ETSI EN 301 068-3 V1.2.1 (2002-08)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; Connection characteristics; ATM transfer capability and traffic parameter indication; Part 3: Test Suite Structure and Test Purposes (TSS&TP) specification for the user33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)ICS:Ta slovenski standard je istoveten z:EN 301 068-3 Version 1.2.1SIST EN 301 068-3 V1.2.1:2003en01-november-2003SIST EN 301 068-3 V1.2.1:2003SLOVENSKI
STANDARD



SIST EN 301 068-3 V1.2.1:2003



ETSI EN 301 068-3 V1.2.1 (2002-08)European Standard (Telecommunications series) Broadband Integrated Services Digital Network (B-ISDN);Digital Subscriber Signalling System No. two (DSS2) protocol;Connection characteristics;ATM transfer capability and traffic parameter indication;Part 3: Test Suite Structure and Test Purposes (TSS&TP)specification for the user
SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 2
Reference REN/SPAN-130275-3 Keywords ATM, B-ISDN, DDS2, layer 3, TSS&TP, UNI, user ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2002. All rights reserved.
DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 3
Contents Intellectual Property Rights.4 Foreword.4 1 Scope.5 2 References.5 3 Definitions, symbols and abbreviations.6 3.1 Definitions.6 3.1.1 Definitions related to conformance testing.6 3.1.2 Definitions related to EN 301 068-1.6 3.2 Symbols.7 3.3 Abbreviations.7 4 Test Suite Structure (TSS).8 5 Test Purposes (TP).8 5.1 Introduction.8 5.1.1 TP naming convention.8 5.1.2 Source of TP definition.8 5.1.3 Test strategy.9 5.1.4 Test of call states.9 5.1.5 Validity of Test Purposes.9 5.2 TPs for the ATM transfer capability and traffic parameter indication, user.9 5.2.1 Signalling procedures at the coincident SB/TB and at the TB reference points.9 5.2.1.1 Additional parameter procedures at the originating interface.9 5.2.1.1.1 Sustainable Cell Rate parameter set (01).9 5.2.1.1.2 Traffic management option for support of tagging (02).10 5.2.1.1.3 Broadband Bearer Capability (03).11 5.2.1.1.4 Available Bit Rate set-up parameter (04).11 5.2.1.1.5 ATM Block Transfer capability (05).12 5.2.1.1.6 SBR ATM transfer capability (06).12 5.2.1.1.7 Handling of error conditions (07).12 5.2.1.2 Additional parameter procedures at the destination interface.13 5.2.1.2.1 Sustainable Cell Rate parameter set (08).13 5.2.1.2.2 Traffic management option for support of tagging (09).14 5.2.1.2.3 Broadband Bearer Capability (10).14 5.2.1.2.4 Available Bit Rate set-up parameter (11).15 5.2.1.2.5 ATM Block Transfer capability (12).15 5.2.1.2.6 SBR ATM transfer capability (13).16 5.2.1.2.7 Handling of error conditions (14).16 6 Compliance.17 7 Requirements for a comprehensive testing service.18 Annex A (informative): Bibliography.19 History.20
SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 4
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services and Protocols for Advanced Networks (SPAN). The present document is part 3 of a multi-part deliverable covering the Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; Connection characteristics; ATM transfer capability and traffic parameter indication, as identified below: Part 1: "Protocol specification [ITU-T Recommendations Q.2961.1 (1995), Q.2961.2 (1997), Q.2961.3 (1997), Q.2961.4 (1997), Q.2961.6 (1998), modified]"; Part 2: "Protocol Implementation Conformance Statement (PICS) proforma specification"; Part 3: "Test Suite Structure and Test Purposes (TSS&TP) specification for the user"; Part 4: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification for the user"; Part 5: "Test Suite and Test Purposes (TSS&TP) specification for the network"; Part 6: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification for the network".
National transposition dates Date of adoption of this EN: 2 August 2002 Date of latest announcement of this EN (doa): 30 November 2002 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 May 2003 Date of withdrawal of any conflicting National Standard (dow): 31 May 2003
SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 5
1 Scope The present document specifies the user Test Suite Structure and Test Purposes (TSS&TP) for the TB reference point or coincident SB and TB reference point (as defined in ITU-T Recommendation I.413 [5]) of implementations conforming to the standards for the signalling user-network layer 3 specification for ATM transfer capability and traffic parameter indication of the Digital Subscriber Signalling System No. two (DSS2) protocol for the pan-European Broadband Integrated Services Digital Network (B-ISDN), EN 301 068-1 [1]. A further part of the present document specifies the Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma based on the present document. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. [1] ETSI EN 301 068-1: "Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; Connection characteristics; ATM transfer capability and traffic parameter indication; Part 1: Protocol specification [ITU-T Recommendations Q.2961.1 (1995), Q.2961.2 (1997), Q.2961.3 (1997), Q.2961.4 (1997) and Q.2961.6 (1997), modified]". [2] ETSI EN 301 068-2: "Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; Connection characteristics; ATM transfer capability and traffic parameter indication; Part 2: Protocol Implementation Conformance Statement (PICS) proforma specification". [3] ISO/IEC 9646-1 (1994): "Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 1: General concepts". [4] ISO/IEC 9646-2 (1994): "Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 2: Abstract Test Suite specification". [5] ITU-T Recommendation I.413 (1993): "B-ISDN user-network interface". [6] ETSI ETS 300 406: "Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology". [7] ETSI EN 300 443-1: "Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; B-ISDN user-network interface layer 3 specification for basic call/bearer control; Part 1: Protocol specification [ITU-T Recommendation Q.2931 (1995), modified]". [8] ETSI EN 301 067-1: "Broadband Integrated Services Digital Network (B-ISDN); Digital Subscriber Signalling System No. two (DSS2) protocol; Connection characteristics; Negotiation during call/connection establishment phase; Part 1: Protocol specification [ITU-T Recommendation Q.2962 (1996), modified]". [9] ITU-T Recommendation Q.2961: "Digital subscriber signalling system No. 2 (DSS 2)- Additional traffic parameters". [10] ITU-T Recommendation Q.2961.1: "Additional signalling capabilities to support traffic parameters for the tagging option and the sustainable cell rate parameter set". SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 6
[11] ITU-T Recommendation Q.2961.2: "Support of ATM transfer capability in the broadband bearer capability information element". [12] ITU-T Recommendation Q.2961.3: "Signalling capabilities to support traffic parameters for the available bit rate (ABR) ATM transfer capability". [13] ITU-T Recommendation Q.2961.4: "Signalling capabilities to support traffic parameters for the ATM Block Transfer (ABT) ATM transfer capability". [14] ITU-T Recommendation Q.2961.6: "Additional signalling procedures for the support of the SBR2 and SBR3 ATM transfer capabilities". 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in EN 301 068-1 [1], EN 300 443-1 [7] and the following apply: 3.1.1 Definitions related to conformance testing abstract test case: See ISO/IEC 9646-1 [3]. Abstract Test Method (ATM): See ISO/IEC 9646-1 [3]. Abstract Test Suite (ATS): See ISO/IEC 9646-1 [3]. Implementation Under Test (IUT): See ISO/IEC 9646-1 [3]. lower tester: See ISO/IEC 9646-1 [3]. Protocol Implementation Conformance Statement (PICS): See ISO/IEC 9646-1 [3]. PICS proforma: See ISO/IEC 9646-1 [3]. Protocol Implementation eXtra Information for Testing (PIXIT): See ISO/IEC 9646-1 [3]. PIXIT proforma: See ISO/IEC 9646-1 [3]. Test Purpose (TP): See ISO/IEC 9646-1 [3]. 3.1.2 Definitions related to EN 301 068-1 user: DSS2 protocol entity at the User side of the user-network interface where a TB reference point or coincident SB and TB reference point applies user (SB/TB): DSS2 protocol entity at the User side of the user-network interface where a coincident SB and TB reference point applies user (TB): DSS2 protocol entity at the User side of the user-network interface where a TB reference point applies (user is a private ISDN) SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 7
3.2 Symbols For the purposes of the present document, the following symbols apply: SB Interface Reference Point at S (broadband) TB Interface Reference Point at T (broadband) U0 Null call/connection state U1 Call Initiated call/connection state U3 Outgoing Call Proceeding call/connection state U4 Call Delivered call/connection state U7 Call Received call/connection state U8 Connect Request call/connection state U9 Incoming Call Proceeding call/connection state U10 Active call/connection state 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: ABR Available Bit Rate ABT-DT ATM Block Transfer with Delayed Transmission ABT-IT ATM Block Transfer with Immediate Transmission ATM Abstract Test Method ATS Abstract Test Suite B-ISDN Broadband Integrated Services Digital Network
CLP Cell Loss Priority DSS2 Digital Subscriber Signalling System No. two ICR Initial Cell Rate ISDN Integrated Services Digital Network IUT Implementation Under Test PCR Peak Cell Rate PICS Protocol Implementation Conformance Statement PIXIT Protocol Implementation eXtra Information for Testing RDF Rate Decrease Factor RIF Rate Increase Factor RM Resource Management SBR Statistical Bit Rate ATC TBE ABR Transient Buffer Exposure TP Test Purpose TSS Test Suite Structure SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 8
4 Test Suite Structure (TSS) •
Signalling procedures at the coincident SB/TB and at the TB reference points - Additional parameter procedures at the originating interface.
Sustainable cell rate parameter set
(01)
Traffic management option for support of tagging (02)
Broadband bearer capability
(03)
Available bit rate setup parameter
(04)
ATM transfer block capability
(05)
SBR ATM transfer capability
(06)
Handling of error conditions
(07) - Additional parameter procedures at the destination interface.
Sustainable cell rate parameter set
(08)
Traffic management option for support of tagging (09)
Broadband bearer capability
(12)
SBR ATM transfer capability
(13)
Handling of error conditions
(14) 5 Test Purposes (TP) 5.1 Introduction For each test requirement a TP is defined. 5.1.1 TP naming convention TPs are numbered, starting at 01, within each group. Groups are organized according to the TSS. Additional references are added to identify the actual test suite (see table 1). Table 1: TP identifier naming convention scheme Identifier: __
= service + type of IUT: "INDU" for connection INDication, IUT = User
= group number:
two character field representing the group reference according to TSS
= sequential number:
(01-99)
5.1.2 Source of TP definition The TPs are based on EN 301 068-1 [1]. SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 9
5.1.3 Test strategy As the base standard EN 301 068-1 [1] contains no explicit requirements for testing, the TPs were generated as a result of an analysis of the base standard and the PICS specification EN 301 068-2 [2]. The TPs are only based on conformance requirements related to the externally observable behaviour of the IUT and are limited to conceivable situations to which a real implementation is likely to be faced (see ETS 300 406 [6]). 5.1.4 Test of call states Many TPs include a reference to the IUT's final call state after the realization of the TP. In these cases the TP includes the requirement to ensure that the IUT has entered this particular final call state. Ensuring that the IUT is in a particular call state shall be realized by following the procedures described in clause 5.6.11 of EN 300 443-1 [7]. According to these procedures, the IUT on receipt of a STATUS ENQUIRY message, shall respond with a STATUS message indicating, in the fifth octet of the Call state information element, the current call state of the IUT. This exchange of messages is not mentioned explicitly in each TP but is considered to be implicit in the reference to the final call state. This way of phrasing the TPs has been used to avoid over-complicating the text and structure of the TPs and to improve the readability. 5.1.5 Validity of Test Purposes The test purposes below are valid only for IUTs that do not use the negotiation procedure defined in EN 301 067-1 [8]. These procedures are tested in the test specification standards related to EN 301 067-1 [8]. 5.2 TPs for the ATM transfer capability and traffic parameter indication, user All PICS items referred to in this clause are as specified in EN 301 068-2 [2] unless indicated otherwise by another numbered reference. Unless specified: • the messages indicated are valid and contain at least the mandatory information elements and possibly optional information elements; • the information elements indicated are valid and contain at least the mandatory parameters and possibly optional parameters. 5.2.1 Signalling procedures at the coincident SB/TB and at the TB reference points NOTE: Unless otherwise specified, the connection defined by the requested ATM traffic descriptor is available for use. 5.2.1.1 Additional parameter procedures at the originating interface Test purposes for EN 301 068-1 [1]. 5.2.1.1.1 Sustainable Cell Rate parameter set (01) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.1 [10], modified). NOTE: In the following test purpose Sustainable cell rate parameter set includes Sustainable cell rate and Maximum Burst size. SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 10 INDU_01_01 Ensure that the IUT in U0, in order to initiate a call with additional traffic parameter selection, sends a SETUP message with the ATM traffic descriptor information element (including sustainable cell rate parameter set without traffic options management identifier field) and enters U1. INDU_01_02 Ensure that the IUT in U3 (having sent a SETUP message with the ATM traffic descriptor information element including sustainable cell rate parameter set without traffic options management identifier field), on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_01_03 Ensure that the IUT in U4 (having sent a SETUP message with the ATM traffic descriptor information element including sustainable cell rate parameter set without traffic options management identifier field), on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. 5.2.1.1.2 Traffic management option for support of tagging (02) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.1 [10], modified). INDU_02_01 Ensure that the IUT in U0, in order to initiate a call indicating the support of the local tagging option, sends a SETUP message with the ATM traffic descriptor information element (including the traffic management option field with the Tf value set to "tagging requested") and enters U1". INDU_02_02 Ensure that the IUT in U0, in order to initiate a call indicating the non-support of the local tagging option, sends a SETUP message with the ATM traffic descriptor information element (including the traffic management option field with the Tf value set to "tagging not allowed") and enters U1. INDU_02_03 Ensure that the IUT in U3 (having sent a SETUP message with the ATM traffic descriptor information element requesting local tagging including tagging information), on receipt of a CONNECT message including a compatible ATM traffic descriptor information element (with Tf subfield of traffic management option indicating "tagging applied"), sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_04 Ensure that the IUT in U3 (having sent a SETUP message with the ATM traffic descriptor information element requesting local tagging including tagging information), on receipt of a CONNECT message including a compatible ATM traffic descriptor information element (with Tf subfield of traffic management option indicating "tagging not applied"), sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_05 Ensure that the IUT in U3 (having sent a SETUP message with the ATM traffic descriptor information element requesting local tagging including tagging information) on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_06 Ensure that the IUT in U4 (having sent a SETUP message with the ATM traffic descriptor information element, requesting local tagging) on receipt of a CONNECT message including a compatible ATM traffic descriptor information element (with Tf subfield of traffic management option indicating "tagging applied"), sends a CONNECT ACKNOWLEDGE message and enters U10. SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 11 INDU_02_07 Ensure that the IUT in U4 (having sent a SETUP message with the ATM traffic descriptor information element requesting local tagging including tagging information), on receipt of a CONNECT message including a compatible ATM traffic descriptor information element (with Tf subfield of traffic management option indicating "tagging not applied"), sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_08 Ensure that the IUT in U4 (having sent a SETUP message with the ATM traffic descriptor information element requesting local tagging including tagging information), on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_09 Ensure that the IUT in U3 (having sent a SETUP message with the ATM traffic descriptor information element not allowing local tagging) on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_02_10 Ensure that the IUT in U4 (having sent a SETUP message with the ATM traffic descriptor information element not allowing local tagging) on receipt of a CONNECT message without ATM traffic descriptor information element, sends a CONNECT ACKNOWLEDGE message and enters U10. 5.2.1.1.3 Broadband Bearer Capability (03) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.2 [11], modified). INDU_03_01 Ensure that the IUT in U0, in order to initiate a call including ATM transfer capability information, sends a SETUP message with a valid Broadband bearer capability information element (broadband transfer capability field present) and enters U1. 5.2.1.1.4 Available Bit Rate set-up parameter (04) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.3 [12], modified). INDU_04_01 Ensure that the IUT in U0, in order to initiate a call with ABR transfer capability, sends a SETUP message with a corresponding Broadband bearer capability information element ("ABR", "point-to-point") and with a valid ABR set-up parameter information element and enters U1. INDU_04_02 Ensure that the IUT in U3, (having sent a SETUP message requesting ABR transfer capability), on receipt of a compatible CONNECT message (including ABR set-up parameter information element, ATM traffic descriptor information element) sends a CONNECT ACKNOWLEDGE message and enters U10. INDU_04_03 Ensure that the IUT in U4, (having sent a SETUP message requesting ABR transfer capability), on receipt of a compatible CONNECT message (including ABR set-up parameter information element, ATM traffic descriptor information element) sends a CONNECT ACKNOWLEDGE message and enters U10. SIST EN 301 068-3 V1.2.1:2003



ETSI ETSI EN 301 068-3 V1.2.1 (2002-08) 12 5.2.1.1.5 ATM Block Transfer capability (05) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.4 [13], modified). INDU_05_01 Ensure that the IUT in U0, in order to initiate a call with ABT-IT transfer capability, sends a SETUP message with a corresponding Broadband bearer capability information element ("ABT-IT", "point-to-point") and with a valid ATM traffic descriptor (including forward and backward RM PCR parameters) and enters U1. INDU_05_02 Ensure that the IUT in U0, in order to initiate a call with ABT-DT transfer capability, sends a SETUP message with a corresponding Broadband bearer capability information element ("ABT-DT", "point-to-point") and with a valid ATM traffic descriptor (including forward and backward RM PCR parameters) and enters U1. INDU_05_03 Ensure that the IUT in U0, in order to initiate a call with ABT-IT transfer capability with negotiation allowed, sends a SETUP message with a corresponding Broadband bearer capability information element ("ABT-IT", "point-to-point") and with a valid ATM traffic descriptor (including forward and backward RM PCR parameters), and a valid corresponding Minimum acceptable ATM traffic descriptor and enters U1. INDU_05_04 Ensure that the IUT in U0, in order to initiate a call with ABT-DT transfer capability with negotiation allowed, sends a SETUP message with a corresponding Broadband bearer capability information element ("ABT-DT", "point-to-point") and with a valid ATM traffic descriptor (including forward and backward RM PCR parameters), and a valid corresponding Minimum acceptable ATM traffic descriptor and enters U1. 5.2.1.1.6 SBR ATM transfer capability (06) Test purposes for EN 301 068-1 [1] (ITU-T Recommendation Q.2961.6 [14], modified). INDU_06_01 Ensure that the IUT in U0, in order to initiate a cal
...