ETSI EN 302 842-2 V1.2.1 (2006-12)

SLOVENSKI STANDARD
01-marec-2007
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
5DGLMVNDRSUHPD]DGLJLWDOQRSRYH]DYR9+)9'/]UDNWODLQ]UDN]UDNQDþLQ
7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH]DDHURQDYWLþQRPRELOQROHWDOVNR
RSUHPRGHO6SORãQLRSLVLQSODVW]DSRGDWNRYQHSRYH]DYH
Electromagnetic compatibility and Radio spectrum Matters (ERM); VHF air-ground and
air-air Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods
of measurement for aeronautical mobile (airborne) equipment; Part 2: General
description and data link layer
Ta slovenski standard je istoveten z: EN 302 842-2 Version 1.2.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
49.090 2SUHPDLQLQVWUXPHQWLY On-board equipment and
]UDþQLKLQYHVROMVNLKSORYLOLK instruments
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
VHF air-ground and air-air Digital Link (VDL)
Mode 4 radio equipment;
Technical characteristics and
methods of measurement
for aeronautical mobile (airborne) equipment;
Part 2: General description and data link layer

2 ETSI EN 302 842-2 V1.2.1 (2006-12)

Reference
REN/ERM-TG25-030-2
Keywords
aeronautical, digital, radio, testing, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2006.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI EN 302 842-2 V1.2.1 (2006-12)
Contents
Intellectual Property Rights.8
Foreword.8
Introduction .9
1 Scope.10
2 References.12
3 Definitions and abbreviations.13
3.1 Definitions.13
3.1.1 Basic reference model definitions.13
3.1.2 Service conventions definitions .13
3.1.3 General definitions.13
3.1.4 Definition of bit order.16
3.2 Abbreviations.17
4 General description of VDL Mode 4 mobile station link layer.18
4.1 General.18
4.1.1 Overview of VDL Mode 4.18
4.1.2 Relationship to OSI reference model.19
4.1.3 VDL Mode 4 services .20
4.1.4 ADS-B function.20
4.1.5 Operational scenarios.21
4.1.6 VDL Mode 4 fundamentals .21
4.1.7 Possible configuration of airborne equipment .22
4.1.8 Classes of equipment .24
4.1.9 Transceiver cross-links.24
4.1.10 Overall structure of specifications for VDL Mode 4 .24
4.1.11 Equipment performance verification .26
5 Minimum performance specification under standard test conditions.27
5.1 MAC sublayer.27
5.1.1 Services.27
5.1.2 MAC sublayer services.27
5.1.3 MAC sublayer parameters .27
5.1.3.1 General.27
5.1.3.2 Parameter M1 (number of slots per superframe).28
5.1.3.3 Parameter M2_inc and M2_limit (MAC layer control parameters for network entry) .28
5.1.3.4 Inspection of m2 filter following transceiver failure.29
5.1.4 Time synchronization.29
5.1.4.1 Primary.29
5.1.4.2 Secondary.29
5.1.4.3 Alignment to UTC second .30
5.1.4.4 Data quality level.30
5.1.5 Slot idle/busy notification.30
5.1.5.1 Slot idle detection.30
5.1.5.2 Slot busy detection .30
5.1.5.3 Slot occupied detection .30
5.1.5.4 Signal level indication.31
5.1.6 Transmission processing.31
5.1.7 Received transmission processing .31
5.2 VSS sublayer.31
5.2.1 Services.32
5.2.1a Multiple access.32
5.2.1.1 Error detection.32
5.2.1.2 Channel congestion.32
5.2.2 Burst format.33
5.2.2.1 VSS burst structure.33
ETSI
4 ETSI EN 302 842-2 V1.2.1 (2006-12)
5.2.2.2 Version number.34
5.2.2.3 Source address.34
5.2.2.4 Message ID.34
5.2.2.5 Information field.35
5.2.2.6 Reservation fields.35
5.2.2.7 Autonomous/directed flag.35
5.2.3 VSS sublayer parameters .36
5.2.3.1 General.36
5.2.3.2 Parameter VS1 (number of ground quarantined slots) .36
5.2.3.3 Parameter VS2 (minimum CCI performance).37
5.2.3.4 Parameter VS4 (quarantine slot re-use range).37
5.2.3.5 Parameter VS5 (maximum burst length).37
5.2.4 VSS quality of service parameters.37
5.2.4.1 General.37
5.2.4.2 Parameter Q1 (priority) .38
5.2.4.3 Parameters Q2a to Q2d (slot selection range constraint for level n) .39
5.2.4.4 Parameter Q3 (replace queued data) .39
5.2.4.5 Parameter Q4 (number of available slots).40
5.2.5 Received transmission processing .40
5.2.6 Reserved access protocol specification.41
5.2.6.1 Reservation table.41
5.2.6.2 Selecting slots for transmission or reservation.42
5.2.6.3 Reserved transmissions.43
5.2.6.4 Reservation conflicts.44
5.2.6.5 Transmission conflicts for mobile stations.44
5.2.7 Random access protocol specification .45
5.2.7.1 General.45
5.2.7.2 Random access parameters.45
5.2.7.3 Random access procedures.47
5.2.8 Void.48
5.2.9 Null reservation protocol specification.48
5.2.9.1 Null reservation burst format .48
5.2.10 Periodic broadcast protocol specification .48
5.2.10.1 Periodic broadcast reservation burst format.48
5.2.10.2 Periodic broadcast timers.49
5.2.10.3 Periodic broadcast parameters.49
5.2.10.4 Periodic broadcast reception procedures.50
5.2.10.5 Periodic broadcast transmission procedures.51
5.2.11 Incremental broadcast protocol specification .54
5.2.11.1 Incremental broadcast reservation burst format .54
5.2.11.2 Incremental broadcast parameters.54
5.2.11.3 Incremental broadcast reception procedures .55
5.2.11.4 Incremental broadcast transmission procedures.55
5.2.12 Combined periodic broadcast and incremental broadcast protocol specification .56
5.2.12.1 Combined periodic broadcast and incremental broadcast reservation burst.56
5.2.13 Big negative dither (BND) broadcast protocol specifications .56
5.2.13.1 BND reservation burst format.56
5.2.13.2 BND broadcast parameters.57
5.2.13.3 BND broadcast reception procedures.57
5.2.13.4 BND broadcast transmission procedures .57
5.2.14 Unicast request protocol specification .57
5.2.14.1 Unicast request reservation burst format.57
5.2.14.1a Unicast request parameters.58
5.2.14.2 Unicast request reception procedures.59
5.2.14.3 Unicast request transmission procedures .60
5.2.15 Information transfer request protocol specification .60
5.2.15.1 Information transfer request reservation burst format.60
5.2.15.2 Information transfer request reception procedures.62
5.2.16 Directed request protocol specification.62
5.2.16.1 Directed request reservation burst format .62
5.2.16.2 Directed request parameters.65
5.2.16.3 Directed request reception procedures .66
ETSI
5 ETSI EN 302 842-2 V1.2.1 (2006-12)
5.2.16.4 Directed request transmission procedures.67
5.2.16.5 Directed request response procedures .68
5.2.17 Block reservation protocols specification.69
5.2.17.1 Superframe block reservation burst format .69
5.2.17.2 Second frame block reservation burst format.70
5.2.17.3 Void.71
5.2.17.4 Superframe block reservation reception procedures .71
5.2.17.5 Second frame block reservation parameters.73
5.2.17.6 Second frame block reservation reception procedures.73
5.2.17.7 Void.73
5.2.17.7a Procedures for responding to a rebroadcast request for superframe block reservation .73
5.2.18 Response protocol specification .74
5.2.18.1 Response burst format.74
5.2.19 General request protocol specification.74
5.2.19.1 General request burst format.74
5.2.19.2 General request procedures .75
5.2.20 General response protocol specification .75
5.2.20.1 General response burst format.75
5.2.20.2 General response procedures.77
5.2.21 Retransmission procedures.77
5.3 DLS sublayer.78
5.3.1 Services.78
5.3.1.1 General.78
5.3.1.2 Data transfer.78
5.3.1.3 Station address encoding.78
5.3.1.4 DLS burst formats.79
5.3.2 DLS system parameters.81
5.3.2.1 Parameter ND4 (maximum length of a UDATA burst) .81
5.3.3 DLS procedures.81
5.3.3.1 Broadcast.81
5.3.3.2 DLS not supported.81
5.3.3.3 User data packet reception .82
5.3.3.4 CTRL DLPDU.82
5.4 Link Management Entity (LME) sublayer .82
5.4.1 Services.82
5.4.2 Synchronization burst format.82
5.4.2.1 General.82
5.4.2.2 Fixed and variable data fields.82
5.4.2.3 Fixed data field format .83
5.4.2.4 Variable data field format .86
5.4.2.5 Synchronization burst request .86
5.4.2.6 Broadcast link management burst .86
5.4.3 Control (CTRL) parameter formats .87
5.4.3.1 Encoding.87
5.4.3.2 VDL Mode 4 parameter identification .87
5.4.3.3 Ground-initiated modification parameters .88
5.4.3.4 Ground-initiated information parameters.91
5.4.3a LME timers and parameters.93
5.4.3a.1 General.93
5.4.3a.2 Counter L1 (maximum number of missed reservations) and Timer TL3 (inter-miss timer).94
5.4.4 LME procedures.94
5.4.4.1 Synchronization burst procedures .94
5.4.4.2 Peer Entity Contact Table (PECT).97
5.4.4.3 Network entry protocol specifications .98
5.4.5 Additional material for ADS-B applications .104
5.4.5.1 Information field formats.104
5.4.5.2 ADS-B request format.105
5.5 Void.105
5.6 Definitions for Compact Position Reporting .105
5.6.1 Introduction.105
5.6.2 Parameter symbols, data types, constants and variables .105
5.6.2.1 Parameter symbols.105
ETSI
6 ETSI EN 302 842-2 V1.2.1 (2006-12)
5.6.2.2 Data types.106
5.6.2.3 Constants.106
5.6.2.4 Variables.106
5.6.2.5 Functions.107
5.6.2.6 Patch constants.108
5.6.3 Fixed data field position encoding.110
5.6.3.1 General.110
5.6.3.2 Input parameters.110
5.6.3.3 Calculations.110
5.6.4 Fixed data field position local decoding .111
5.6.4.1 General.111
5.6.4.2 Input parameters.111
5.6.4.3 Calculations.111
5.6.5 Fixed data field position global decoding.112
5.6.5.1 General.112
5.6.5.2 Input parameters.113
5.6.5.3 Transition level straddling.113
5.6.5.4 Calculations.113
5.6.6 Position Report Processing .114
5.6.6.1 Services.114
5.6.6.2 Position report parameters.114
5.6.6.3 Position report processing procedures.115
6 General design requirements.117
6.1 Controls and indicators.117
6.2 Warm up.117
6.3 Airworthiness.117
6.4 Intended function.117
6.5 International Telecommunications Union regulations.117
6.6 Fire protection.118
6.7 Operation of controls.118
6.8 Accessibility of controls.118
6.9 Effects of tests .118
6.10 Failure of the VDL Mode 4 equipment .118
6.11 Software management.118
6.12 Transceiver configuration.118
6.13 Provision for multiple redundant VDL4 transceivers.118
6.14 Reception capability.118
6.15 Transmission capability.118
6.16 Monitoring of proper operation .118
6.17 Power-up self test .118
7 Protocol test procedures.119
7.1 General.119
7.1.1 Input voltage.119
7.1.2 Power input frequency.119
7.1.3 Adjustment of equipment.119
7.1.4 Equipment configuration.119
7.1.5 Test equipment precautions .119
7.1.6 Ambient conditions.119
7.1.7 Connected loads.119
7.2 Required test rig .119
7.3 Protocol test-suite description methodology .122
7.4 Detailed protocol test procedures .122
7.4.1 Test-suite overview.122
7.4.2 Declarations.129
7.4.3 Constraints.129
7.4.3.1 Abbreviations.129
7.4.3.1.1 Subfield mnemonics.129
7.4.3.1.2 Special characters used in the subfield definitions .130
7.4.3.1.3 Station addresses and positions .130
7.4.3.1.4 Tables of values for use in CPR test cases .131
ETSI
7 ETSI EN 302 842-2 V1.2.1 (2006-12)
7.4.3.1.5 Tables of values for use in content checking test cases .143
7.4.3.1.6 VDL4 burst formats.145
7.4.3.2 Test cases.167
7.4.3.2.1 Test case macros.168
7.4.3.2.2 Test case descriptions .170
Annex A (informative): Cross reference matrix .393
Annex B (informative): Description of ISO/IEC 9646 test methodology .411
B.1 Overview of the structure of the ISO/IEC 9646 test-suites.411
B.2 The test case description.411
B.3 The queue action .413
B.4 The repeat construct .413
B.5 Macro definitions.414
B.6 Test case naming.414
Annex C (informative): Bibliography.415
History .421

ETSI
8 ETSI EN 302 842-2 V1.2.1 (2006-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document is part 2 of a multi-part deliverable covering the VHF air-ground and air-air Digital Link (VDL)
Mode 4 radio equipment; Technical characteristics and methods of measurement for aeronautical mobile (airborne)
equipment, as identified below:
Part 1: "Physical layer";
Part 2: "General description and data link layer";
Part 3: "Additional broadcast aspects";
Part 4: "Point-to-point functions";
Part 5: "VDL4 airbone equipment in compliance with the SES 552/2004 interoperability Regulation".
The present document is accompanied by an equivalent ground-based standard, EN
...