ETSI TS 103 161-10 V1.1.1 (2011-10)
Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5; Part 10: Management Information Base (MIB) Framework
Access, Terminals, Transmission and Multiplexing (ATTM); Integrated Broadband Cable and Television Networks; IPCablecom 1.5; Part 10: Management Information Base (MIB) Framework
DTS/ATTM-003011-10
General Information
Standards Content (Sample)
Technical Specification
Access, Terminals, Transmission and Multiplexing (ATTM);
Integrated Broadband Cable and Television Networks;
IPCablecom 1.5;
Part 10: Management Information Base (MIB) Framework
2 ETSI TS 103 161-10 V1.1.1 (2011-10)
Reference
DTS/ATTM-003011-10
Keywords
access, broadband, cable, IP, multimedia, PSTN
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners. ®
GSM and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI
3 ETSI TS 103 161-10 V1.1.1 (2011-10)
Contents
Intellectual Property Rights . 5
Foreword . 5
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 8
3 Definitions and abbreviations . 9
3.1 Definitions . 9
3.2 Abbreviations . 9
4 Void . 10
5 Overview . . 10
5.1 IPCablecom Reference Architecture . 10
5.2 General Requirements . 11
5.2.1 Provisioning and Network Management Service Provider . 11
5.2.2 Support for Embedded MTAs . 11
5.2.3 SNMP Considerations. 12
5.2.3.1 USM Requirements . 12
5.2.3.2 VACM Requirements. 13
5.2.3.2.1 VacmSecurityToGroup Table . 13
5.2.3.2.2 vacmAccessTable . 13
5.2.3.2.3 MIB View Requirements . 13
5.3 Functional Requirements . 14
5.3.1 IPCablecom Device Provisioning . 14
5.3.2 Security . 14
5.3.3 Voice interfaces . 14
5.3.4 IPCablecom Voice Call Signalling . 14
5.3.5 Media Packet Transport . 14
5.3.6 Fault Management . 15
5.3.7 Performance Management . 15
5.3.8 Event Management . 15
6 MIB modules Available in an IPCablecom Network . 15 ®
6.1 DOCSIS MIB Modules . 15
6.2 IF MIB . 16
6.3 MIB II . 16
6.3.1 sysDescr Requirements . 16
6.3.2 sysObjectID Requirements . 16
6.3.3 "iftable" Requirements . 16
6.4 IPCablecom SIGNALLING MIB . 18
6.4.1 MTA SIGNALLING MIB general configuration information . 18
6.4.2 MTA NCS MIB per endpoint data . 18
6.5 IPCablecom MTA MIB module . 18
6.6 Event Management MIB . 18
6.7 SNMP MIB . 18
6.8 IPCablecom Extension MIB . 18
6.8.1 MTA MIB Extension: . 19
6.8.2 Signalling MIB Extension . 19 ®
6.9 eDOCSIS eSAFE MIB . 19
6.10 Battery Backup UPS MIB . 19
7 IPCablecom MIB module Implementation . 19
7.1 MTA components . 19
7.2 MIB Layering . 20
ETSI
4 ETSI TS 103 161-10 V1.1.1 (2011-10)
Annex A (informative): Bibliography . 21
History . 22
ETSI
5 ETSI TS 103 161-10 V1.1.1 (2011-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Access, Terminals, Transmission
and Multiplexing (ATTM).
The present document is part 10 of a multi-part IPCablecom 1.5 deliverable covering the Digital Broadband Cable
Access to the Public Telecommunications Network; IP Multimedia Time Critical Services, as identified below:
Part 1: "Overview";
Part 2: "Architectural framework for the delivery of time critical services over Cable Television Networks using
Cable Modems";
Part 3: "Audio Codec Requirements for the Provision of Bi-Directional Audio Service over Cable Television
Networks using Cable Modems";
Part 4: "Network Call Signalling Protocol";
Part 5: "Dynamic Quality of Service for the Provision of Real Time Services over Cable Television Networks
using Cable Modems";
Part 6: "Event Message Specification";
Part 7: "Media Terminal Adapter (MTA Management Information Base (MIB)";
Part 8: "Network Call Signalling (NCS) MIB Requirements";
Part 9: "Security";
Part 10: "Management Information Base (MIB) Framework";
Part 11: "Media terminal adapter (MTA) device provisioning";
Part 12: "Management Event Mechanism";
Part 13: "Trunking Gateway Control Protocol - MGCP option";
Part 14: "Embedded MTA Analog Interface and Powering Specification"
Part 15: "Analog Trunking for PBX Specification";
Part 16: "Signalling for Call Management Server";
Part 17: "CMS Subscriber Provisioning Specification";
Part 18: "Media Terminal Adapter Extension MIB";
Part 19: "IPCablecom Audio Server Protocol Specification - MGCP option";
Part 20: "Management Event MIB Specification";
ETSI
6 ETSI TS 103 161-10 V1.1.1 (2011-10)
Part 21: "Signalling Extension MIB Specification".
NOTE 1: Additional parts may be proposed and will be added to the list in future versions.
NOTE 2: The choice of a multi-part format for this deliverable is to facilitate maintenance and future
enhancements.
ETSI
7 ETSI TS 103 161-10 V1.1.1 (2011-10)
1 Scope
The present document describes the framework in which IPCablecom1.5 MIB (Management Information Base)
modules are described. It provides information on the management requirements of IPCablecom compliant devices and
functions and how these requirements are supported in the MIB modules. It is intended to support and complement the
actual MIB module documents, which are issued separately. There are currently two sets of the MIB modules that
describe the Management Information Base for the IPCablecom Multimedia Terminal Adapters (MTAs) as per table 1:
• IPCablecom MIBs ([8], [9], [10], [11], [12])
• IETF MIBs ([16], [17], [18]).
The IPCablecom 1.5 compliant MTAs are to implement the IPCablecom MIBs. The IPCablecom 1.5 compliant MTAs
may implement the IETF MIBs.
Table 1: Functional MIB Areas
IPCablecom Specification Phase IPCablecom MIB Modules IETF MIB Modules
NCS Protocol 1.5 Signalling MIB and Signalling Extension Signalling MIB
MIB
MTA Device Provisioning 1.5 MTA MIB and MTA Extension MIB MTA MIB
Codec 1.5 Signalling MIB Signalling MIB
Security 1.5 MTA MIB MTA MIB
Management Event Mechanism 1.5 Management Event MIB Management Event MIB
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 103 161-11: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 11: Media Terminal Adapter
(MTA) device provisioning". ®
[2] ANSI/SCTE 23-3 2010: "DOCSIS 1.1 Part 3: Operations Support System Interface".
NOTE: Available at: http://www.scte.org/documents/pdf/Standards/ANSI_SCTE%2023-3%202010.pdf.
[3] IETF RFC 791: "Internet Protocol, J. Postel", September 1981.
[4] IETF RFC 2011: "SNMPv2 Management Information Base for the Internet Protocol using
SMIv2", K. McCloghrie, November 1996.
[5] IETF RFC 2863: "The Interfaces Group MIB", K. McCloghrie, F. Kastenholz, June 2000.
[6] ANSI/SCTE 107 2009: "Embedded Cable Modem Devices". ®
[7] ANSI/SCTE 79-2 2009: "DOCSIS 2.0 Part 2: Operations Support System Interface".
ETSI
8 ETSI TS 103 161-10 V1.1.1 (2011-10)
[8] ETSI TS 103 161-7: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 7: Media Terminal Adapter
(MTA) Management Information Base (MIB)".".
[9] ETSI TS 103 161-8: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 8: Network Call Signalling
(NCS) MIB Requirements".
[10] ETSI TS 103 161-18: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 18: Media Terminal Adapter
Extension MIB".
[11] ETSI TS 103 161-21: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 21: Signalling Extension MIB
Specification". ®
[12] Cable Television Laboratories, Inc. CL-SP-MIB-BB-I04-100608: "CableLabs Specifications,
Battery Backup MIB", June 8, 2010.
[13] IETF RFC 2578/STD0058: "Structure of Management Information Version 2 (SMIv2)".
[14] ETSI TS 103 161-20: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 20: Management Event MIB
Specification".
[15] IETF RFC 4293: "Management Information Base for the Internet Protocol (IP)", April 2006.
[16] IETF RFC 4682: "Multimedia Terminal Adapter (MTA) Management Information Base for
PacketCable - and IPCablecom-Compliant Devices", December 2006.
[17] IETF RFC 5098: "Signaling MIB for PacketCable and IPCablecom Multimedia Terminal Adapters
(MTAs)", February 2008.
[18] IETF RFC 5428: "Management Event Management Information Base (MIB) for PacketCable- and
IPCablecom-Compliant Devices", April 2009.
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI TS 103 161-2: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 2: Architectural framework for
the delivery of time critical services over Cable Television Networks using Cable Modems". ®
[i.2] Cable Television Laboratories, Inc. CL-SP-MIB-CLABDEF-I09-110210: "CableLabs Definition
MIB Specification", February 10, 2011.
[i.3] IETF RFC 2013: "SNMPv2 MIB for the User Datagram Protocol Using SMIv2".
[i.4] IETF RFC 3418: "Management Information Base (MIB) for the Simple Network Management
Protocol (SNMP)".
[i.5] ETSI TS 103 161-4: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 4: Network Call Signalling
Protocol".
[i.6] ETSI TS 103 161-9: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 9: Security".
[i.7] IETF RFC 3410: "Introduction and Applicability Statements for Internet Standard Management
Framework".
[i.8] IETF RFC 3411: "An Architecture for Describing Simple Network Management Protocol
(SNMP)".
ETSI
9 ETSI TS 103 161-10 V1.1.1 (2011-10)
[i.9] IETF RFC 3412: "Message Processing and Dispatching for the Simple Network Management
IETF RFC 3413/STD0062, Simple Network Management Protocol (SNMP) Applications".
[i.10] IETF RFC 3414/STD0062: "User-based Security Model (USM) for version 3 of the Simple
Network Management Protocol (SNMPv3)".
[i.11] IETF RFC 3415/STD0062: "View-based Access Control Model (VACM) for Simple Network
Management Protocol (SNMP)".
[i.12] IETF RFC 2959: "Real-Time Transport Protocol Management Information Base". .
[i.13] ETSI TS 103 161-3: "Access, Terminals, Transmission and Multiplexing (ATTM); Integrated
Broadband Cable and Television Networks; IPCablecom 1.5; Part 3: Audio Codec Requirements
for the Provision of Bi-Directional Audio Service over Cable Television Networks using Cable
Modems".
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the following terms and definitions apply:
access control: limiting the flow of information from the resources of a system only to authorized persons, programs,
processes, or other system resources on a network
authentication: process of verifying the claimed identity of an entity to another entity
embedded MTA: single node that contains both an MTA and a cable modem
endpoint: Terminal, Gateway or Multipoint Conference Unit (MCU)
gateway: devices bridging between the IPCablecom IP Voice Communication world and the PSTN
Multimedia Terminal Adapter (MTA): device that contains the interface to a physical voice device, a network
interface, CODECs, and all signalling and encapsulation functions required for VoIP transport, class features signalling,
and QoS signalling
network management: functions related to the management of data across the network
Real-time Transport Protocol (RTP): protocol for encapsulating encoded voice and video streams
3.2 Abbreviations
For the purposes of the present document, the following abbreviations apply:
AP Access Point ®
CM DOCSIS Cable Modem
CMS Call Management Server
CODEC COder-DECoder ®
DOCSIS Data-Over-Cable Service Interface Specifications
DSP Digital Signal Processor
DTMF Dual Tone Multi Frequency
E-MTA Embedded MTA
IETF Internet Engineering Task Force
IFMIB Interfaces Group Managed Information Block
IP Internet Protocol
MAC Message Authentication Code
MGPPI Multiple Grants Per Interval
MIB Management Information Base
MTA Multimedia Terminal Adapter
NCS Network Call Signalling
ETSI
10 ETSI TS 103 161-10 V1.1.1 (2011-10)
PSTN Public Switched Telephone Network
QoS Quality of Service
RFC Request for Comments
RTCP Real-Time Control Protocol
RTP Real-time Transport Protocol
SNMP Simple Network Management Protocol
TCP Transmission Control Protocol
UPS Uninterrupted Power Supply
USM User-based Security Model
VACM View Access Control Module
VoIP Voice-over-IP
4 Void
5 Overview
IPCablecom MIB modules are designed to provide necessary functionality defined in IPCablecom 1.5 specifications.
The MIB design follows the same multi-phase schedule as the rest of IPCablecom specifications. Table 1 lists
IPCablecom functional areas that are in scope of IPCablecom 1.5. Additionally, in the present document, the term
® ®
"DOCSIS " is used to refer to DOCSIS version 1.1 or later, unless explicitly specified otherwise.
5.1 IPCablecom Reference Architecture
The conceptual diagram for the IPCablecom architecture is shown in figure 1.
Please refer to the architecture document [i.1] for more detailed information concerning the IPCablecom architecture.
Call
Embedded MTA
Announcement Server
Management
Cable
Server
MTA Announcement Controller
Modem
(CMS )
(ANC)
HFC access
Announcement Player
network CMTS
(AN P)
DOCSIS
( )
Signalling
Gateway
(SG)
Managed IP Network
Media
PSTN
Gateway
Controller
(MGC)
Media
HFC access
Gateway
CMTS
(MG)
network
DOCSIS
( )
Key Distribution Server (KDC)
Embedded MTA
Provisioning Server
Cable
MTA DHCP Servers
Modem OSS
DNS Servers
Backoffice
TFTP or HTTP Servers
SYSLOG Server
Record Keeping Server (RKS)
Figure 1: IPCablecom Reference Architecture
ETSI
11 ETSI TS 103 161-10 V1.1.1 (2011-10)
5.2 General Requirements
The IPCablecom MIBs Framework Specification follows the Internet Standard Management Framework described in
RFC 3410 [i.7]. Additionally, the following requirements have been considered in the design of the IPCableco
...








Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.
Loading comments...