ETSI EN 301 908-18 V6.2.1 (2012-11)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.*60('*(IMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 18: E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Station (BS)33.070.99Druge mobilne storitveOther mobile services33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-18 Version 6.2.1SIST EN 301 908-18 V6.2.1:2013en01-februar-2013SIST EN 301 908-18 V6.2.1:2013SLOVENSKI
STANDARD



SIST EN 301 908-18 V6.2.1:2013



ETSI EN 301 908-18 V6.2.1 (2012-11) IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 18: E-UTRA, UTRA and GSM/EDGE
Multi-Standard Radio (MSR) Base Station (BS)
Harmonized European Standard SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)2
Reference REN/MSG-TFES-010-18 Keywords 3G, 3GPP, cellular, digital, EDGE, E-UTRA, GSM, IMT-2000, LTE, mobile, MSR, radio, regulation, UMTS, UTRA, WCDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2012. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 6 1 Scope . 7 2 References . 7 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 11 3.3 Abbreviations . 11 4 Technical requirements specifications . 12 4.1 Environmental profile . 12 4.2 Conformance requirements . 12 4.2.1 Introduction. 13 4.2.2 Operating band unwanted emissions . 14 4.2.2.1 Definition . 14 4.2.2.2 Limits . 14 4.2.2.2.1 Limits for Band Categories 1 and 3 . 14 4.2.2.2.2 Limits for Band Category 2 . 15 4.2.2.2.3 Limits for GSM/EDGE single-RAT operation . 16 4.2.2.2.4 Limits for protection of DTT . 16 4.2.2.2.5 Limits for co-existence with services in adjacent frequency bands . 17 4.2.2.3 Conformance . 17 4.2.3 Adjacent Channel Leakage power Ratio (ACLR) . 17 4.2.3.1 Definition . 17 4.2.3.2 Limits . 17 4.2.3.2.1 E-UTRA limits . 17 4.2.3.2.2 UTRA FDD limits . 18 4.2.3.2.3 UTRA TDD limits . 18 4.2.3.2.4 Cumulative ACLR requirement in non-contiguous spectrum . 18 4.2.3.3 Conformance . 19 4.2.4 Transmitter spurious emissions . 19 4.2.4.1 Limits . 19 4.2.4.1.1 Spurious emissions . 19 4.2.4.1.2 Additional spurious emissions requirement for BC2 . 19 4.2.4.1.3 Co-existence with other systems . 19 4.2.4.1.4 Protection of the BS receiver of own or different BS . 21 4.2.4.2 Conformance . 21 4.2.5 Base station maximum output power . 21 4.2.5.1 Definition . 21 4.2.5.2 Limits . 21 4.2.5.3 Conformance . 22 4.2.6 Transmit intermodulation . 22 4.2.6.1 Definition . 22 4.2.6.2 Limits . 22 4.2.6.2.1 General limits . 22 4.2.6.2.2 Additional limits (BC1 and BC2) . 22 4.2.6.2.3 Additional limits (BC3) . 23 4.2.6.3 Conformance . 23 4.2.7 Receiver spurious emissions . 23 4.2.7.1 Definition . 23 4.2.7.2 Limits . 24 SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)4 4.2.7.2.1 General limits . 24 4.2.7.2.2 Additional limits for BC2 . 24 4.2.7.3 Conformance . 24 4.2.8 In-band blocking . 24 4.2.8.1 Definition . 24 4.2.8.2 Limits . 24 4.2.8.2.1 General limits . 24 4.2.8.2.2 Additional BC3 blocking limits . 25 4.2.8.3 Conformance . 26 4.2.9 Out-of-band blocking . 26 4.2.9.1 Definition . 26 4.2.9.2 Limits . 26 4.2.9.3 Conformance . 26 4.2.10 Receiver intermodulation characteristics . 27 4.2.10.1 Definition . 27 4.2.10.2 Limits . 27 4.2.10.2.1 General intermodulation limits . 27 4.2.10.2.2 General narrowband intermodulation limits . 28 4.2.10.2.3 Additional narrowband intermodulation limits for GSM/EDGE . 29 4.2.10.3 Conformance . 29 4.2.11 Narrowband blocking . 29 4.2.11.1 Definition . 29 4.2.11.2 Limits . 30 4.2.11.2.1 General limits . 30 4.2.11.2.2 Additional limits for GSM/EDGE . 30 4.2.11.2.3 GSM/EDGE limits for AM suppression . 30 4.2.11.3 Conformance . 30 5 Testing for compliance with technical requirements . 31 5.1 Environmental conditions for testing . 31 5.2 Interpretation of the measurement results . 31 5.3 Essential radio test suites . 32 5.3.1 Operating band unwanted emissions . 32 5.3.1.1 Initial conditions . 33 5.3.1.2 Procedure . 33 5.3.1.3 Test requirement . 33 5.3.2 Adjacent Channel Leakage power Ratio (ACLR) . 33 5.3.2.1 Initial conditions . 34 5.3.2.2 Procedure . 34 5.3.2.3 Test requirement . 34 5.3.3 Transmitter spurious emissions . 34 5.3.3.1 Initial conditions . 34 5.3.3.2 Procedure . 34 5.3.3.3 Test requirement . 34 5.3.4 Base station maximum output power . 35 5.3.4.1 Initial conditions . 35 5.3.4.2 Procedure . 35 5.3.4.3 Test requirement . 35 5.3.5 Transmit intermodulation . 35 5.3.5.1 Initial conditions . 35 5.3.5.2 Procedure . 35 5.3.5.2.1 General minimum requirement test procedure . 35 5.3.5.2.2 Additional minimum requirement (BC1 and BC2) test procedure . 36 5.3.5.2.3 Additional minimum requirement (BC3) test procedure . 37 5.3.5.3 Test requirement . 37 5.3.6 Receiver spurious emissions . 38 5.3.6.1 Initial conditions . 38 5.3.6.2 Procedure . 38 5.3.6.3 Test requirement . 38 5.3.7 In-band blocking . 38 5.3.7.1 Initial conditions . 38 5.3.7.2 Procedure . 38 SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)5 5.3.7.2.1 Procedure for general blocking . 38 5.3.7.2.2 Procedure for additional BC3 blocking requirement . 39 5.3.7.3 Test requirement . 39 5.3.8 Out-of-band blocking . 39 5.3.8.1 Initial conditions . 39 5.3.8.2 Procedure . 39 5.3.8.3 Test requirement . 39 5.3.9 Receiver intermodulation characteristics . 39 5.3.9.1 Initial conditions . 39 5.3.9.2 Procedure . 40 5.3.9.2.1 Procedure for general and narrowband intermodulation . 40 5.3.9.2.2 Procedure for additional narrowband intermodulation for GSM/EDGE . 40 5.3.9.3 Test requirement . 40 5.3.10 Narrowband blocking . 40 5.3.10.1 Initial conditions . 40 5.3.10.2 Procedure . 40 5.3.10.2.1 Procedure for narrowband blocking . 40 5.3.10.2.2 Procedure for additional narrowband blocking for GSM/EDGE . 41 5.3.10.2.3 Procedure for GSM/EDGE AM suppression . 41 5.3.10.3 Test requirement . 41 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 42 Annex B (normative): Base Station configurations . 44 B.1 Reception with multiple receiver antenna connectors and receiver diversity . 44 B.2 Duplexers . 44 B.3 Power supply options . 44 B.4 Ancillary RF amplifiers . 44 B.5 BS using antenna arrays . 45 B.5.1 Receiver tests . 45 B.5.2 Transmitter tests . 46 B.6 Transmission with multiple transmitter antenna connectors . 46 B.7 BS with integrated Iuant BS modem . 46 Annex C (informative): Environmental profile specification . 47 Annex D (informative): Void . 48 Annex E (informative): Bibliography . 49 History . 50
SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Directive 98/34/EC [i.1] as amended by Directive 98/48/EC [i.6]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A. The present document is part 18 of a multi-part deliverable. Full details of the entire series can be found in part 1 [1].
National transposition dates Date of adoption of this EN: 16 November 2012 Date of latest announcement of this EN (doa): 28 February 2013 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 August 2013 Date of withdrawal of any conflicting National Standard (dow): 31 August 2014
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-18 V6.2.1:2013



ETSI ETSI EN 301 908-18 V6.2.1 (2012-11)7 1 Scope The present document applies to the following radio equipment type: 1) Multi-Standard Radio capable Base stations (E-UTRA, UTRA, GSM/EDGE). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: Base station operating bands Band designation and Band Category Direction of transmission MSR Base Station operating bands 1 (BC1) Transmit
2 110 MHz to 2 170 MHz Receive
1 920 MHz to 1 980 MHz 3 (BC2) Transmit
1 805 MHz to 1 880 MHz
Receive
1 710 MHz to 1 785 MHz
7 (BC1) Transmit
2 620 MHz to 2 690 MHz
Receive
2 500 MHz to 2 570 MHz
8 (BC2) Transmit
925 MHz to 960 MHz
Receive
880 MHz to 915 MHz
20 (BC1) Transmit
791 MHz to 821 MHz Receive
832 MHz to 862 MHz 22 (BC1) Transmit
3 510 MHz to 3 590 MHz Receive
3 410 MHz to 3 490 MHz 33 (BC3)
Transmit and Receive 1 900 MHz to 1 920 MHz 34 (BC3) Transmit and Receive 2 010 MHz to 2 025 MHz 38 (BC3) Transmit and Receive 2 570 MHz to 2 620 MHz 40 (BC3) Transmit and Receive 2 300 MHz to 2 400 MHz 42 (BC3) Transmit and Receive 3 400 MHz to 3 600 MHz 43 (BC3) Transmit and Receive 3 600 MHz to 3 800 MHz
The present document covers requirements for multi-RAT capable E-
...