ETSI EN 301 908-5 V5.2.1 (2011-09)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.YHQFDPLFGPDIMT cellular networks - Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive - Part 5: CDMA Multi-Carrier (cdma2000) Base Stations (BS)33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 301 908-5 Version 5.2.1SIST EN 301 908-5 V5.2.1:2011en01-november-2011SIST EN 301 908-5 V5.2.1:2011SLOVENSKI
STANDARD



SIST EN 301 908-5 V5.2.1:2011



ETSI EN 301 908-5 V5.2.1 (2011-09) IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 5: CDMA Multi-Carrier (cdma2000) Base Stations (BS)
Harmonized European Standard SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 2
Reference REN/MSG-TFES-007-5 Keywords 3G, 3GPP2, cdma2000, cellular, digital, IMT-2000, mobile, radio, regulation, UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 3 Contents Intellectual Property Rights . 6 Foreword . 6 Introduction . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 9 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 10 3.1 Definitions . 10 3.2 Symbols . 19 3.3 Abbreviations . 22 4 Technical requirements specifications . 23 4.1 Environmental profile . 23 4.2 Conformance requirements . 23 4.2.1 Introduction. 23 4.2.2 Transmitter conducted spurious emissions . 24 4.2.2.1 Definition . 24 4.2.2.2 Limits . 24 4.2.2.2.1 Macro cell base station . 24 4.2.2.2.2 Pico cell base station and femto cell . 26 4.2.2.3 Conformance . 28 4.2.3 Maximum output power . 28 4.2.3.1 Definition . 28 4.2.3.2 Limits . 28 4.2.3.2.1 Base stations operating in Type 1 cdma2000 systems . 28 4.2.3.2.2 Base stations operating in Type 2 cdma2000 systems . 28 4.2.3.3 Conformance . 29 4.2.4 Inter-Base Station transmitter intermodulation . 29 4.2.4.1 Definition . 29 4.2.4.2 Limits . 29 4.2.4.3 Conformance . 29 4.2.5 Receiver conducted spurious emissions . 30 4.2.5.1 Definition . 30 4.2.5.2 Limits . 30 4.2.5.3 Conformance . 30 4.2.6 Receiver blocking characteristics . 30 4.2.6.1 Definition . 30 4.2.6.2 Limits . 30 4.2.6.2.1 Base stations operating in Type 1 cdma2000 systems . 30 4.2.6.2.2 Base stations operating in Type 2 cdma2000 systems . 30 4.2.6.3 Conformance . 30 4.2.7 Intermodulation spurious response attenuation . 31 4.2.7.1 Definition . 31 4.2.7.2 Limits . 31 4.2.7.2.1 Base stations operating in Type 1 cdma2000 systems . 31 4.2.7.2.2 Base stations operating in Type 2 cdma2000 systems . 31 4.2.7.3 Conformance . 31 4.2.8 Adjacent channel selectivity . 31 4.2.8.1 Definition . 31 4.2.8.2 Limits . 31 4.2.8.2.1 Base stations operating in Type 1 cdma2000 systems . 31 4.2.8.2.2 Base stations operating in Type 2 cdma2000 systems . 31 4.2.8.3 Conformance . 31 SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 4 5 Testing for compliance with technical requirements . 32 5.1 Conditions for testing . 32 5.1.1 Introduction. 32 5.1.2 Standard equipment under test . 32 5.1.2.1 Basic equipment . 32 5.1.2.2 Ancillary equipment . 32 5.2 Interpretation of the measurement results . 32 5.3 Essential radio test suites . 32 5.3.1 Transmitter conducted spurious emissions . 33 5.3.1.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 33 5.3.1.1.1 Macro cell base station . 33 5.3.1.1.2 Pico cell base station and femto cell . 33 5.3.1.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 35 5.3.1.2.1 Macro cell base station . 35 5.3.1.2.2 Pico cell base station and femto cell . 36 5.3.2 Maximum output power . 38 5.3.2.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 38 5.3.2.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 39 5.3.3 Inter-Base Station transmitter intermodulation . 39 5.3.3.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 39 5.3.3.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems 2 . 39 5.3.4 Receiver conducted spurious emissions . 40 5.3.4.1 Test procedure for Base Stations supporting operation in Type 1 or Type 2 cdma2000 systems . 40 5.3.5 Receiver blocking characteristics . 41 5.3.5.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 41 5.3.5.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 42 5.3.6 Intermodulation spurious response attenuation . 42 5.3.6.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 42 5.3.6.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 44 5.3.7 Adjacent channel selectivity . 44 5.3.7.1 Test procedure for Base Stations supporting operation in Type 1 cdma2000 systems . 44 5.3.7.2 Test procedure for Base Stations supporting operation in Type 2 cdma2000 systems . 45 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 46 Annex B (normative): Base station Configurations . 48 B.1 Receiver diversity . 48 B.2 Duplexers . 48 B.3 Power supply options . 48 B.4 Ancillary RF amplifiers . 49 B.5 BS using antenna arrays . 49 B.5.1 Receiver tests . 50 B.5.2 Transmitter tests . 50 Annex C (informative): Environmental profile and standard test conditions . 51 C.1 Introduction . 51 C.2 CDMA environmental requirements . 51 C.2.1 Temperature and power supply voltage . 51 C.2.1.1 Definition . 51 C.2.1.2 Method of measurement . 51 C.2.1.3 Minimum standard . 52 C.2.2 High humidity . 52 C.2.2.1 Definition . 52 C.2.2.2 Method of measurement . 52 C.2.2.3 Minimum standard . 52 C.3 Standard test conditions. 52 SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 5 C.3.1 Standard environmental test conditions . 52 C.3.2 Standard conditions for the primary power supply . 53 C.3.2.1 General . 53 C.3.2.2 Standard DC test voltage from accumulator batteries . 53 C.3.2.3 Standard AC voltage and frequency . 53 Annex D (informative): The EN title in the official languages . 54 Annex E (informative): Bibliography . 55 History . 56
SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been produced by ETSI in response to mandate M/284 from the European Commission issued under Council Directive 98/34/EC [i.1] (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.2]. See article 5.1 of Directive 1999/5/EC [i.2] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.2] are summarised in annex A. The present document is part 5 of a multi-part deliverable covering the essential requirements under article 3.2 of Directive 1999/5/EC [i.2] (R&TTE Directive) for Base Stations (BS), Repeaters and User Equipment (UE) for IMT cellular networks, as identified below: Part 1: "Introduction and common requirements"; Part 2: "CDMA Direct Spread (UTRA FDD) User Equipment (UE)"; Part 3: "CDMA Direct Spread (UTRA FDD) Base Stations (BS)"; Part 4: "CDMA Multi-Carrier (cdma2000) User Equipment (UE)"; Part 5: "CDMA Multi-Carrier (cdma2000) Base Stations (BS)"; Part 6: "CDMA TDD (UTRA TDD) User Equipment (UE)"; Part 7: "CDMA TDD (UTRA TDD) Base Stations (BS)"; Part 8: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (UE) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 9: "Harmonized EN for IMT-2000, TDMA Single-Carrier (UWC 136) (BS) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 10: "Harmonized EN for IMT-2000, FDMA/TDMA (DECT) covering essential requirements of article 3.2 of the R&TTE Directive"; Part 11: "CDMA Direct Spread (UTRA FDD) (Repeaters)"; Part 12: "Harmonized EN for IMT-2000, CDMA Multi-Carrier (cdma2000) (Repeaters) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 13: "Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)"; SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 7 Part 14: "Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)"; Part 15: "Evolved Universal Terrestrial Radio Access (E-UTRA) (FDD Repeaters)"; Part 16: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (UE) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 17: "Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive"; Part 18:
"E-UTRA, UTRA and GSM/EDGE Multi-Standard Radio (MSR) Base Stations (BS)"; Part 19: "OFDMA TDD WMAN (Mobile WiMAX) TDD User Equipment (UE)"; Part 20:
"OFDMA TDD WMAN (Mobile WiMAX) TDD Base Station (BS)"; Part 21:
"OFDMA TDD WMAN (Mobile WiMAX) FDD User Equipment (UE)"; Part 22:
"OFDMA TDD WMAN (Mobile WiMAX) FDD Base Stations (BS)".
National transposition dates Date of adoption of this EN: 12 September 2011 Date of latest announcement of this EN (doa): 31 December 2011 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
30 June 2012 Date of withdrawal of any conflicting National Standard (dow): 30 June 2013
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.2]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 8 1 Scope The present document applies to the following radio equipment types: • Base stations for IMT-2000 CDMA multi-carrier (cdma2000) and Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB). These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: CDMA multi-carrier Base Station operating bands Band Class (BC) Direction of transmission CDMA multi-carrier Base Station operating bands 6 Transmit 2 110 MHz to 2 170 MHz Receive 1 920 MHz to 1 980 MHz 8 Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz 9 Transmit 925 MHz to 960 MHz Receive 880 MHz to 915 MHz 13 Transmit 2 620 MHz to 2 690 MHz Receive 2 500 MHz to 2 570 MHz
The present document covers requirements for IMT-2000 CDMA multi-carrier (cdma2000) User Equipments and Evolved CDMA Multi-Carrier (UMB) User Equipment. Base stations for IMT-2000 CDMA multi-carrier (cdma2000) may support: 1) operation in cdma2000 spread spectrum systems as defined in 3GPP2 C.S0002-E [2], referred to herein as operation in Type 1 cdma2000 systems; or 2) operation in cdma2000 High Rate Packet Data Systems as defined in 3GPP2 C.S0024-C [7] subtypes 0, 1, 2 and 3, referred to herein in Type 2 cdma2000 systems. The present document is intended to cover the provisions of Directive 1999/5/EC [i.2] (R&TTE Directive) article 3.2, which states that "[…] radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radio communications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.2] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org/. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. SIST EN 301 908-5 V5.2.1:2011



ETSI ETSI EN 301 908-5 V5.2.1 (2011-09) 9 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] 3GPP2 C.S0010-D V1.0 (September 2010): "Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Base Stations". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0010-D_v1.0_MPS_for_cdma2000_1x_BS.pdf. [2] 3GPP2 C.S0002-E V2.0 (June 2010): "Physical Layer Standard for cdma2000 Spread Spectrum Systems Revision E". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0002-E_v2.0_cdma2000_1x_PHY.pdf. [3] ANSI/TIA-98-F-1 (June 2006): "Recommended Minimum Performance Standards for cdma2000 Spread Spectrum Mobile Stations - Addendum". [4] TIA/EIA-126-D (June 2001): "Loopback Service Options Standard (LSO) for cdma Spread Spectrum Systems". [5] TIA-870-A (March 2005): "Test Data Service Option (TDSO) for cdma2000 Spread Spectrum Systems - Revision A". [6] TIA-871-1 (October 2009): "Markov Service Option for cdma2000 Spread Spectrum Systems". [7] 3GPP2 C.S0024-200-C V1.0 (April 2010): "Physical Layer for cdma2000 High Rate Packet Data Air Interface Specification". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0024-200-C_v1.0_HRPD_PHY.pdf. [8] 3GPP2 C.S0032-C V1.0 (September 2010): "Recommended Minimum Performance Standards for cdma2000 High Rate Packet Data Access Network". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0032-C_v1.0_MPS_for_HRPD_AN.pdf. [9] 3GPP2 C.S0029-B V1.0 (March 2008): "Test Application Specification (TAS) for High Rate Packet Data Air Interface". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/C.S0029-B_v1.0_080409.pdf. [10] ETSI EN 301 908-1 (V5.2.1): "IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive; Part 1: Introduction and common requirements". [11] ETSI EN 301 908-17 (V4.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 17: Harmonized EN for IMT-2000, Evolved CDMA Multi-Carrier Ultra Mobile Broadband (UMB) (BS) covering the essential requirements of article 3.2 of the R&TTE Directive". [12] 3GPP2 X.S0059-100-0 V1.0 (January 2010): "Femto Network Specification". NOTE: Available at: http://www.3gpp2.org/Public_html/specs/X.S0059
...