ETSI TS 101 570-2 V1.2.1 (2020-02)

TECHNICAL SPECIFICATION
Interoperability Testing for Maritime
Digital Selective Calling (DSC) Radios;
Part 2: Class A/B Test Descriptions

2 ETSI TS 101 570-2 V1.2.1 (2020-02)

Reference
RTS/ERM-TGMAR-541-2
Keywords
DSC, interoperability, maritime, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.
DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners. ®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
3 ETSI TS 101 570-2 V1.2.1 (2020-02)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definition of terms, symbols and abbreviations . 5
3.1 Terms . 5
3.2 Symbols . 6
3.3 Abbreviations . 6
4 Test Configurations . 6
5 Test Suite Structure (TSS) . 10
6 Test Descriptions (TD) VHF radios . 11
6.1 Individual Calls . 11
6.2 Group Calls . 18
6.3 All Ships Calls . 19
6.4 Sending Distress Alerts . 20
6.4.0 General Operation . 20
6.4.1 Distress alert sending priority . 24
6.4.2 Ongoing distress alert priority . 26
6.4.3 Manual termination after distress alert acknowledgement . 29
6.5 Receiving Distress Alerts . 34
6.6 Receiving Distress Alert from MOB devices . 37
6.6.1 Verifying UTC time . 37
6.6.2 Open loop automated procedures . 38
6.6.3 Closed loop automated procedures . 41
6.7 Sending Distress Relays and Acknowledgements . 45
6.8 Other calls . 46
6.9 Multiple automated procedures and parallel event handling . 48
7 MF/HF radios . 53
7.1 Individual Calls . 53
7.2 Group Calls . 62
7.3 Geographic Area Calls . 64
7.4 Sending Distress Alerts . 68
7.4.0 General Operation . 68
7.4.1 Distress alert sending priority . 73
7.4.2 Ongoing distress alert priority . 74
7.4.3 Manual termination after distress alert acknowledgement . 78
7.5 Receiving Distress Alerts . 83
7.6 Sending Distress Relays and Acknowledgements . 90
7.7 Other calls . 92
7.8 Multiple automated procedures and parallel event handling . 94
8 Interface and other functions, all radios . 99
8.1 General Tests . 99
8.2 Alarms in standby mode . 100
8.3 Alarms when busy . 107
8.4 Standby mode interface functions . 108
8.5 Timeout interface functions . 110
Annex A (informative): Bibliography . 113
History . 114

ETSI
4 ETSI TS 101 570-2 V1.2.1 (2020-02)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and
Radio spectrum Matters (ERM).
The present document is part 2 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.1].
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
5 ETSI TS 101 570-2 V1.2.1 (2020-02)
1 Scope
The present document contains the Test Descriptions (TD) for interoperability testing of the class A/B DSC radio
equipment.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 338-2: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 2: Class A/B DSC".
[2] Recommendation ITU-R M.585-8: "Assignment and use of identities in the maritime mobile
service".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 101 570-1: "Electromagnetic compatibility and Radio spectrum Matters (ERM);
Interoperability Testing for Maritime Digital Selective Calling (DSC) Radios; Part 1:
Requirements catalogue".
[i.2] ETSI EN 300 338-1: "Technical characteristics and methods of measurement for equipment for
generation, transmission and reception of Digital Selective Calling (DSC) in the maritime MF,
MF/HF and/or VHF mobile service; Part 1: Common requirements".
3 Definition of terms, symbols and abbreviations
3.1 Terms
For the purposes of the present document, the following terms apply:
class M: specific class of DSC functionality for use by man overboard devices
ETSI
6 ETSI TS 101 570-2 V1.2.1 (2020-02)
closed loop: class M individual transmission to own vessel
leap second: second which is occasionally inserted into the atomic scale of reckoning time in order to bring it into line
with solar time
open loop: class M transmitting to all ships (broadcast) 'using All ships call types'
3.2 Symbols
Void.
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in ETSI EN 300 338-1 [i.2] and the following apply:
AIS Automatic Identification System
CF (Test) ConFiguration
EUT Equipment Under Test
GNSS Global Navigation Satellite System
MOB Man OverBoard
NACK Negative ACKnowledgement
QE Qualified Equipment (i.e. DSC standards compliant)
TD Test Description
TP Test Purpose
TSS Test Suite Structure
UTC Universal Time Co-ordinated
4 Test Configurations
This clause defines all test configurations used. Each test description refers to one or multiple test configurations. It is
assumed that the initial state of all the equipment involved in the test configuration is 'standby' for DSC radios or
'deactivated' for MOB devices, i.e. unless stated otherwise the pre-test conditions of each test description assume
standby/idle mode for the equipment.
An arrow connection between devices indicates that these devices are in communication range, i.e. in CF_VHF_6 EUT,
QE1 and QE2 are all in the same communication range. However, QE3 is only in communication range with QE2.
ETSI
7 ETSI TS 101 570-2 V1.2.1 (2020-02)

Figure 1: Configurations for VHF EUT
ETSI
8 ETSI TS 101 570-2 V1.2.1 (2020-02)

Figure 2: Configurations for MF EUT
ETSI
9 ETSI TS 101 570-2 V1.2.1 (2020-02)

NOTE: HF eqipment within range receives DSC messages on every frequency band during interoperabilitytesting,
which is not always the case in real-life scenarios.

Figure 3: Configurations for HF EUT
ETSI
10 ETSI TS 101 570-2 V1.2.1 (2020-02)
5 Test Suite Structure (TSS)
The following table shows the Test Suite Structure contained in the present document. Each Test Sub-Group may
contain more than one test.
Test Group Test Sub-Group (sub-group ID)
VHF
Individual Calls (IC)
Group Calls (GC)
All Ships Calls (ASC)
Sending Distress Alerts (SDA)
Receiving Distress Alerts (RDA)
Sending Distress Relays and Acknowledgements (SDRA)
Other Calls (OC)
Multiple automated procedures and parallel event handling (MAP)
MF/HF
Individual Calls (IC)
Group Calls (GC)
Geographic Area Calls (GAC)
Sending Distress Alerts (SDA)
Receiving Distress Alerts (RDA)
Sending Distress Relays and Acknowledgements (SDRA)
Other Calls (OC)
Multiple automated procedures and parallel event handling (MAP)
Interface and other
functions (IF)
General test (GEN)
Alarms in standby mode (ASM)
Alarms when busy (AWB)
Standby mode interface functions (SMIF)
Timeout interface functions (TIF)

Each test description is described through a tabular format conforming to the following convention:
Interoperability Test Description
Identifier: A unique identifier. The test description identifiers are conforming to the
TD_DSC___ naming convention, where:
is the Test Group ID (VHF/MFHF)
is the Test Sub-Group ID
is the sequential number within the test sub-group
Summary:
Short description of the test objective
Configuration:
The relevant test configuration, referencing the test set configurations shown in figure 1
References: The reference indicates the clauses of the base standard specifications in which the related
interoperability requirement is expressed
Pre-test conditions:
Defines in which initial state the test equipment has to be to apply the actual test description
Step Test Sequence Verdict
Pass Fail
1 The description of the individual condition to verify Yes/No criteria of Yes/No criteria of
or action to perform the outcome of this the outcome of
verification step (if this verification
applicable) step (if applicable)
2 …
Final verdict:
ETSI
11 ETSI TS 101 570-2 V1.2.1 (2020-02)
6 Test Descriptions (TD) VHF radios
6.1 Individual Calls
Interoperability Test Description
Identifier:
TD_DSC_VHF_IC_0001
Summary:
'Sending Individual call - Routine'
Configuration: CF_VHF_1
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
QE1 programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of QE1
3 Verify that menu proposes an Inter-ship Channel Yes No
4 Verify if the proposed channel can be changed Yes No
5 Cause EUT to send the individual call to QE1
6 Verify that QE1 receives the call Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause QE1 to send ACK to EUT
9 Verify that EUT switches to the selected channel in step 4 Yes No
10 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0002
Summary: 'Sending Individual call with NACK - Routine'
Configuration: CF_VHF_1
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
QE1 programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of QE1
3 Verify that menu proposes an Intership Channel Yes No
4 Verify if the proposed channel can be changed Yes No
5 Cause EUT to send the individual call to QE1
6 Verify that QE1 receives the call Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause QE1 to send NACK to EUT
9 Verify that EUT does not switch to the selected channel in step 4 Yes No
10 Verify that EUT indicates 'call failed' or similar Yes No
Final verdict:
Interoperability Test Description
Identifier:
TD_DSC_VHF_IC_0003
Summary:
'Sending Individual call to a coast station - Routine'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
QE1 programmed with a Coast Station MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of QE1
3 Verify that menu does not propose a working channel Yes No
Final verdict:
ETSI
12 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0004
Summary: 'Sending Individual call - Urgency'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Urgency'
2 Enter/select MMSI of QE1
3 Set the proposed channel to CH:72
4 Cause EUT to send the individual call to QE1
5 Verify that QE1 receives the call and displays the proposed Yes No
channel
6 Verify that QE1 sounds the Urgency alarm Yes No
7 Verify that QE1 displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause QE1 to send ACK to QE1
10 Verify that EUT switches to CH:72 Yes No
11 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0005
Summary: 'Sending Individual call with NACK - Urgency'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Urgency'
2 Enter/select MMSI of QE1
3 Set the proposed channel to CH:72
4 Cause EUT to send the individual call to QE1
5 Verify that QE1 receives the call and displays the proposed Yes No
channel
6 Verify that QE1 sounds the Urgency alarm Yes No
7 Verify that QE1 displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause QE1 to send NACK to QE1
10 Verify that EUT stays on CH:16 Yes No
Final verdict:
ETSI
13 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0006
Summary: 'Sending Individual call - Safety'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Safety'
2 Enter/select MMSI of QE1
3 Set the proposed channel to CH:72
4 Cause EUT to send the individual call to QE1
5 Verify that QE1 receives the call and displays the proposed Yes No
channel
6 Verify that QE1 sounds the Safety alarm Yes No
7 Verify that QE1 displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause QE1 to send ACK to QE1
10 Verify that EUT switches to CH:72 Yes No
11 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0007
Summary: 'Sending Individual call with NACK - Safety'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Safety'
2 Enter/select MMSI of QE1
3 Set the proposed channel to CH:72
4 Cause EUT to send the individual call to QE1
5 Verify that QE1 receives the call and displays the proposed Yes No
channel
6 Verify that QE1 sounds the Safety alarm Yes No
7 Verify that QE1 displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause QE1 to send NACK to QE1
10 Verify that EUT stays on CH:16 Yes No
Final verdict:
ETSI
14 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0008
Summary: 'Receiving Individual call - Routine'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT displays the MMSI of QE1 Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause EUT to send ACK to QE1
9 Verify that EUT switches to CH:72 Yes No
10 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0009
Summary: 'Receiving Individual call with NACK - Routine'
Configuration:
CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT displays the MMSI of QE1 Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause EUT to send NACK to QE1
9 Verify that EUT is still on CH:16 Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0010
Summary: 'Receiving Individual call when busy - Routine'
Configuration:
CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions: QE1 and EUT in individual call on CH:72
QE2 programmed with an individual MMSI of EUT
Step Test Sequence Verdict
Pass Fail
1 On QE2 select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of EUT
3 Cause QE2 to send the individual call to EUT
4 Verify that EUT sounds a self-terminating alarm Yes No
5 Verify that EUT is still on CH:72 Yes No
6 Cause EUT to terminate the individual call
7 Verify that EUT displays that calls are on hold Yes No
8 On EUT enter the received call log and verify that the call from Yes No
QE2 is logged
Final verdict:
ETSI
15 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0011
Summary: 'Receiving Individual call - Urgency'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Urgency'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT sounds the Urgency alarm Yes No
7 Verify that EUT displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause EUT to send ACK to QE1
10 Verify that EUT switches to CH:72 Yes No
11 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0012
Summary:
'Receiving Individual call with NACK - Urgency'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Urgency'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT sounds the Urgency alarm Yes No
7 Verify that EUT displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause EUT to send NACK to QE1
10 Verify that EUT returns to standby on CH:16 Yes No
Final verdict:
ETSI
16 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0013
Summary: 'Receiving Individual call - Safety'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Safety'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call, sounds the Safety alarm and Yes No
displays the proposed channel
6 Verify that EUT displays the MMSI of QE1 Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause EUT to send ACK to QE1
9 Verify that EUT switches to CH:72 Yes No
10 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0014
Summary: 'Receiving Individual call with NACK - Safety'
Configuration:
CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual - Safety'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT sounds the Safety alarm Yes No
7 Verify that EUT displays the MMSI of QE1 Yes No
8 Verify that EUT is still on CH:16 Yes No
9 Cause EUT to send NACK to QE1
10 Verify that EUT returns to standby on CH:16 Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0015
Summary:
'Sending Individual call on a Distress channel'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
QE1 programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual - Routine'
2 Enter/select MMSI of QE1
3 Verify that menu proposes an Inter-ship Channel Yes No
4 Enter a distress channel as working channel
5 Cause EUT to send the individual call to QE1
6 Verify that EUT does not send the call and indicates a channel Yes No
selection error
Final verdict:
ETSI
17 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0016
Summary: 'Receiving Individual data call - Routine'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
QE1 and EUT in standby on CH:16
EUT programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Individual data'
2 Enter/select MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the individual call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT displays the MMSI of QE1 Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause EUT to send ACK to QE1
9 Verify that EUT switches to CH:72 Yes No
10 Verify the data exchange on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_IC_0017
Summary: 'Sending Individual data call - Routine'
Configuration:
CF_VHF_1
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions: QE1 and EUT in standby on CH:16
QE1 programmed with an individual MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Individual data'
2 Enter/select MMSI of QE1
3 Verify that menu proposes an Inter-ship Channel Yes No
4 Verify if the proposed channel can be changed Yes No
5 Cause EUT to send the individual call to QE1
6 Verify that QE1 receives the call Yes No
7 Verify that EUT is still on CH:16 Yes No
8 Cause QE1 to send ACK to EUT
9 Verify that EUT switches to the selected channel in step 4 Yes No
10 Verify the data exchange on this channel Yes No
Final verdict:
ETSI
18 ETSI TS 101 570-2 V1.2.1 (2020-02)
6.2 Group Calls
Interoperability Test Description
Identifier: TD_DSC_VHF_GC_0001
Summary: 'Sending group call - Routine'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1
Pre-test conditions: QE1 and EUT in standby on CH:16
QE1 programmed with a group MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Group'
2 Enter/select group MMSI of QE1
3 Verify that menu proposes an Inter-ship Channel Yes No
4 Verify if the proposed channel can be changed Yes No
5 Cause EUT to send the group call to QE1
6 Verify that QE1 receives the call Yes No
7 Verify that EUT switches to the selected channel in step 4 Yes No
8 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_GC_0002
Summary: 'Receiving group call - Routine'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1
Pre-test conditions:
QE1 and EUT in standby on CH:16
EUT programmed with a group MMSI
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'Group'
2 Enter/select group MMSI of EUT
3 Set the proposed channel to CH:72
4 Cause QE1 to send the group call to EUT
5 Verify that EUT receives the call and displays the proposed Yes No
channel
6 Verify that EUT displays the MMSI of QE1 Yes No
7 Verify that EUT switches to CH:72 Yes No
8 Verify voice communication on this channel Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_GC_0003
Summary: 'Receiving Group call when busy - Routine'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1
Pre-test conditions: QE1 and EUT in group call on CH:72
QE2 programmed with a group MMSI of EUT
Step Test Sequence Verdict
Pass Fail
1 On QE2 select 'Call' then select 'Group'
2 Enter/select group MMSI of EUT
3 Cause QE2 to send the group call to EUT
4 Verify that EUT sounds a self-terminating alarm Yes No
5 Verify that EUT is still on CH:72 Yes No
6 Cause EUT to terminate the group call
7 Verify that EUT displays that calls are on hold Yes No
8 On EUT enter the received call log and verify that the call from Yes No
QE2 is logged
Final verdict:
ETSI
19 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_GC_0004
Summary: 'Sending Group call on a Distress channel'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.6.1
Pre-test conditions:
QE1 and EUT in standby on CH:16
QE1 programmed with a group MMSI
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'Group - Routine'
2 Enter/select MMSI of QE1
3 Verify that menu proposes an Inter-ship Channel Yes No
4 Enter a distress channel as working channel
5 Cause EUT to send the group call to QE1
6 Verify that EUT does not send the call and indicates a channel Yes No
selection error
Final verdict:
6.3 All Ships Calls
Interoperability Test Description
Identifier: TD_DSC_VHF_ASC_0001
Summary: 'Sending All Ships call - Safety'
Configuration:
CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'All Ships - Safety'
2 Verify that the proposed channel is CH:16 Yes No
3 Change the proposed channel to CH:06
4 Cause EUT to send the call
5 Verify that QE1 receives the call and sounds the Safety alarm Yes No
6 Verify that QE1 displays the MMSI of the EUT Yes No
7 Verify the voice communication on CH:06 Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_ASC_0002
Summary: 'Sending All Ships call - Urgency'
Configuration: CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.6.1 and annex C
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT select 'Call' then select 'All Ships - Urgency'
2 Verify that the proposed channel is CH:16 Yes No
3 Change the proposed channel to CH:06
4 Cause EUT to send the call
5 Verify that QE1 receives the call and sounds the Urgency alarm Yes No
6 Verify that QE1 displays the MMSI of the EUT Yes No
7 Verify the voice communication on CH:06 Yes No
Final verdict:
ETSI
20 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_ASC_0003
Summary: 'Receiving All Ships call - Urgency'
Configuration: CF_VHF_3
References:
ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'All Ships - Urgency'
2 Change the proposed channel to CH:06
3 Cause QE1 to send the call
4 Verify that EUT receives the call and sounds the Urgency alarm Yes No
5 Verify that EUT displays the MMSI of QE1 Yes No
6 Verify the voice communication on CH:06 Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_ASC_0004
Summary: 'Receiving All Ships call - Safety'
Configuration:
CF_VHF_3
References: ETSI EN 300 338-2 [1], clause 6.7.1 and annex C
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On QE1 select 'Call' then select 'All Ships - Safety'
2 Change the proposed channel to CH:06
3 Cause QE1 to send the call
4 Verify that EUT receives the call and sounds the Safety alarm Yes No
5 Verify that EUT displays the MMSI of QE1 Yes No
6 Verify the voice communication on CH:06 Yes No
Final verdict:
6.4 Sending Distress Alerts
6.4.0 General Operation
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0001
Summary: 'Sending distress alert - stop before countdown'
Configuration: CF_VHF_1
References:
ETSI EN 300 338-2 [1], clause 6.4.4
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT perform action 1 for sending distress alerts
2 On EUT perform action 2 for sending distress alerts
3 Verify that action 1 and action 2 are different Yes No
4 Verify that EUT displays a countdown to sending Yes No
5 Verify that EUT sounds a countdown alarm Yes No
6 Verify the EUT gives a visible alarm Yes No
7 Stop action 2 (step 2) before countdown expires
8 Verify that QE1 does not receive a distress alert Yes No
9 Verify that EUT returns to standby Yes No
Final verdict:
ETSI
21 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0002
Summary: 'Sending distress alert - undesignated alert content'
Configuration: CF_VHF_1
References:
ETSI EN 300 338-2 [1], clause 6.4.4
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT perform action 1 for sending distress alerts
2 On EUT perform action 2 for sending distress alerts
3 Verify that action 1 and action 2 are different Yes No
4 Verify that EUT displays a countdown to sending Yes No
5 Verify that EUT sounds a countdown alarm Yes No
6 Verify the EUT gives a visible alarm Yes No
7 Continue action 2 (step 2) until countdown expires
8 Verify that QE1 receives the distress alert Yes No
9 Verify that QE1 displays the MMSI of EUT Yes No
10 Verify that QE1 displays nature of distress = undesignated Yes No
11 Verify that QE1 displays the position and time from EUT Yes No
12 Verify the voice communication between EUT and QE1 on CH:16 Yes No
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0003
Summary: 'Validation of displaying the correct alert attempt sub-stage information'
Configuration:
CF_VHF_3
References:
ETSI EN 300 338-2 [1], clauses 6.4.4, 6.4.10 and 6.5.3
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT push the Distress Button
2 Release the distress button after the countdown is complete
3 Verify that EUT briefly displays 'transmitting' sub-stage when the Yes No
countdown has completed
4 Verify that EUT displays 'waiting for acknowledgement' sub-stage Yes No
and displays the elapsed time since this sub-stage started
5 On QE1 acknowledge the EUT's alarm
6 Verify that EUT displays 'acknowledged' sub-stage and displays Yes No
the elapsed time since this sub-stage started
Final verdict:
ETSI
22 ETSI TS 101 570-2 V1.2.1 (2020-02)
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0004
Summary: 'Validation that the required items of the automated procedure are being properly displayed'
Configuration: CF_VHF_1
References:
ETSI EN 300 338-2 [1], clauses 6.4.2 and 6.4.3
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT push the Distress Button
2 Release the distress button after the countdown is complete
3 Verify that the EUT indicates that it is in transmitting state during Yes No
distress alert transmission
4 Verify that the remaining time to the next automated sending of the Yes No
distress alert attempt is displayed on the EUT screen
5 Verify that the EUT sets the time to the next automated alert Yes No
sending to between 3,5 minutes and 4,5 minutes, and check that
this interval is different each time
6 Verify that the EUT still indicates that it is waiting for an Yes No
acknowledgement
7 Verify that the option to pause the countdown to the next distress Yes No
alert attempt is available on the EUT
8 Verify that the option to cancel the distress alert attempt is Yes No
available on the EUT
9 Verify that the option to resend the distress alert attempt is Yes No
available on the EUT
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0005
Summary: 'Validation that a paused automated procedure can be resumed'
Configuration: CF_VHF_1
References: ETSI EN 300 338-2 [1], clauses 6.4.2 and 6.4.3
Pre-test conditions:
Step Test Sequence Verdict
Pass Fail
1 On EUT push the Distress Button
2 Release the distress button after the countdown is complete
3 Wait until the EUT is in a countdown to the next distress alert
attempt and pause the countdown
4 Verify that the option to resume the countdown to the next distress Yes No
alert attempt is available on the EUT
Final verdict:
Interoperability Test Description
Identifier: TD_DSC_VHF_SDA_0006
Summary: 'Validation of the alert cancel procedure - warning'
Configuration:
CF_VHF_1
Re
...