IEC 61300-2-46:2019/COR1:2022
(Corrigendum)Corrigendum 1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-46: Tests - Damp heat, cyclic
Corrigendum 1 - Fibre optic interconnecting devices and passive components - Basic test and measurement procedures - Part 2-46: Tests - Damp heat, cyclic
General Information
Relations
Standards Content (Sample)
IEC 2022
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
IEC 61300-2-46
Edition 2.0 2019-03
FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS –
BASIC TEST AND MEASUREMENT PROCEDURES
Part 2-46: Tests - Damp heat, cyclic
CO RRI G E NDUM 1
Figure 2 –Test – Stabilizing period
...
This May Also Interest You
IEC 61300-3-50:2025 describes the procedure to measure the crosstalk of optical signals between the ports of a multiport M x N (M input ports and N output ports) fibre optic spatial switch. This second edition cancels and replaces the first edition published in 2013. This edition constitutes a technical revision.
This edition includes the following significant technical changes with respect to the previous edition:
a) revising structure of the document.
- Standard11 pagesEnglish languagesale 15% off
- Standard12 pagesFrench languagesale 15% off
- Standard23 pagesEnglish and French languagesale 15% off
IEC 61300-3-7: 2025 Amendment 1
- Standard2 pagesEnglish languagesale 15% off
IEC 61300-3-7:2021 describes methods available to measure the wavelength dependence of attenuation and return loss of two-port, single mode passive optical components. It is not, however, applicable to dense wavelength division multiplexing (DWDM) devices. Measurement methods of wavelength dependence of attenuation of DWDM devices are described in IEC 61300-3-29. There are two measurement cases described in this document:
a) measurement of attenuation only;
b) measurement of attenuation and return loss at the same time.
This third edition cancels and replaces the second edition published in 2009. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) reduction of the number of alternative methods proposed to bring in-line with industry practice;
b) re-statement of the equations for insertion loss and return loss using logarithmic forms more common in the industry;
c) additional recommendations with respect to the creation of fibre terminations;
d) additional discussion on the characterization of the optical sources used in this document;
e) simplification of bi-directional testing;
f) removal of separate return loss only measurement procedures.
- Standard31 pagesEnglish languagesale 15% off
- Standard62 pagesEnglish languagesale 15% off
- Standard64 pagesEnglish and French languagesale 15% off
IEC 61300-3-14:2025 provides a method to measure the error and repeatability of the attenuation value settings of a variable optical attenuator (VOA). There are two control technologies for VOAs: manually controlled and electrically controlled. This document covers both VOA control technologies and also both single-mode fibres and multimode fibres VOAs. For electrically controlled VOAs, the hysteresis characteristics of attenuation are sometimes important. The hysteresis characteristics can be measured as stated in Annex B. This fourth edition cancels and replaces the third edition published in 2014.
This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
a) addition of IEC 61315, Calibration of fibre-optic power meters as normative reference;
b) addition of Clause 3 containing terms, definitions and abbreviated terms;
c) addition of notes for permission of repeatability definition with 2σ;
d) correction of error in Figure 1 a) and Figure 1 b);
e) addition of a clear statement on EF launch condition requirement for MM source;
f) change of “Detector” to “Power meter”;
g) combination of Clause 7 and Clause 8 into a new Clause 8 titled “Details to be specified and reported”;
h) addition of uncertainty considerations in Clause 7;
i) correction of error in Formula (B.3).
- Standard44 pagesEnglish languagesale 15% off
IEC TS 62627-09:2016, which is a Technical Specification, applies to passive optical devices (components). It provides the definitions which are commonly used in the generic specifications, performance standards and tests and measurement standards for passive optical devices (components) prepared by SC 86B. It has the following three types of terms and definitions:
- basic terms and definitions;
- component terms and definitions;
- performance parameter terms and definitions. The generic specifications for passive optical devices (components) are listed in Annex A.
Keywords: terms and definitions for passive optical devices
- Technical specification17 pagesEnglish languagesale 15% off
- Technical specification32 pagesEnglish languagesale 15% off
IEC TS 62629-09: 2025 Amendment 1
- Technical specification2 pagesEnglish languagesale 15% off
IEC 61300-1: 2025 Amendment 2
- Standard2 pagesEnglish languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
IEC 61300-1:2022 provides general information and guidance for the basic test and measurement procedures defined in IEC 61300-2 (all parts) and IEC 61300-3 (all parts) for interconnecting devices, passive components, mechanical splices, fusion splice protectors, fibre management systems and protective housings. This document is used in combination with the relevant specification which defines the tests to be used, the required degree of severity for each of them, their sequence, if relevant, and the permissible performance limits. In the event of conflict between this document and the relevant specification, the latter takes precedence. This fifth edition cancels and replaces the fourth edition published in 2016. This edition constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition:
- addition of the information of measurement uncertainties in 4.2.1;
- change of the requirements for attenuation variation in 4.2.2;
- addition of the multimode launch conditions of other fibres than A1-OM2, A1-OM3, A1-OM4, A1-OM5 and A3e in 10.4;
- addition of the multimode launch conditions of the planer waveguide in 10.6;
- splitting Annex A for EF and Annex B for EAF;
- correction of errors in the definitions of encircled flux and encircled angular flux.
- Standard68 pagesEnglish languagesale 15% off
- Standard70 pagesEnglish languagesale 15% off
- Standard70 pagesEnglish languagesale 15% off
- Standard45 pagesEnglish and French languagesale 15% off
IEC 61754-37:2025 defines the standard mechanical interface dimensions for the type MDC family of connectors.
- Standard24 pagesEnglish languagesale 15% off
- Standard25 pagesFrench languagesale 15% off
- Standard49 pagesEnglish and French languagesale 15% off
- Standard2 pagesEnglish languagesale 15% off
- Standard2 pagesFrench languagesale 15% off
- Standard4 pagesEnglish and French languagesale 15% off
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...