, or errata. An official IEEE document at any point in time consists of the current edition of the
document together with any amendments, corrigenda, or errata then in effect. In order to determine whether
a given document is the current edition and whether it has been amended through the issuance of
amendments, corrigenda, or errata, visit the IEEE Standards Association web site at
http://ieeexplore.ieee.org/xpl/standards.jsp, or contact the IEEE at the address listed previously.
For more information about the IEEE Standards Association or the IEEE standards development process,
visit the IEEE-SA web site at http://standards.ieee.org.
Errata
Errata, if any, for this and all other standards can be accessed at the following URL:
http://standards.ieee.org/reading/ieee/updates/errata/index.html. Users are encouraged to check this URL
for errata periodically.
Interpretations
Current interpretations can be accessed at the following URL: http://standards.ieee.org/reading/ieee/interp/
index.html.
Patents
Attention is called to the possibility that implementation of this standard may require use of subject matter
covered by patent rights. By publication of this standard, no position is taken with respect to the existence
or validity of any patent rights in connection therewith. The IEEE is not responsible for identifying
Essential Patent Claims for which a license may be required, for conducting inquiries into the legal validity
or scope of Patents Claims or determining whether any licensing terms or conditions provided in
connection with submission of a Letter of Assurance, if any, or in any licensing agreements are reasonable
or non-discriminatory. Users of this standard are expressly advised that determination of the validity of any
patent rights, and the risk of infringement of such rights, is entirely their own responsibility. Further
information may be obtained from the IEEE Standards Association.
IMPORTANT NOTICE: This standard is not intended to ensure safety, security, health, or
environmental protection in all circumstances. Implementers of the standard are responsible for
determining appropriate safety, security, environmental, and health practices or regulatory
requirements.
This IEEE document is made available for use subject to important notices and legal disclaimers.
These notices and disclaimers appear in all publications containing this document and may
be found under the heading “Important Notice” or “Important Notices and Disclaimers
Concerning IEEE Documents.” They can also be obtained on request from IEEE or viewed at
http://standards.ieee.org/IPR/disclaimers.html.
Published by the IEC under licence from IEEE. © 2009 IEEE. All rights reserved.
---------------------- Page: 13 ----------------------
– 1 – IEC 60076-21:2011(E)
IEEE Std C57.15-2009
POWER TRANSFORMERS –
Part 21: Standard requirements,
terminology, and test code for step-
voltage regulators
1. Overview
1.1 Scope
This standard describes electrical and mechanical requirements of liquid-immersed, single- and three-
phase, step-voltage regulators, not exceeding a regulation of 3000 kVA (for three-phase units) or 1000 kVA
(for single-phase units). This standard does not apply to load tap-changing power transformers.
1.2 Purpose
This standard is intended as a basis for the establishment of performance, limited electrical and mechanical
interchangeability, and general requirements of equipment described. It also assists in the proper selection
of such equipment.
1.3 Word usage
When this standard is used on a mandatory basis, the word shall indicates mandato
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.