ETSI EN 301 489-17 V3.1.1 (2017-02)

Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)

HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU

2 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)

Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2016.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.2 Arrangements for test signals . 8
4.2.0 General . 8
4.2.1 Arrangements for test signals at the input of transmitters . 8
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 9
4.2.4 Arrangements for test signals at the output of receivers . 9
4.2.5 Arrangements for testing transmitter and receiver together (as a system) . 9
4.2.6 Equipment with an external antenna connector . 9
4.2.7 Equipment without an external antenna connector (integral antenna) . 9
4.2.8 Equipment with more than one antenna . 10
4.3 Exclusion bands . 10
4.4 Narrow band responses on receivers or receivers which are part of transceivers . 10
4.5 Normal test modulation . 10
5 Performance assessment . 11
5.1 General . 11
5.2 Arrangements for the assessment of host dependant equipment and plug-in cards . 11
5.2.0 Introduction. 11
5.2.1 Alternative A: composite equipment . 11
5.2.2 Alternative B: use of a test jig or host . 11
5.3 Assessment procedures . 12
5.4 Ancillary equipment . 12
5.5 Equipment classification . 12
6 Performance criteria . 12
6.1 General performance criteria . 12
6.2 Performance table . 13
6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) . 13
6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) . 14
6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) . 14
6.6 Performance criteria for Transient phenomena applied to Receivers (TR) . 14
7 Applicability overview . 14
7.1 Emission . 14
7.1.1 General . 14
7.1.2 Special conditions . 14
7.2 Immunity . 14
7.2.1 General . 14
7.2.2 Special conditions . 15
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 16
Annex B (informative): Examples of radio equipment in the scope of the present document . 18
ETSI
4 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
B.1 Introduction . 18
B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation
techniques . 18
B.3 5 GHz high performance RLAN systems . 18
B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz . 18
B.5 Broadband data transmitting/BWA Terminal Stations . 18
B.6 Multi-Gigabit Wireless Systems (MGWS) . 18
Annex C (informative): Summary of changes from previous version . 19
History . 20

ETSI
5 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This final draft Harmonised European Standard (EN) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM), and is now submitted for the Vote phase of the
ETSI standards EN Approval Procedure.
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
6 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
1 Scope
The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of
measurements for Broadband Data Transmission System equipment, as detailed in annex B.
Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are
not included in the present document. Such technical specifications are found in the relevant product standards for the
effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
wideband data communication systems.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.1.1) (11-2016): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard
covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential
requirements of article 6 of Directive 2014/30/EU ".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
7 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance
RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE
Directive".
[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data
transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the
R&TTE Directive".
[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to
2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive".
[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in
the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the
Directive 2014/53/EU".
[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz
frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of
article 3.2 of the R&TTE Directive".
[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering
the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.
[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile
WiMAXTM) TDD User Equipment (UE)".
[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile
TM
WiMAX ) FDD User Equipment (UE)".
[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
Equipment Under Test (EUT): equipment subject to the performance requirements of the present document
fixed station: equipment intended for use in a fixed location and fitted with one or more antennas
NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.
hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person
NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna
socket(s) or integral antenna(s) or both.
host: any equipment which has complete user functionality when not connected to the radio equipment part and to
which the radio equipment part provides additional functionality and to which connection is necessary for the radio
equipment part to offer functionality
ETSI
8 Final draft ETSI EN 301 489-17 V3.1.1 (2016-11)
plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host
systems, using their control functions and power supply
stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally
used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General
For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as
appropriate. Further product related test conditions for wideband data communications systems are specified in
clauses 4.2 to 4.5.
The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires
connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases
the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.1 Arrangements for test signals at the input of transmitters
The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.
The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer.
The transmitter shall be operated at maximum rated power.
ETSI
----------------------
...

HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU

2 ETSI EN 301 489-17 V3.1.1 (2017-02)

Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 489-17 V3.1.1 (2017-02)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.2 Arrangements for test signals . 8
4.2.0 General . 8
4.2.1 Arrangements for test signals at the input of transmitters . 8
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 9
4.2.4 Arrangements for test signals at the output of receivers . 9
4.2.5 Arrangements for testing transmitter and receiver together (as a system) . 9
4.2.6 Equipment with an external antenna connector . 9
4.2.7 Equipment without an external antenna connector (integral antenna) . 9
4.2.8 Equipment with more than one antenna . 10
4.3 Exclusion bands . 10
4.4 Narrow band responses on receivers or receivers which are part of transceivers . 10
4.5 Normal test modulation . 10
5 Performance assessment . 11
5.1 General . 11
5.2 Arrangements for the assessment of host dependant equipment and plug-in cards . 11
5.2.0 Introduction. 11
5.2.1 Alternative A: composite equipment . 11
5.2.2 Alternative B: use of a test jig or host . 11
5.3 Assessment procedures . 12
5.4 Ancillary equipment . 12
5.5 Equipment classification . 12
6 Performance criteria . 12
6.1 General performance criteria . 12
6.2 Performance table . 13
6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) . 13
6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) . 14
6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) . 14
6.6 Performance criteria for Transient phenomena applied to Receivers (TR) . 14
7 Applicability overview . 14
7.1 Emission . 14
7.1.1 General . 14
7.1.2 Special conditions . 14
7.2 Immunity . 14
7.2.1 General . 14
7.2.2 Special conditions . 15
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 16
Annex B (informative): Examples of radio equipment in the scope of the present document . 18
ETSI
4 ETSI EN 301 489-17 V3.1.1 (2017-02)
B.1 Introduction . 18
B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation
techniques . 18
B.3 5 GHz high performance RLAN systems . 18
B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz . 18
B.5 Broadband data transmitting/BWA Terminal Stations . 18
B.6 Multi-Gigabit Wireless Systems (MGWS) . 18
Annex C (informative): Change History . 19
History . 20

ETSI
5 ETSI EN 301 489-17 V3.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 30 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
6 ETSI EN 301 489-17 V3.1.1 (2017-02)
1 Scope
The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of
measurements for Broadband Data Transmission System equipment, as detailed in annex B.
Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are
not included in the present document. Such technical specifications are found in the relevant product standards for the
effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
wideband data communication systems.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard
covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential
requirements of article 6 of Directive 2014/30/EU".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
7 ETSI EN 301 489-17 V3.1.1 (2017-02)
[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance
RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE
Directive".
[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data
transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the
R&TTE Directive".
[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to
2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive".
[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in
the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the
Directive 2014/53/EU".
[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz
frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of
article 3.2 of the R&TTE Directive".
[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering
the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.
[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile
WiMAXTM) TDD User Equipment (UE)".
[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile
TM
WiMAX ) FDD User Equipment (UE)".
[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
Equipment Under Test (EUT): equipment subject to the performance requirements of the present document
fixed station: equipment intended for use in a fixed location and fitted with one or more antennas
NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.
hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person
NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna
socket(s) or integral antenna(s) or both.
host: any equipment which has complete user functionality when not connected to the radio equipment part and to
which the radio equipment part provides additional functionality and to which connection is necessary for the radio
equipment part to offer functionality
ETSI
8 ETSI EN 301 489-17 V3.1.1 (2017-02)
plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host
systems, using their control functions and power supply
stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally
used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General
For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as
appropriate. Further product related test conditions for wideband data communications systems are specified in
clauses 4.2 to 4.5.
The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires
connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases
the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0 General
The provisions of ETSI EN 301 489-1 [1], clause 4.2 shall apply.
4.2.1 Arrangements for test signals at the input of transmitters
The provisions of ETSI EN 301 489-1 [1], clause 4.2.1 shall apply with the following modifications.
The wanted signals and/or controls required to establish a communications link shall be defined by the manufacturer.
The transmitter shall be operated at maximum rated power.
ETSI
...

SLOVENSKI STANDARD
01-april-2017
6WDQGDUGHOHNWURPDJQHWQH]GUXåOMLYRVWL(0&]DUDGLMVNRRSUHPRLQVWRULWYH
GHO3RVHEQLSRJRML]DãLURNRSDVRYQHVLVWHPH]DSUHQRVSRGDWNRY+DUPRQL]LUDQL
VWDQGDUGNL]DMHPDELVWYHQH]DKWHYHþOHQDEGLUHNWLYH(8
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services - Part
17: Specific conditions for Broadband Data Transmission Systems - Harmonised
Standard covering the essential requirements of article 3.1(b) of the Directive
2014/53/EU
Ta slovenski standard je istoveten z: ETSI EN 301 489-17 V3.1.1 (2017-02)
ICS:
33.060.01 Radijske komunikacije na Radiocommunications in
splošno general
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

HARMONISED EUROPEAN STANDARD
ElectroMagnetic Compatibility (EMC)
standard for radio equipment and services;
Part 17: Specific conditions for
Broadband Data Transmission Systems;
Harmonised Standard covering the essential requirements
of article 3.1(b) of Directive 2014/53/EU

2 ETSI EN 301 489-17 V3.1.1 (2017-02)

Reference
REN/ERM-EMC-335
Keywords
EMC, harmonised standard, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2017.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI EN 301 489-17 V3.1.1 (2017-02)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 6
3 Definitions and abbreviations . 7
3.1 Definitions . 7
3.2 Abbreviations . 8
4 Test conditions . 8
4.1 General . 8
4.2 Arrangements for test signals . 8
4.2.0 General . 8
4.2.1 Arrangements for test signals at the input of transmitters . 8
4.2.2 Arrangements for test signals at the output of transmitters . 9
4.2.3 Arrangements for test signals at the input of receivers . 9
4.2.4 Arrangements for test signals at the output of receivers . 9
4.2.5 Arrangements for testing transmitter and receiver together (as a system) . 9
4.2.6 Equipment with an external antenna connector . 9
4.2.7 Equipment without an external antenna connector (integral antenna) . 9
4.2.8 Equipment with more than one antenna . 10
4.3 Exclusion bands . 10
4.4 Narrow band responses on receivers or receivers which are part of transceivers . 10
4.5 Normal test modulation . 10
5 Performance assessment . 11
5.1 General . 11
5.2 Arrangements for the assessment of host dependant equipment and plug-in cards . 11
5.2.0 Introduction. 11
5.2.1 Alternative A: composite equipment . 11
5.2.2 Alternative B: use of a test jig or host . 11
5.3 Assessment procedures . 12
5.4 Ancillary equipment . 12
5.5 Equipment classification . 12
6 Performance criteria . 12
6.1 General performance criteria . 12
6.2 Performance table . 13
6.3 Performance criteria for Continuous phenomena applied to Transmitters (CT) . 13
6.4 Performance criteria for Transient phenomena applied to Transmitters (TT) . 14
6.5 Performance criteria for Continuous phenomena applied to Receivers (CR) . 14
6.6 Performance criteria for Transient phenomena applied to Receivers (TR) . 14
7 Applicability overview . 14
7.1 Emission . 14
7.1.1 General . 14
7.1.2 Special conditions . 14
7.2 Immunity . 14
7.2.1 General . 14
7.2.2 Special conditions . 15
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 16
Annex B (informative): Examples of radio equipment in the scope of the present document . 18
ETSI
4 ETSI EN 301 489-17 V3.1.1 (2017-02)
B.1 Introduction . 18
B.2 Data transmission systems operating in the 2,4 GHz ISM band and using wide band modulation
techniques . 18
B.3 5 GHz high performance RLAN systems . 18
B.4 Broadband data transmitting systems operating in the band 5 725 MHz to 5 875 MHz . 18
B.5 Broadband data transmitting/BWA Terminal Stations . 18
B.6 Multi-Gigabit Wireless Systems (MGWS) . 18
Annex C (informative): Change History . 19
History . 20

ETSI
5 ETSI EN 301 489-17 V3.1.1 (2017-02)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
The present document has been prepared under the Commission's standardisation request C(2015) 5376 final [i.12] to
provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation
of the laws of the Member States relating to the making available on the market of radio equipment and repealing
Directive 1999/5/EC [i.1].
Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with
the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present
document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated
EFTA regulations.
The present document is part 17 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].

National transposition dates
Date of adoption of this EN: 30 January 2017
Date of latest announcement of this EN (doa): 30 April 2017
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 October 2017
Date of withdrawal of any conflicting National Standard (dow): 31 October 2018

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
6 ETSI EN 301 489-17 V3.1.1 (2017-02)
1 Scope
The present document, together with ETSI EN 301 489-1 [1], specifies technical characteristics and methods of
measurements for Broadband Data Transmission System equipment, as detailed in annex B.
Technical specifications related to the antenna port and emissions from the enclosure port of the radio equipment are
not included in the present document. Such technical specifications are found in the relevant product standards for the
effective use of the radio spectrum.
The present document specifies the applicable test conditions, performance assessment and performance criteria for
wideband data communication systems.
In case of differences (for instance concerning special conditions, definitions, abbreviations) between the present
document and ETSI EN 301 489-1 [1], the provisions of the present document take precedence.
The environmental classification and the emission and immunity requirements used in the present document are as
stated in ETSI EN 301 489-1 [1], except for any special conditions included in the present document.
The present document covers the essential requirements of article 3.1(b) of Directive 2014/53/EU [i.1] under the
conditions identified in annex A.
2 References
2.1 Normative references
References are specific, identified by date of publication and/or edition number or version number. Only the cited
version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 301 489-1 (V2.1.1) (02-2017): "ElectroMagnetic Compatibility (EMC) standard for
radio equipment and services; Part 1: Common technical requirements; Harmonised Standard
covering the essential requirements of article 3.1(b) of Directive 2014/53/EU and the essential
requirements of article 6 of Directive 2014/30/EU".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 2014/53/EU of the European Parliament and of the council of 16 April 2014 on the
harmonisation of the laws of the Member States relating to the making available on the market of
radio equipment and repealing Directive 1999/5/EC.
[i.2] Void.
ETSI
7 ETSI EN 301 489-17 V3.1.1 (2017-02)
[i.3] ETSI EN 301 893: "Broadband Radio Access Networks (BRAN); 5 GHz high performance
RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE
Directive".
[i.4] ETSI EN 302 502: "Broadband Radio Access Networks (BRAN); 5,8 GHz fixed broadband data
transmitting systems; Harmonized EN covering the essential requirements of article 3.2 of the
R&TTE Directive".
[i.5] ETSI EN 302 544-2: "Broadband Data Transmission Systems operating in the 2 500 MHz to
2 690 MHz frequency band; Part 2: TDD User Equipment Stations; Harmonized EN covering the
essential requirements of article 3.2 of the R&TTE Directive".
[i.6] ETSI EN 302 567: "WAS/RLAN systems; Multiple-Gigabit WAS/RLAN equipment operating in
the 60 GHz band; Harmonised Standard covering the essential requirements of article 3.2 of the
Directive 2014/53/EU".
[i.7] ETSI EN 302 623: "Broadband Wireless Access Systems (BWA) in the 3 400 MHz to 3 800 MHz
frequency band; Mobile Terminal Stations; Harmonized EN covering the essential requirements of
article 3.2 of the R&TTE Directive".
[i.8] ETSI EN 300 328: "Wideband transmission systems; Data transmission equipment operating in the
2,4 GHz ISM band and using wide band modulation techniques; Harmonised Standard covering
the essential requirements of article 3.2 of Directive 2014/53/EU".
[i.9] Void.
[i.10] ETSI EN 301 908-19: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 19: OFDMA TDD WMAN (Mobile
WiMAXTM) TDD User Equipment (UE)".
[i.11] ETSI EN 301 908-21: "IMT cellular networks; Harmonised Standard covering the essential
requirements of article 3.2 of the Directive 2014/53/EU; Part 21: OFDMA TDD WMAN (Mobile
TM
WiMAX ) FDD User Equipment (UE)".
[i.12] Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request
to the European Committee for Electrotechnical Standardisation and to the European
Telecommunications Standards Institute as regards radio equipment in support of Directive
2014/53/EU of the European Parliament and of the Council.
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in ETSI EN 301 489-1 [1] and the following
apply:
Equipment Under Test (EUT): equipment subject to the performance requirements of the present document
fixed station: equipment intended for use in a fixed location and fitted with one or more antennas
NOTE: The equipment may be fitted with either antenna socket(s) or integral antenna(s) or both.
hand-portable station: equipment normally used on a stand-alone basis and to be carried by a person
NOTE: The equipment may be fitted with one or more antennas. The equipment may be fitted with either antenna
socket(s) or integral antenna(s) or both.
host: any equipment which has complete user functionality when not connected to the radio equipment part and to
which the radio equipment part provides additional functionality and to which connection is necessary for the radio
equipment part to offer functionality
ETSI
8 ETSI EN 301 489-17 V3.1.1 (2017-02)
plug-in radio device: equipment, including slide-in radio cards, intended to be used with or within a variety of host
systems, using their control functions and power supply
stand-alone radio equipment: equipment that is intended primarily as communications equipment and that is normally
used on a stand-alone basis
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AC Alternating Current
ACK ACKnowledgement
ARQ Automatic Retransmission reQuest
BRAN Broadband Radio Access Networks
BWA Broadband Wireless Access
CR Continuous phenomena applied to Receivers
CT Continuous phenomena applied to Transmitters
DC Direct Current
EMC ElectroMagnetic Compatibility
ERM Electromagnetic compatibility and Radio Matters
EUT Equipment Under Test
ISM Industrial, Scientific and Medical
MGWS Multi-Gigabit Wireless Systems
MUS Maximum Usable Sensitivity
NACK Not ACKnowledgement
RF Radio Frequency
RLAN Radio Local Area Network
TR Transient phenomena applied to Receivers
TT Transient phenomena applied to Transmitters
4 Test conditions
4.1 General
For the purposes of the present document, the test conditions of ETSI EN 301 489-1 [1], clause 4, shall apply as
appropriate. Further product related test conditions for wideband data communications systems are specified in
clauses 4.2 to 4.5.
The radio equipment may take forms which may require special software and/or test fixtures. Equipment which requires
connection to a host equipment to function shall use the test configuration as defined by the manufacturer. In all cases
the EUT shall be exercised in a manner representative of normal intended use.
4.2 Arrangements for test signals
4.2.0
...