ETSI EN 303 203-2 V1.1.1 (2014-11)

ETSI EN 303 203-2 V1.1.1 (2014-11)






HARMONIZED EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Medical Body Area Network Systems (MBANSs)
operating in the 2 483,5 MHz to 2 500 MHz range;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 303 203-2 V1.1.1 (2014-11)



Reference
DEN/ERM-TG30-305
Keywords
health, network, radio, regulation, SRD, system
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 303 203-2 V1.1.1 (2014-11)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements and specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency Error . 8
4.2.1.1.1 Definition. 8
4.2.1.1.2 Limits . 9
4.2.1.1.3 Conformance . 9
4.2.1.2 Emission bandwidth . 9
4.2.1.2.1 Definition. 9
4.2.1.2.2 Limits . 9
4.2.1.2.3 Conformance . 9
4.2.1.3 Effective isotropic radiated power . 9
4.2.1.3.1 Definition. 9
4.2.1.3.2 Limits . 9
4.2.1.3.3 Conformance . 9
4.2.1.4 Spurious emissions . 9
4.2.1.4.1 Definition. 9
4.2.1.4.2 Limits . 9
4.2.1.4.3 Conformance . 9
4.2.1.5 Out-of-band emissions . 9
4.2.1.5.1 Definition. 9
4.2.1.5.2 Limits . 10
4.2.1.5.3 Conformance . 10
4.2.1.6 Frequency stability under low voltage conditions . 10
4.2.1.6.1 Definition. 10
4.2.1.6.2 Limits . 10
4.2.1.6.3 Conformance . 10
4.2.1.7 Duty cycle . 10
4.2.1.7.1 Definition. 10
4.2.1.7.2 Limits . 10
4.2.1.7.3 Conformance . 10
4.2.2 Receiver requirements . 10
4.2.2.1 Spurious radiation . 10
4.2.2.1.1 Definition. 10
4.2.2.1.2 Limits . 10
4.2.2.1.3 Conformance . 10
4.2.3 Spectrum access . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 303 203-2 V1.1.1 (2014-11)
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Presentation for testing . 11
5.1.2 Test conditions . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Emission bandwidth . 12
5.3.3 Effective isotropic radiated power . 12
5.3.4 Transmitter spurious emis sions . 12
5.3.5 Out-of-band emissions . 12
5.3.6 Frequency stability under low voltage conditions . 12
5.3.7 Receiver spurious emissions . 12
5.3.8 Spectrum access . 12
5.3.9 Normal test-conditions . 12
5.3.10 Extreme test-conditions . 12
5.3.11 Test power source . 12
5.3.12 Choice of samples for test suites . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): Change History . 15
Annex C (informative): Bibliography . 16
History . 17

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 303 203-2 V1.1.1 (2014-11)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM).
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.7] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3].
See article 5.1 of Directive 1999/5/EC [i.3] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering Medical Body Area Network Systems (MBANSs)
operating in the 2 483,5 MHz to 2 500 MHz range, as described in the systems reference document for the equipment,
TR 101 557 [i.1], and as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".

National transposition dates
Date of adoption of this EN: 30 October 2014
Date of latest announcement of this EN (doa): 31 January 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2015
Date of withdrawal of any conflicting National Standard (dow): 31 July 2016

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 303 203-2 V1.1.1 (2014-11)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.
...

Draft ETSI EN 303 203-2 V1.1.0 (2014-07)






HARMONIZED EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Short Range Devices (SRD);
Medical Body Area Network Systems (MBANSs) operating in
the 2 483,5 MHz to 2 500 MHz range;
Part 2: Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 303 203-2 V1.1.0 (2014-07)



Reference
DEN/ERM-TG30-305
Keywords
health, network, radio, regulation, SRD, system
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 303 203-2 V1.1.0 (2014-07)
Contents
Intellectual Property Rights . 5
Foreword . 5
Modal verbs terminology . 5
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definitions, symbols and abbreviations . 8
3.1 Definitions . 8
3.2 Symbols . 8
3.3 Abbreviations . 8
4 Technical requirements and specifications . 8
4.1 Environmental profile . 8
4.2 Conformance requirements . 8
4.2.1 Transmitter requirements . 8
4.2.1.1 Frequency Error . 8
4.2.1.1.1 Definition. 8
4.2.1.1.2 Limits . 9
4.2.1.1.3 Conformance . 9
4.2.1.2 Emission bandwidth . 9
4.2.1.2.1 Definition. 9
4.2.1.2.2 Limits . 9
4.2.1.2.3 Conformance . 9
4.2.1.3 Effective isotropic radiated power . 9
4.2.1.3.1 Definition. 9
4.2.1.3.2 Limits . 9
4.2.1.3.3 Conformance . 9
4.2.1.4 Spurious emissions . 9
4.2.1.4.1 Definition. 9
4.2.1.4.2 Limits . 9
4.2.1.4.3 Conformance . 9
4.2.1.5 Out-of-band emissions . 9
4.2.1.5.1 Definition. 9
4.2.1.5.2 Limits . 10
4.2.1.5.3 Conformance . 10
4.2.1.6 Frequency stability under low voltage conditions . 10
4.2.1.6.1 Definition. 10
4.2.1.6.2 Limits . 10
4.2.1.6.3 Conformance . 10
4.2.1.7 Duty cycle . 10
4.2.1.7.1 Definition. 10
4.2.1.7.2 Limits . 10
4.2.1.7.3 Conformance . 10
4.2.2 Receiver requirements . 10
4.2.2.1 Spurious radiation . 10
4.2.2.1.1 Definition. 10
4.2.2.1.2 Limits . 10
4.2.2.1.3 Conformance . 10
4.2.3 Spectrum access . 11
4.2.3.1 Definition . 11
4.2.3.2 Limits . 11
4.2.3.3 Conformance . 11
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 303 203-2 V1.1.0 (2014-07)
5 Testing for compliance with technical requirements . 11
5.1 Environmental conditions for testing . 11
5.1.1 Presentation for testing . 11
5.1.2 Test conditions . 11
5.2 Interpretation of the measurement results . 11
5.3 Essential radio test suites . 12
5.3.1 Frequency error . 12
5.3.2 Emission bandwidth . 12
5.3.3 Effective isotropic radiated power . 12
5.3.4 Transmitter spurious emis sions . 12
5.3.5 Out-of-band emissions . 12
5.3.6 Frequency stability under low voltage conditions . 12
5.3.7 Receiver spurious emissions . 12
5.3.8 Spectrum access . 12
5.3.9 Normal test-conditions . 12
5.3.10 Extreme test-conditions . 12
5.3.11 Test power source . 12
5.3.12 Choice of samples for test suites . 12
Annex A (normative): HS Requirements and conformance Test specifications Table
(HS-RTT) . 13
Annex B (informative): Change History . 15
Annex C (informative): Bibliography . 16
History . 17

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 303 203-2 V1.1.0 (2014-07)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic
compatibility and Radio spectrum Matters (ERM), and is now submitted for the combined Public Enquiry and Vote
phase of the ETSI standards EN Approval Procedure.
For non EU countries the present document may be used for regulatory (Type Approval) purposes.
The present document has been produced by ETSI in response to mandate M/284 issued from the European
Commission under Directive 98/34/EC [i.7] as amended by Directive 98/48/EC [i.6].
The title and reference to the present document are intended to be included in the publication in the Official Journal of
the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.3].
See article 5.1 of Directive 1999/5/EC [i.3] for information on presumption of conformity and Harmonized Standards or
parts thereof the references of which have been published in the Official Journal of the European Union.
The requirements relevant to Directive 1999/5/EC [i.3] are summarized in annex A.
The present document is part 2 of a multi-part deliverable covering Medical Body Area Network Systems (MBANSs)
operating in the 2 483,5 MHz to 2 500 MHz range, as described in the systems reference document for the equipment,
TR 101 557 [i.1], and as identified below:
Part 1: "Technical characteristics and test methods";
Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 18 months after doa

Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 303 203-2 V1.1.0 (2014-07)
Introduction
The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to
cover all radio and telecommunications termi
...