ETSI TR 103 061-3 V1.2.1 (2014-04)

ETSI TR 103 061-3 V1.2.1 (2014-04)






Technical Report
Intelligent Transport Systems (ITS);
Testing;
Part 3: Conformance test specifications for Geographical
addressing and forwarding for point-to-point and
point-to-multipoint communications;
GeoNetworking validation report

---------------------- Page: 1 ----------------------
2 ETSI TR 103 061-3 V1.2.1 (2014-04)



Reference
RTR/ITS-00341
Keywords
ITS, OTE, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TR 103 061-3 V1.2.1 (2014-04)
Contents
Intellectual Property Rights . 4
Foreword . 4
Introduction . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.1 Informative references . 5
3 Abbreviations . 6
4 Validation report . 6
4.1 Validation level . 6
4.2 Source code evaluation . 6
4.2.1 TTCN-3 version . 6
4.2.2 TTCN-3 tools used for compilation . 7
4.3 Validation Process . 7
4.3.1 Test Platforms . 7
4.3.2 SUTs . 7
4.3.3 Validation Status . 8
4.4 Feedback to standardization process . 10
4.4.1 Base standard issues. 10
4.4.2 Test specification issues . 11
4.4.3 Typical SUT issues . 11
Annex A: Bibliography . 12
History . 14

ETSI

---------------------- Page: 3 ----------------------
4 ETSI TR 103 061-3 V1.2.1 (2014-04)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Report (TR) has been produced by ETSI Technical Committee Intelligent Transport Systems (ITS).
The present document is part 3 of a multi-part deliverable. Full details of the entire series can be found in part 1 [i.8].
Introduction
In response to EC mandate M/453 [i.9], ETSI Technical Committee ITS has standardized base and test specifications
for ITS protocols. In a next step a prototype TTCN-3 test system was built and validated. The present document and its
related TR 103 099 [i.5] (Architecture of Conformance Validation Framework), describe the validation and design of
the prototype TTCN-3 test system.
The action described in the present document has supported the implementation of ITS standards by:
• Making available validated and standardized test specifications and thus enabling the application of reliable
certification schemes.
• Executing conformance validation framework against real Implementations Under Test (IUTs) from industry
and thus providing these companies with a conformance assessment of their implementations. During the
lifetime of this action, the conformance validation framework was as well provided at ITS Cooperative
Mobility Services Interoperability events.
• Releasing all software as open source and thus allowing industry to build and run their own conformance
validation framework.
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TR 103 061-3 V1.2.1 (2014-04)
1 Scope
The present document is the validation report of the GeoNetworking conformance tests defined in TS 102 871-3 [i.2]
derived from EN 302 636-4-1 (V1.2.0) [i.1]. It provides statistics of executed and validated GeoNetworking
conformance tests. The information provided has been produced by validation against at least two prototype
implementations from industry.
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
Not applicable.
2.1 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 302 636-4-1 (V1.2.0): "Intelligent Transport Systems (ITS); Vehicular Communications;
GeoNetworking; Part 4: Geographical addressing and forwarding for point-to-point and point-to-
multipoint communications; Sub-part 1: Media-Independent Functionality".
[i.2] ETSI TS 102 871-3 (V1.1.1): "Intelligent Transport Systems (ITS); Testing; Conformance test
specifications for GeoNetworking ITS-G5; Part 3: Abstract Test Suite (ATS) and Protocol
Implementation eXtra Information for Testing (PIXIT)".
[i.3] ETSI TS 102 871-3 (V1.2.1): "Intelligent Transport Systems (ITS); Testing; Conformance test
specifications for GeoNetworking ITS-G5; Part 3: Abstract Test Suite (ATS) and Protocol
Implementation eXtra Information for Testing (PIXIT)".
[i.4] ETSI TS 102 871-2 (V1.1.1): "Intelligent Transport Systems (ITS); Testing; Conformance test
specifications for GeoNetworking ITS-G5; Part 2: Test Suite Structure and Test Purposes
(TSS&TP)".
[i.5] ETSI TR 103 099 (V1.2.1): "Intelligent Transport Systems (ITS); Architecture of conformance
validation framework".
[i.6] ETSI EG 201 015 (V1.1.1): "Methods for Testing and Specification (MTS); Specification of
protocols and services; Validation methodology for standards using SDL; Handbook".
[i.7] ETSI ES 201 873-1 (V4.5.1): "Methods for Testing and Specification (MTS); The Testing and
Test Control Notation version 3; Part 1: TTCN-3 Core Language".
[i.8] ETSI TR 103 061-1: "Intelligent Transport Systems (ITS); Testing; Part 1: Conformance test
specifications for Co-operative Awareness Messages (CAM); CAM validation report".
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TR 103 061-3 V1.2.1 (2014-04)
[i.9] EC mandate M/453: "Standardisation mandate addressed to CEN, CENELEC and ETSI in the
field of Information and Communication Technologies to support the interoperability of
co-operative Systems for Intelligent Transport in the European Community".
3 Abbreviations
For the purposes of the present document, the following abbreviations apply:
ASN.1 Abstract Syntax Notation One
ATS Abstract Test Suite
CAM Co-operative Awareness Message
CBF Contention Based Forwarding
DENM Decentralized Environmental Notification Messages basic service
DEPV Destination Position Vector
EC European Commission
GAC Geographically-scoped AnyCast
GN GeoNetworking
ITS Intelligent Transportat Systems
IUT Implementation Under Test
LS Location Service
PICS Protocol Implementation Conformance Statement
SCF Store Carry & Forward
SHB Single Hop Broadcast
SO SOurce
SOPV SOurce Position Vector
SQN SeQuence Number
SUT System Under Test
TC Test Cases
TP Test Purposes
TSB Topology Scoped Broadcast
TTCN-3 Testing and Test Control Notation 3
UC UniCast
UT Upper Tester
4 Validation report
4.1 Validation level
Level 3 (Rigorous) abstract test suite validation has been performed, according to the validation handbook
EG 201 015 [i.6]:
• the test suite has been compiled on more than one TTCN-3 tool;
• the complete suite of tests has been implemented and executed on more than
...