ETSI TS 103 239-1 V1.1.1 (2015-01)

ETSI TS 103 239-1 V1.1.1 (2015-01)






TECHNICAL SPECIFICATION
Integrated broadband cable
telecommunication networks (CABLE);
Testing; Conformance test specifications
for MAP-E technology;
Part 1: Protocol Implementation
Conformance Statement (PICS) proforma

---------------------- Page: 1 ----------------------
2 ETSI TS 103 239-1 V1.1.1 (2015-01)



Reference
DTS/CABLE-00012-1
Keywords
CABLE, IPCable, IPv6
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 103 239-1 V1.1.1 (2015-01)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions and abbreviations . 5
3.1 Definitions . 5
3.2 Abbreviations . 6
4 Conformance requirement concerning PICS . 6
Annex A (normative): MAP-E PICS Proforma . 7
A.1 Guidance for completing the PICS proforma . 7
A.1.1 Purposes and structure . 7
A.1.2 Abbreviations and conventions . 7
A.1.3 Instructions for completing the PICS proforma. 9
A.2 Identification of the implementation . 9
A.2.1 Date of the statement . 9
A.2.2 Implementation Under Test (IUT) identification . 9
A.2.3 System Under Test (SUT) identification . 9
A.2.4 Product supplier . 10
A.2.5 Client (if different from product supplier) . 10
A.2.6 PICS contact person . 11
A.3 Identification of the protocol . 11
A.4 Global statement of conformance . 11
A.5 Tables . 11
A.5.1 Transition Hardware . 11
A.5.2 Initialization procedures . 12
A.5.3 Fragmentation & MTU procedures . 12
A.5.4 Forwarding procedures . 12
A.5.5 Transition procedures . 12
Annex B (informative): Bibliography . 13
History . 14

ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 103 239-1 V1.1.1 (2015-01)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Integrated broadband cable
telecommunication networks (CABLE).
The present document produced for the transition technologies accommodates an urgent need in the industry to define
requirements that enable seamless transition of Cable Networks to IPv6. Considering the depletion of IPv4 addresses,
transition to IPv6 is required in order to enable continued growth of the customer base connected to Cable Networks
and ensure service continuity for existing and new customers. High-quality connectivity to all kinds of IP-based
services and networks is essential in today's business and private life.
A plethora of transition technologies have been proposed in IETF, other standardization organizations and by
manufacturers of IP technology to allow coexistence of IPv4 and IPv6 hosts, access and core networks as well as
services. Each of these technology options is specified, implemented and deployed in various forms and stages. The
present document is based on the requirements of ETSI TS 101 569-1 [1].
The present document is part 1 of a multi-part deliverable covering the conformance test specification for MAP-E
technology, as identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS) proforma";
Part 2: "Test Suite Structure and Test Purposes (TSS&TP)";
Part 3: "Abstract Test Suite (ATS) and Protocol Implementation eXtra Information for Testing (PIXIT)".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 103 239-1 V1.1.1 (2015-01)
1 Scope
The present document provides the Protocol Implementation Conformance Statement (PICS) proforma for conformance
test specifications for the IPv6 transition technology 6rd as defined in ETSI TS 101 569-1 [1] in compliance with the
relevant requirements and in accordance with the relevant guidance given in ISO/IEC 9646-7 [3].
A supplier of an implementation which is claimed to conform to ETSI TS 101 569-1 [1] is required to complete a copy
of the PICS proforma provided in the annex A of present document.
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 101 569-1 (V1.1.1) (2013-10): "Integrated Broadband Cable Telecommunication
Networks (CABLE); Cable Network Transition to IPv6 Part 1: IPv6 Transition Requirements".
[2] ISO/IEC 9646-1 (1994): "Information technology -- Open Systems Interconnection --
Conformance testing methodology and framework -- Part 1: General concepts".
[3] ISO/IEC 9646-7 (1994): "Information technology -- Open Systems Interconnection --
Conformance testing methodology and framework -- Part 7: Implementation Conformance
Statements".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
Not applicable.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 103 239-1 V1.1.1 (2015-01)
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions given in ETSI TS 101 569-1 [1],
ISO/IEC 9646-1 [2] and ISO/IEC 9646-7 [3] apply. In particular, the following terms given in ISO/IEC 9646-1 [2]
apply:
Implementation Conformance Statement (ICS): statement made by the supplier of an implementation or system
claimed to conform to a given specification, stating which capabilities have been implemented
ICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system
becomes an ICS
Protocol ICS (PICS): ICS for an implementation or system claimed to conform to a given protocol specification
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ATS Abstract Test Suite
B4 (MAP-E) Basic Bridging BroadBand element
BR Border Router
GW GateWay
ICS Implementation Conformance Statement
IP Internet Protocol
IPv4 IP version 4
IPv6 IP version 6
IUT Implementation Under Test
LAN Local Area Network
MAP-E Mapping of Address and Port - Encapsulation
MSS (TCP) Maximum Segment Size
MTU Maximum Transmission Unit
NAT Network Address Translation/Network Address Translator
PDU Protocol Data Unit
PICS Protocol Implementation Conformance Statement
SUT System Under Test
4 Conformance requirement concerning PICS
If it claims to conform to the present document, the actual PICS proforma to be filled in by a supplier shall be
technically equivalent to the text of the PICS proforma given in annex A and shall preserve the numbering/naming and
ordering of the proforma items.
A PICS which conforms to the present document shall be a conforming PICS proforma completed in accordance with
the instructions for completion given in clause A.1.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TS 103 239-1 V1.1.1 (2015-01)
Annex A (normative):
MAP-E PICS Proforma
Notwithstanding the provisions of the copyright clause related to the text of the present document, ETSI grants that
users of the present document may freely reproduce the MAP-E PICS proforma in this annex so that it can be used for
its intended purposes and may further publish the completed MAP-E PICS.
A.1 Guidance for completing the PICS proforma
A.1.1 Purposes and structure
The purpose of this PICS proforma is to provide a mechanism whereby a supplier of an implementation of the
requirements defined in ETSI TS 101 569-1 [1] may provide information about the implementation in a standardized
manner.
The PICS proforma is subdivided into clauses for the following categories of information:
- guidance for completing the PICS proforma;
- identification of the implementation;
- identification of the ETSI TS 101 569-1 [1];
- global statement of conformance;
- PICS proforma tables.
A.1.2 Abbreviations and conventions
The PICS proforma contained in this annex is comprised of information in tabular form in accordance with the
guidelines presented in ISO/IEC 9646-7 [3].
Item column
The item column contains a number which identifies the item in the table.
...