ETSI EN 300 328 V1.9.0 (2014-12)

ETSI EN 300 328 V1.9.1 (2015-02)






HARMONIZED EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 ETSI EN 300 328 V1.9.1 (2015-02)



Reference
REN/ERM-TG11-010
Keywords
data, ISM, LAN, mobile, radio, regulation, spread
spectrum, SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2015.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 328 V1.9.1 (2015-02)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical specifications . 14
4.1 Environmental profile . 14
4.2 Equipment types . 14
4.2.1 Modulation types . 14
4.2.2 Adaptive and non-adaptive equipment . 14
4.3 Technical requirements . 15
4.3.1 Technical requirements for Frequency Hopping equipment . 15
4.3.1.1 Introduction . 15
4.3.1.2 RF output power . 15
4.3.1.2.1 Applicability . 15
4.3.1.2.2 Definition. 15
4.3.1.2.3 Limit . 15
4.3.1.2.4 Conformance . 15
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 15
4.3.1.3.1 Applicability . 15
4.3.1.3.2 Definition. 16
4.3.1.3.3 Limit . 16
4.3.1.3.4 Conformance . 16
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 16
4.3.1.4.1 Applicability . 16
4.3.1.4.2 Definition. 16
4.3.1.4.3 Limit . 16
4.3.1.4.4 Other Requirements . 17
4.3.1.4.5 Conformance . 17
4.3.1.5 Hopping Frequency Separation . 18
4.3.1.5.1 Applicability . 18
4.3.1.5.2 Definition. 18
4.3.1.5.3 Limit . 18
4.3.1.5.4 Conformance . 18
4.3.1.6 Medium Utilization (MU) factor . 18
4.3.1.6.1 Applicability . 18
4.3.1.6.2 Definition. 19
4.3.1.6.3 Limit . 19
4.3.1.6.4 Conformance . 19
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 19
4.3.1.7.1 Applicability . 19
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 19
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 20
4.3.1.7.4 Short Control Signalling Transmissions . 21
4.3.1.8 Occupied Channel Bandwidth . 22
4.3.1.8.1 Applicability . 22
ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 328 V1.9.1 (2015-02)
4.3.1.8.2 Definition. 22
4.3.1.8.3 Limits . 22
4.3.1.8.4 Conformance . 22
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 22
4.3.1.9.1 Applicability . 22
4.3.1.9.2 Definition. 22
4.3.1.9.3 Limit . 22
4.3.1.9.4 Conformance . 23
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 23
4.3.1.10.1 Applicability . 23
4.3.1.10.2 Definition. 23
4.3.1.10.3 Limit . 23
4.3.1.10.4 Conformance . 23
4.3.1.11 Receiver spurious emissions . 24
4.3.1.11.1 Applicability . 24
4.3.1.11.2 Definition. 24
4.3.1.11.3 Limit . 24
4.3.1.11.4 Conformance . 24
4.3.1.12 Receiver Blocking . 24
4.3.1.12.1 Applicability . 24
4.3.1.12.2 Definition. 24
4.3.1.12.3 Limits . 24
4.3.1.12.4 Conformance . 25
4.3.1.13 Geo-location capability . 25
4.3.1.13.1 Applicability . 25
4.3.1.13.2 Definition. 25
4.3.1.13.3 Requirements . 25
4.3.2 Technical requirements for other types of Wide Band modulation . 25
4.3.2.1 Introduction . 25
4.3.2.2 RF output power . 25
4.3.2.2.1 Applicability . 25
4.3.2.2.2 Definition. 26
4.3.2.2.3 Limit . 26
4.3.2.2.4 Conformance . 26
4.3.2.3 Power Spectral Density . 26
4.3.2.3.1 Applicability . 26
4.3.2.3.2 Definition. 26
4.3.2.3.3 Limit . 26
4.3.2.3.4 Conformance . 26
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 26
4.3.2.4.1 Applicability . 26
4.3.2.4.2 Definition. 27
4.3.2.4.3 Limit . 27
4.3.2.4.4 Conformance . 27
4.3.2.5 Medium Utilization (MU) factor . 27
4.3.2.5.1 Applicability . 27
4.3.2.5.2 Definition. 27
4.3.2.5.3 Limit . 27
4.3.2.5.4 Conformance . 27
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 28
4.3.2.6.1 Applicability . 28
4.3.2.6.2 Non-LBT based Detect and Avoid . 28
4.3.2.6.3 LBT based Detect and Avoid . 28
4.3.2.6.4 Short Control Signalling Transmissions . 31
4.3.2.7 Occupied Channel Bandwidth . 31
4.3.2.7.1 Applicability . 31
4.3.2.7.2 Definition. 31
4.3.2.7.3 Limits . 31
4.3.2.7.4 Conformance . 31
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 31
4.3.2.8.1 Applicability . 31
4.3.2.8.2 Definition. 32
ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 328 V1.9.1 (2015-02)
4.3.2.8.3 Limit . 32
4.3.2.8.4 Conformance . 32
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 32
4.3.2.9.1 Applicability . 32
4.3.2.9.2 Definition. 32
4.3.2.9.3 Limit . 32
4.3.2.9.4 Conformance . 33
4.3.2.10 Receiver spurious emissions . 33
4.3.2.10.1 Applicability . 33
4.3.2.10.2 Definition. 33
4.3.2.10.3 Limit . 33
4.3.2.10.4 Conformance . 33
4.3.2.11 Receiver Blocking . 33
4.3.2.11.1 Applicability . 33
4.3.2.11.2 Definition. 34
4.3.2.11.3 Limits . 34
4.3.2.11.4 Conformance . 34
4.3.2.12 Geo-location capability . 34
4.3.2.12.1 Applicability . 34
4.3.2.12.2 Definition. 34
4.3.2.12.3 Requirements . 34
5 Essential radio test suites . 35
5.1 Conditions for testing . 35
5.1.1 Normal and extreme test conditions. 35
5.1.1.1 Introduction . 35
5.1.1.2 Normal test conditions . 35
5.1.1.2.1 Normal temperature and humidity . 35
5.1.1.2.2 Normal power source . 35
5.1.1.3 Extreme test conditions . 35
5.1.1.3.1 Extreme temperatures . 35
5.1.2 Test mode. 35
5.1.3 Antennas and transmit operating modes . 35
5.1.3.1 Integrated and dedicated antennas . 35
5.1.3.2 Smart antenna systems and related operating modes . 36
5.1.3.2.1 Introduction . 36
5.1.3.2.2 Operating mode 1 (single antenna) . 36
5.1.3.2.3 Operating mode 2 (multiple antennas, no beamforming) . 36
5.1.3.2.4 Operating mode 3 (multiple antennas, with beamforming) . 36
5.1.3.3 Output power setting . 36
5.1.4 Adaptive and Non-adaptive equipment. 36
5.1.5 Presentation of equipment . 37
5.1.5.1 Testing of stand-alone equipment . 37
5.1.5.2 Testing of host connected equipment and plug-in radio equipment . 37
5.1.5.2.1 Introduction . 37
5.1.5.2.2 The use of a host or test jig for testing Plug-In radio equipment . 37
5.1.5.2.3 Testing of combinations . 37
5.1.6 Test Fixture . 38
5.2 Interpretation of the measurement results . 38
5.3 Test procedures for essential radio test suites. 39
5.3.1 Product Information . 39
5.3.2 RF output power, Duty Cycle, Tx-sequence, Tx-gap, Medium Utilization . 40
5.3.2.1 Test conditions . 40
5.3.2.2 Test method . 40
5.3.2.2.1 Conducted measurements . 40
5.3.2.2.2 Radiated measurements . 43
5.3.3 Power Spectral Density . 43
5.3.3.1 Test conditions . 43
5.3.3.2 Te
...

Final draft ETSI EN 300 328 V1.9.0 (2014-12)






HARMONIZED EUROPEAN STANDARD
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 300 328 V1.9.0 (2014-12)



Reference
REN/ERM-TG11-010
Keywords
data, ISM, LAN, mobile, radio, regulation, spread
spectrum, SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 300 328 V1.9.0 (2014-12)
Contents
Intellectual Property Rights . 8
Foreword . 8
Modal verbs terminology . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 11
3.1 Definitions . 11
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical specifications . 14
4.1 Environmental profile . 14
4.2 Equipment types . 14
4.2.1 Modulation types . 14
4.2.2 Adaptive and non-adaptive equipment . 14
4.3 Technical requirements . 15
4.3.1 Technical requirements for Frequency Hopping equipment . 15
4.3.1.1 Introduction . 15
4.3.1.2 RF output power . 15
4.3.1.2.1 Applicability . 15
4.3.1.2.2 Definition. 15
4.3.1.2.3 Limit . 15
4.3.1.2.4 Conformance . 15
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 15
4.3.1.3.1 Applicability . 15
4.3.1.3.2 Definition. 16
4.3.1.3.3 Limit . 16
4.3.1.3.4 Conformance . 16
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 16
4.3.1.4.1 Applicability . 16
4.3.1.4.2 Definition. 16
4.3.1.4.3 Limit . 16
4.3.1.4.4 Other Requirements . 17
4.3.1.4.5 Conformance . 17
4.3.1.5 Hopping Frequency Separation . 18
4.3.1.5.1 Applicability . 18
4.3.1.5.2 Definition. 18
4.3.1.5.3 Limit . 18
4.3.1.5.4 Conformance . 18
4.3.1.6 Medium Utilization (MU) factor . 18
4.3.1.6.1 Applicability . 18
4.3.1.6.2 Definition. 19
4.3.1.6.3 Limit . 19
4.3.1.6.4 Conformance . 19
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 19
4.3.1.7.1 Applicability . 19
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 19
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 20
4.3.1.7.4 Short Control Signalling Transmissions . 21
4.3.1.8 Occupied Channel Bandwidth . 22
4.3.1.8.1 Applicability . 22
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 300 328 V1.9.0 (2014-12)
4.3.1.8.2 Definition. 22
4.3.1.8.3 Limits . 22
4.3.1.8.4 Conformance . 22
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 22
4.3.1.9.1 Applicability . 22
4.3.1.9.2 Definition. 22
4.3.1.9.3 Limit . 22
4.3.1.9.4 Conformance . 23
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 23
4.3.1.10.1 Applicability . 23
4.3.1.10.2 Definition. 23
4.3.1.10.3 Limit . 23
4.3.1.10.4 Conformance . 23
4.3.1.11 Receiver spurious emissions . 24
4.3.1.11.1 Applicability . 24
4.3.1.11.2 Definition. 24
4.3.1.11.3 Limit . 24
4.3.1.11.4 Conformance . 24
4.3.1.12 Receiver Blocking . 24
4.3.1.12.1 Applicability . 24
4.3.1.12.2 Definition. 24
4.3.1.12.3 Limits . 24
4.3.1.12.4 Conformance . 25
4.3.1.13 Geo-location capability . 25
4.3.1.13.1 Applicability . 25
4.3.1.13.2 Definition. 25
4.3.1.13.3 Requirements . 25
4.3.2 Technical requirements for other types of Wide Band modulation . 25
4.3.2.1 Introduction . 25
4.3.2.2 RF output power . 25
4.3.2.2.1 Applicability . 25
4.3.2.2.2 Definition. 26
4.3.2.2.3 Limit . 26
4.3.2.2.4 Conformance . 26
4.3.2.3 Power Spectral Density . 26
4.3.2.3.1 Applicability . 26
4.3.2.3.2 Definition. 26
4.3.2.3.3 Limit . 26
4.3.2.3.4 Conformance . 26
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 26
4.3.2.4.1 Applicability . 26
4.3.2.4.2 Definition. 27
4.3.2.4.3 Limit . 27
4.3.2.4.4 Conformance . 27
4.3.2.5 Medium Utilization (MU) factor . 27
4.3.2.5.1 Applicability . 27
4.3.2.5.2 Definition. 27
4.3.2.5.3 Limit . 27
4.3.2.5.4 Conformance . 27
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 28
4.3.2.6.1 Applicability . 28
4.3.2.6.2 Non-LBT based Detect and Avoid . 28
4.3.2.6.3 LBT based Detect and Avoid . 28
4.3.2.6.4 Short Control Signalling Transmissions . 31
4.3.2.7 Occupied Channel Bandwidth . 31
4.3.2.7.1 Applicability . 31
4.3.2.7.2 Definition. 31
4.3.2.7.3 Limits . 31
4.3.2.7.4 Conformance . 31
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 31
4.3.2.8.1 Applicability . 31
4.3.2.8.2 Definition. 32
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 300 328 V1.9.0 (2014-12)
4.3.2.8.3 Limit . 32
4.3.2.8.4 Conformance . 32
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 32
4.3.2.9.1 Applicability . 32
4.3.2.9.2 Definition. 32
4.3.2.9.3 Limit . 32
4.3.2.9.4 Conformance . 33
4.3.2.10 Receiver spurious emissions . 33
4.3.2.10.1 Applicability . 33
4.3.2.10.2 Definition. 33
4.3.2.10.3 Limit . 33
4.3.2.10.4 Conformance . 33
4.3.2.11 Receiver Blocking . 33
4.3.2.11.1 Applicability . 33
4.3.2.11.2 Definition. 34
4.3.2.11.3 Limits . 34
4.3.2.11.4 Conformance . 34
4.3.2.12 Geo-location capability . 34
4.3.2.12.1 Applicability . 34
4.3.2.12.2 Definition. 34
4.3.2.12.3 Requirements . 34
5 Essential radio test suites . 35
5.1 Conditions for testing . 35
5.1.1 Normal and extreme test conditions. 35
5.1.1.1 Introduction . 35
5.1.1.2 Normal test conditions . 35
5.1.1.2.1 Normal temperature and humidity . 35
5.1.1.2.2 Normal power source . 35
5.1.1.3 Extreme test conditions . 35
5.1.1.3.1 Extreme temperatures . 35
5.1.2 Test mode. 35
5.1.3 Antennas and transmit operating modes . 35
5.1.3.1 Integrated and dedicated antennas . 35
5.1.3.2 Smart antenna systems and related operating modes . 36
5.1.3.2.1 Introduction . 36
5.1.3.2.2 Operating mode 1 (single antenna) . 36
5.1.3.2.3 Operating mode 2 (multiple antennas, no beamforming) . 36
5.1.3.2.4 Operating mode 3 (multiple antennas, with beamforming) . 36
5.1.3.3 Output power setting . 36
5.1.4 Adaptive and Non-adaptive equipment. 36
5.1.5 Presentation of equipment . 37
5.1.5.1 Testing of stand-alone equipment . 37
5.1.5.2 Testing of host connected equipment and plug-in radio equipment . 37
5.1.5.2.1 Introduction . 37
5.1.5.2.2 The use of a host or test jig for testing Plug-In radio equipment . 37
5.1.5.2.3 Testing of combinations . 37
5.1.6 Test Fixture . 38
5.2 Interpretation of the measurement results . 38
5.3 Test procedures for essential radio test suites. 39
5.3.1 Product Information . 39
5.3.2 RF output power, Duty Cycle, Tx-sequence, Tx-gap, Medium Utilization . 40
5.3.2.1 Test conditions . 40
5.3.2.2 Test method . 40
5.3.2.2.1 Conducted measurements . 40
5.3.2.2.2 Radiated measurements . 43
5.3.3 Power Spectral Density . 43
5.3.3.1 Test conditions .
...

Draft ETSI EN 300 328 V1.8.2 (2014-04)






Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 328 V1.8.2 (2014-04)



Reference
REN/ERM-TG11-010
Keywords
data, ISM, LAN, mobile, radio, regulation, spread
spectrum, SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 328 V1.8.2 (2014-04)
Contents
Intellectual Property Rights . 8
Foreword . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical specifications . 14
4.1 Environmental profile . 14
4.2 Equipment types . 14
4.2.1 Modulation types . 14
4.2.2 Adaptive and non-adaptive equipment . 14
4.3 Technical requirements . 15
4.3.1 Technical requirements for Frequency Hopping equipment . 15
4.3.1.1 Introduction . 15
4.3.1.2 RF output power . 15
4.3.1.2.1 Applicability . 15
4.3.1.2.2 Definition. 15
4.3.1.2.3 Limit . 15
4.3.1.2.4 Conformance . 15
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 15
4.3.1.3.1 Applicability . 15
4.3.1.3.2 Definition. 15
4.3.1.3.3 Limit . 16
4.3.1.3.4 Conformance . 16
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 16
4.3.1.4.1 Applicability . 16
4.3.1.4.2 Definition. 16
4.3.1.4.3 Limit . 16
4.3.1.4.4 Other Requirements . 17
4.3.1.4.5 Conformance . 17
4.3.1.5 Hopping Frequency Separation . 17
4.3.1.5.1 Applicability . 17
4.3.1.5.2 Definition. 17
4.3.1.5.3 Limit . 18
4.3.1.5.4 Conformance . 18
4.3.1.6 Medium Utilization (MU) factor . 18
4.3.1.6.1 Applicability . 18
4.3.1.6.2 Definition. 18
4.3.1.6.3 Limit . 18
4.3.1.6.4 Conformance . 19
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 19
4.3.1.7.1 Applicability . 19
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 19
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 20
4.3.1.7.4 Short Control Signalling Transmissions . 21
4.3.1.8 Occupied Channel Bandwidth . 21
4.3.1.8.1 Applicability . 21
4.3.1.8.2 Definition. 21
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 328 V1.8.2 (2014-04)
4.3.1.8.3 Limits . 21
4.3.1.8.4 Conformance . 21
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 22
4.3.1.9.1 Applicability . 22
4.3.1.9.2 Definition. 22
4.3.1.9.3 Limit . 22
4.3.1.9.4 Conformance . 22
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 22
4.3.1.10.1 Applicability . 22
4.3.1.10.2 Definition. 22
4.3.1.10.3 Limit . 23
4.3.1.10.4 Conformance . 23
4.3.1.11 Receiver spurious emissions . 23
4.3.1.11.1 Applicability . 23
4.3.1.11.2 Definition. 23
4.3.1.11.3 Limit . 23
4.3.1.11.4 Conformance . 23
4.3.1.12 Receiver Blocking . 24
4.3.1.12.1 Applicability . 24
4.3.1.12.2 Definition. 24
4.3.1.12.3 Limits . 24
4.3.1.12.4 Conformance . 24
4.3.2 Technical requirements for other types of Wide Band modulation . 24
4.3.2.1 Introduction . 24
4.3.2.2 RF output power . 24
4.3.2.2.1 Applicability . 24
4.3.2.2.2 Definition. 25
4.3.2.2.3 Limit . 25
4.3.2.2.4 Conformance . 25
4.3.2.3 Power Spectral Density . 25
4.3.2.3.1 Applicability . 25
4.3.2.3.2 Definition. 25
4.3.2.3.3 Limit . 25
4.3.2.3.4 Conformance . 25
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 25
4.3.2.4.1 Applicability . 25
4.3.2.4.2 Definition. 25
4.3.2.4.3 Limit . 26
4.3.2.4.4 Conformance . 26
4.3.2.5 Medium Utilization (MU) factor . 26
4.3.2.5.1 Applicability . 26
4.3.2.5.2 Definition. 26
4.3.2.5.3 Limit . 26
4.3.2.5.4 Conformance . 26
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 26
4.3.2.6.1 Applicability . 26
4.3.2.6.2 Non-LBT based Detect and Avoid . 27
4.3.2.6.3 LBT based Detect and Avoid . 27
4.3.2.6.4 Short Control Signalling Transmissions . 29
4.3.2.7 Occupied Channel Bandwidth . 30
4.3.2.7.1 Applicability . 30
4.3.2.7.2 Definition. 30
4.3.2.7.3 Limits . 30
4.3.2.7.4 Conformance . 30
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 30
4.3.2.8.1 Applicability . 30
4.3.2.8.2 Definition. 30
4.3.2.8.3 Limit . 30
4.3.2.8.4 Conformance . 31
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 31
4.3.2.9.1 Applicability . 31
4.3.2.9.2 Definition. 31
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 328 V1.8.2 (2014-04)
4.3.2.9.3 Limit . 31
4.3.2.9.4 Conformance . 31
4.3.2.10 Receiver spurious emissions . 32
4.3.2.10.1 Applicability . 32
4.3.2.10.2 Definition. 32
4.3.2.10.3 Limit . 32
4.3.2.10.4 Conformance . 32
4.3.2.11 Receiver Blocking . 32
4.3.2.11.1 Applicability . 32
4.3.2.11.2 Definition. 32
4.3.2.11.3 Limits . 32
4.3.2.11.4 Conformance . 33
5 Essential radio test suites . 33
5.1 Conditions for testing . 33
5.1.1 Normal and extreme test conditions. 33
5.1.1.1 Introduction . 33
5.1.1.2 Normal test conditions . 33
5.1.1.2.1 Normal temperature and humidity . 33
5.1.1.2.2 Normal power source . 33
5.1.1.3 Extreme test conditions . 33
5.1.1.3.1 Extreme temperatures . 33
5.1.1.3.2 Extreme power source voltages . 33
5.1.2 Test mode. 34
5.1.3 Antennas and transmit operating modes . 34
5.1.3.1 Integrated and dedicated antennas . 34
5.1.3.2 Smart antenna systems and related operating modes . 34
5.1.3.2.1 Introduction . 34
5.1.3.2.2 Operating mode 1 (single antenna) . 34
5.1.3.2.3 Operating mode 2 (multiple antennas, no beamforming) . 35
5.1.3.2.4 Operating mode 3 (multiple antennas, with beamforming) . 35
5.1.3.3 Output power setting . 35
5.1.4 Adaptive and Non-adaptive equipment. 35
5.1.5 Presentation of equipment . 35
5.1.5.1 Testing of stand-alone equipment . 35
5.1.5.2 Testing of host connected equipment and plug-in radio equipment . 35
5.1.5.2.1 Introduction . 35
5.1.5.2.2 The use of a host or test jig for testing Plug-In radio equipment . 35
5.1.5.2.3 Testing of combinations . 36
5.1.6 Test Fixture . 36
5.2 Interpretation of the measurement results . 37
5.3 Test procedures for essential radio test suites. 37
5.3.1 Product Information . 37
5.3.2 RF output power, Duty Cycle, Tx-sequence, Tx-gap, Medium Utilization . 38
5.3.2.1 Test conditions . 38
5.3.2.2 Test method . 39
5.3.2.2.1 Conducted measurements . 39
5.3.2.2.2 Radiated measurements . 41
5.3.3 Power Spectral Density . 41
5.3.3.1 Test conditions . 41
5.3.3.2 Test method . 41
5.3.3.2.1 Conducted measurement. 41
5.3.3.2.2 Radiated measurement . 43
5.3.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 43
5.3.4.1 Test conditions . 43
5.3.4.2 Test method . 43
5.3.4.2.1 Conducted measurements . 43
5.3.4.2.2 Radiated measurements . 45
5.3.5 Hopping Frequency Separation.
...

SLOVENSKI STANDARD
oSIST prEN 300 328 V1.8.2:2014
01-junij-2014
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
âLURNRSDVRYQLSUHQRVQLVLVWHPL2SUHPD]DSUHQRVSRGDWNRYYIUHNYHQþQHPSDVX
*+],60NLXSRUDEOMDãLURNRSDVRYQHPRGXODFLMVNHWHKQLNH+DUPRQL]LUDQL(1
NL]DMHPDELVWYHQH]DKWHYHþOHQDGLUHNWLYH5 77(
Electromagnetic compatibility and Radio spectrum Matters (ERM) - Wideband
transmission systems - Data transmission equipment operating in the 2,4 GHz ISM band
and using wide band modulation techniques - Harmonized EN covering the essential
requirements of article 3.2 of the R&TTE Directive
Ta slovenski standard je istoveten z: EN 300 328 Version 1.8.2
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
oSIST prEN 300 328 V1.8.2:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 300 328 V1.8.2:2014

---------------------- Page: 2 ----------------------
oSIST prEN 300 328 V1.8.2:2014
Draft ETSI EN 300 328 V1.8.2 (2014-04)






Harmonized European Standard
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Wideband transmission systems;
Data transmission equipment operating
in the 2,4 GHz ISM band and
using wide band modulation techniques;
Harmonized EN covering the essential requirements
of article 3.2 of the R&TTE Directive

---------------------- Page: 3 ----------------------
oSIST prEN 300 328 V1.8.2:2014
 2 Draft ETSI EN 300 328 V1.8.2 (2014-04)



Reference
REN/ERM-TG11-010
Keywords
data, ISM, LAN, mobile, radio, regulation, spread
spectrum, SRD, testing, transmission, UHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 300 328 V1.8.2:2014
 3 Draft ETSI EN 300 328 V1.8.2 (2014-04)
Contents
Intellectual Property Rights . 8
Foreword . 8
Introduction . 8
1 Scope . 9
2 References . 9
2.1 Normative references . 9
2.2 Informative references . 10
3 Definitions, symbols and abbreviations . 10
3.1 Definitions . 10
3.2 Symbols . 13
3.3 Abbreviations . 13
4 Technical specifications . 14
4.1 Environmental profile . 14
4.2 Equipment types . 14
4.2.1 Modulation types . 14
4.2.2 Adaptive and non-adaptive equipment . 14
4.3 Technical requirements . 15
4.3.1 Technical requirements for Frequency Hopping equipment . 15
4.3.1.1 Introduction . 15
4.3.1.2 RF output power . 15
4.3.1.2.1 Applicability . 15
4.3.1.2.2 Definition. 15
4.3.1.2.3 Limit . 15
4.3.1.2.4 Conformance . 15
4.3.1.3 Duty Cycle, Tx-sequence, Tx-gap . 15
4.3.1.3.1 Applicability . 15
4.3.1.3.2 Definition. 15
4.3.1.3.3 Limit . 16
4.3.1.3.4 Conformance . 16
4.3.1.4 Accumulated Transmit Time, Frequency Occupation and Hopping Sequence . 16
4.3.1.4.1 Applicability . 16
4.3.1.4.2 Definition. 16
4.3.1.4.3 Limit . 16
4.3.1.4.4 Other Requirements . 17
4.3.1.4.5 Conformance . 17
4.3.1.5 Hopping Frequency Separation . 17
4.3.1.5.1 Applicability . 17
4.3.1.5.2 Definition. 17
4.3.1.5.3 Limit . 18
4.3.1.5.4 Conformance . 18
4.3.1.6 Medium Utilization (MU) factor . 18
4.3.1.6.1 Applicability . 18
4.3.1.6.2 Definition. 18
4.3.1.6.3 Limit . 18
4.3.1.6.4 Conformance . 19
4.3.1.7 Adaptivity (Adaptive Frequency Hopping) . 19
4.3.1.7.1 Applicability . 19
4.3.1.7.2 Adaptive Frequency Hopping using LBT based DAA . 19
4.3.1.7.3 Adaptive Frequency Hopping using other forms of DAA (non-LBT based) . 20
4.3.1.7.4 Short Control Signalling Transmissions . 21
4.3.1.8 Occupied Channel Bandwidth . 21
4.3.1.8.1 Applicability . 21
4.3.1.8.2 Definition. 21
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 300 328 V1.8.2:2014
 4 Draft ETSI EN 300 328 V1.8.2 (2014-04)
4.3.1.8.3 Limits . 21
4.3.1.8.4 Conformance . 21
4.3.1.9 Transmitter unwanted emissions in the out-of-band domain . 22
4.3.1.9.1 Applicability . 22
4.3.1.9.2 Definition. 22
4.3.1.9.3 Limit . 22
4.3.1.9.4 Conformance . 22
4.3.1.10 Transmitter unwanted emissions in the spurious domain . 22
4.3.1.10.1 Applicability . 22
4.3.1.10.2 Definition. 22
4.3.1.10.3 Limit . 23
4.3.1.10.4 Conformance . 23
4.3.1.11 Receiver spurious emissions . 23
4.3.1.11.1 Applicability . 23
4.3.1.11.2 Definition. 23
4.3.1.11.3 Limit . 23
4.3.1.11.4 Conformance . 23
4.3.1.12 Receiver Blocking . 24
4.3.1.12.1 Applicability . 24
4.3.1.12.2 Definition. 24
4.3.1.12.3 Limits . 24
4.3.1.12.4 Conformance . 24
4.3.2 Technical requirements for other types of Wide Band modulation . 24
4.3.2.1 Introduction . 24
4.3.2.2 RF output power . 24
4.3.2.2.1 Applicability . 24
4.3.2.2.2 Definition. 25
4.3.2.2.3 Limit . 25
4.3.2.2.4 Conformance . 25
4.3.2.3 Power Spectral Density . 25
4.3.2.3.1 Applicability . 25
4.3.2.3.2 Definition. 25
4.3.2.3.3 Limit . 25
4.3.2.3.4 Conformance . 25
4.3.2.4 Duty Cycle, Tx-sequence, Tx-gap . 25
4.3.2.4.1 Applicability . 25
4.3.2.4.2 Definition. 25
4.3.2.4.3 Limit . 26
4.3.2.4.4 Conformance . 26
4.3.2.5 Medium Utilization (MU) factor . 26
4.3.2.5.1 Applicability . 26
4.3.2.5.2 Definition. 26
4.3.2.5.3 Limit . 26
4.3.2.5.4 Conformance . 26
4.3.2.6 Adaptivity (adaptive equipment using modulations other than FHSS) . 26
4.3.2.6.1 Applicability . 26
4.3.2.6.2 Non-LBT based Detect and Avoid . 27
4.3.2.6.3 LBT based Detect and Avoid . 27
4.3.2.6.4 Short Control Signalling Transmissions . 29
4.3.2.7 Occupied Channel Bandwidth . 30
4.3.2.7.1 Applicability . 30
4.3.2.7.2 Definition. 30
4.3.2.7.3 Limits . 30
4.3.2.7.4 Conformance . 30
4.3.2.8 Transmitter unwanted emissions in the out-of-band domain . 30
4.3.2.8.1 Applicability . 30
4.3.2.8.2 Definition. 30
4.3.2.8.3 Limit . 30
4.3.2.8.4 Conformance . 31
4.3.2.9 Transmitter unwanted emissions in the spurious domain . 31
4.3.2.9.1 Applicability . 31
4.3.2.9.2 Definition. 31
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 300 328 V1.8.2:2014
 5 Draft ETSI EN 300 328 V1.8.2 (2014-04)
4.3.2.9.3 Limit . 31
4.3.2.9.4 Conformance . 31
4.3.2.10 Receiver spurious emissions . 32
4.3.2.10.1 Applicability . 32
4.3.2.10.2 Definition. 32
4.3.2.10.3 Limit . 32
4.3.2.10.4 Conformance . 32
4.3.2.11 Receiver Blocking . 32
4.3.2.11.1 Applicability . 32
4.3.2.11.2 Definition. 32
4.3.2.11.3 Limits . 32
4.3.2.11.4 Conformance . 33
5 Essential radio test suites . 33
5.1 Conditions for testing . 33
5.1.1 Normal and extreme test conditions. 33
5.1.1.1 Introduction . 33
5.1.1.2 Normal test conditions . 33
5.1.1.2.1 Normal temperature and humidity . 33
5.1.1.2.2 Normal power source . 33
5.1.1.3 Extreme test conditions . 33
5.1.1.3.1 Extreme temperatures . 33
5.1.1.3.2 Extreme power source voltages . 33
5.1.2 Test mode. 34
5.1.3 Antennas and transmit operating modes . 34
5.1.3.1 Integrated and dedicated antennas . 34
5.1.3.2 Smart antenna systems and related operating modes . 34
5.1.3.2.1 Introduction . 34
5.1.3.2.2 Operating mode 1 (single antenna) . 34
5.1.3.2.3 Operating mode 2 (multiple antennas, no beamforming) . 35
5.1.3.2.4 Operating mode 3 (multiple antennas, with beamforming) . 35
5.1.3.3 Output power setting . 35
5.1.4 Adaptive and Non-adaptive equipment. 35
5.1.5 Presentation of equipment . 35
5.1.5.1 Testing of stand-alone equipment . 35
5.1.5.2 Testing of host connected equipment and plug-in radio equipment . 35
5.1.5.2.1 Introduction . 35
5.1.5.2.2 The use of a host or test jig for testing Plug-In radio equipment . 35
5.1.5.2.3 Testing of combinations . 36
5.1.6 Test Fixture . 36
5.2 Interpretation of the measurement results . 37
5.3 Test procedures for essential radio test suites. 37
5.3.1 Product Information . 37
5.3.2 RF output power, Duty Cycle, Tx-sequence, Tx-gap, Medium Utilization . 38
5.3.2.1 Test conditions . 38
5.3.2.2 Test method . 39
5.3.2.2.1 Conducted measurements . 39
5.3.2.2.2 Radiated measurements . 41
5.3.3 Power Spectral Density . 41
5.3.3.1 Test conditions .
...