ETSI EN 300 113-2 V1.5.1 (2011-11)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Electromagnetic compatibility and Radio spectrum Matters (ERM) - Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector - Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive33.100.01Elektromagnetna združljivost na splošnoElectromagnetic compatibility in general33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:EN 300 113-2 Version 1.5.1SIST EN 300 113-2 V1.5.1:2012en01-februar-2012SIST EN 300 113-2 V1.5.1:2012SLOVENSKI
STANDARD



SIST EN 300 113-2 V1.5.1:2012



ETSI EN 300 113-2 V1.5.1 (2011-11) Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
Harmonized European Standard SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 2
Reference REN/ERM-TGDMR-296-2 Keywords antenna, data, mobile, PMR, radio, regulation, speech, TDD, TDMA ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http://portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2011. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 3 Contents Intellectual Property Rights . 5 Foreword . 5 Introduction . 5 1 Scope . 6 2 References . 6 2.1 Normative references . 7 2.2 Informative references . 7 3 Definitions, symbols and abbreviations . 7 3.1 Definitions . 7 3.2 Symbols . 7 3.3 Abbreviations . 7 4 Technical requirements specifications . 8 4.1 Environmental profile . 8 4.2 Transmitter requirements . 8 4.2.1 Frequency error . 8 4.2.1.1 Definition . 8 4.2.1.2 Limit . 8 4.2.1.3 Conformance . 8 4.2.2 Transmitter power (conducted) . 8 4.2.2.1 Definition . 8 4.2.2.2 Limit . 8 4.2.2.3 Conformance . 8 4.2.3 Maximum effective radiated power . 8 4.2.3.1 Definition . 8 4.2.3.2 Limit . 8 4.2.3.3 Conformance . 8 4.2.4 Adjacent and alternate channel power . 9 4.2.4.1 Definition . 9 4.2.4.2 Limit . 9 4.2.4.3 Conformance . 9 4.2.5 Unwanted emissions in the spurious domain . 9 4.2.5.1 Definition . 9 4.2.5.2 Limit . 9 4.2.5.3 Conformance . 9 4.2.6 Intermodulation attenuation . 9 4.2.6.1 Definition . 9 4.2.6.2 Limit . 9 4.2.6.3 Conformance . 9 4.2.7 Transient frequency behaviour of the transmitter . 9 4.2.7.1 Definition . 9 4.2.7.2 Limit . 9 4.2.7.3 Conformance . 9 4.2.8 Transmitter timeout timer . 10 4.2.8.1 Definition . 10 4.2.8.2 Limit . 10 4.2.8.3 Conformance . 10 4.3 Receiver requirements . 10 4.3.1 Maximum usable receiver sensitivity . 10 4.3.1.1 Definition . 10 4.3.1.2 Limit . 10 4.3.1.3 Conformance . 10 4.3.2 Co-channel rejection . 10 4.3.2.1 Definition . 10 4.3.2.2 Limit . 10 SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 4 4.3.2.3 Conformance . 10 4.3.3 Adjacent channel selectivity . 11 4.3.3.1 Definition . 11 4.3.3.2 Limit . 11 4.3.3.3 Conformance . 11 4.3.4 Spurious response rejection . 11 4.3.4.1 Definition . 11 4.3.4.2 Limit . 11 4.3.4.3 Conformance . 11 4.3.5 Intermodulation response rejection . 11 4.3.5.1 Definition . 11 4.3.5.2 Limit . 11 4.3.5.3 Conformance . 11 4.3.6 Blocking or desensitization . 11 4.3.6.1 Definition . 11 4.3.6.2 Limit . 12 4.3.6.3 Conformance . 12 4.3.7 Spurious radiations . 12 4.3.7.1 Definition . 12 4.3.7.2 Limit . 12 4.3.7.3 Conformance . 12 5 Testing for compliance with technical requirements . 12 5.1 Environmental conditions for testing . 12 5.1.1 Normal and extreme test-conditions . 12 5.1.2 Test power source . 12 5.1.3 Choice of samples for test suites . 12 5.2 Interpretation of the measurement results . 12 5.3 Essential radio test suites . 13 5.3.1 Frequency error . 13 5.3.2 Transmitter power (conducted) . 13 5.3.3 Maximum effective radiated power . 13 5.3.4 Adjacent and alternate channel power . 13 5.3.5 Unwanted emissions in the spurious domain . 13 5.3.6 Intermodulation attenuation . 13 5.3.7 Transient frequency behaviour of the transmitter . 13 5.3.8 Receiver Spurious radiations . 13 5.4 Other radio test suites . 13 5.4.1 Maximum usable receiver sensitivity . 14 5.4.2 Co-channel rejection . 14 5.4.3 Adjacent channel selectivity . 14 5.4.4 Spurious response rejection . 14 5.4.5 Intermodulation response rejection . 14 5.4.6 Receiver blocking or desensitization . 14 Annex A (normative): HS Requirements and conformance Test specifications Table (HS-RTT) . 15 Annex B (informative): The EN title in the official languages . 17 Annex C (informative): Bibliography . 18 History . 19
SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://ipr.etsi.org). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonized European Standard (EN) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Directive 98/34/EC [i.2] as amended by Directive 98/48/EC [i.5]. The title and reference to the present document are intended to be included in the publication in the Official Journal of the European Union of titles and references of Harmonized Standard under the Directive 1999/5/EC [i.1]. See article 5.1 of Directive 1999/5/EC [i.1] for information on presumption of conformity and Harmonised Standards or parts thereof the references of which have been published in the Official Journal of the European Union. The requirements relevant to Directive 1999/5/EC [i.1] are summarised in annex A. The present document is part 2 of a multi-part deliverable covering the Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector, as identified below: Part 1: "Technical characteristics and methods of measurement"; Part 2: "Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive".
National transposition dates Date of adoption of this EN: 21 November 2011 Date of latest announcement of this EN (doa): 29 February 2012 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 August 2012 Date of withdrawal of any conflicting National Standard (dow): 31 August 2013
Introduction The present document is part of a set of standards developed by ETSI and is designed to fit in a modular structure to cover all radio and telecommunications terminal equipment within the scope of the R&TTE Directive [i.1]. The modular structure is shown in EG 201 399 [i.3]. SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 6 1 Scope The present document covers the technical requirements for radio transmitters and receivers used in stations in the Private Mobile Radio (PMR) service. It applies to use in the land mobile service, operating on radio frequencies in all or in any part of the frequencies as given below, with channel separations of 12,5 kHz, 20 kHz and 25 kHz, intended for speech and/or data. Table 1: Radiocommunications service frequency bands
Radiocommunications service frequency bands Transmit
30 MHz to 1 000 MHz Receive
30 MHz to 1 000 MHz
It applies to equipment for continuous and/or discontinuous transmission of data and/or digital speech.
The equipment comprises a transmitter and associated encoder and modulator and/or a receiver and associated demodulator and decoder. The types of equipment covered by the present document are as follows: • base station (equipment fitted with an antenna connector, intended for use in a fixed location); • mobile station (equipment fitted with an antenna connector, normally used in a vehicle or as a transportable); and • those hand portable stations: a) fitted with an antenna socket; or b) without an external antenna socket, but fitted with a permanent internal or a temporary internal 50 Ω Radio Frequency (RF) connector which allows access to the transmitter output and the receiver input. Hand portable equipment without an external or internal RF connector and without the possibility of having a temporary internal 50 Ω RF connector is not covered by the present document. The present document is intended to cover the provisions of article 3.2 of Directive 1999/5/EC [i.1] (R&TTE Directive), which states that "(.) radio equipment shall be so constructed that it effectively uses the spectrum allocated to terrestrial/space radiocommunications and orbital resources so as to avoid harmful interference". In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of the R&TTE Directive [i.1] may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http://www.newapproach.org. 2 References References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the reference document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 7 2.1 Normative references The following referenced documents are necessary for the application of the present document. [1] ETSI EN 300 113-1 (V1.7.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Land mobile service; Radio equipment intended for the transmission of data (and/or speech) using constant or non-constant envelope modulation and having an antenna connector; Part 1: Technical characteristics and methods of measurement". 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. [i.1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (R&TTE Directive). [i.2] Directive 98/34/EC of the European Parliament and of the Council of 22 June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations and of rules on information society services. [i.3] ETSI EG 201 399 (V2.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM); A guide to the production of Harmonized Standards for application under the R&TTE Directive". [i.4] ETSI TR 100 028 (V1.4.1) (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics". [i.5] Directive 98/48/EC of the European Parliament and of the Council of 20 July 1998 amending Directive 98/34/EC laying down a procedure for the provision of information in the field of technical standards and regulations. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R&TTE Directive [i.1] and EN 300 113-1 [1] apply. 3.2 Symbols For the purposes of the present document, the symbols given in EN 300 113-1 [1] apply. 3.3 Abbreviations For the purposes of the present document, the abbreviations given in EN 300 113-1 [1] apply. SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 8 4 Technical requirements specifications 4.1 Environmental profile The technical requirements of the present document apply under the environmental profile for operation of the equipment, which shall be declared by the manufacturer of the equipment. The equipment shall comply with all the technical requirements of the present document at all times when operating within the boundary limits of the declared operational environmental profile. 4.2 Transmitter requirements 4.2.1 Frequency error 4.2.1.1 Definition The frequency error is defined in EN 300 113-1 [1], clause 7.1.1. 4.2.1.2 Limit The frequency error shall not exceed the limits in EN 300 113-1 [1], clause 7.1.3. 4.2.1.3 Conformance If the transmitter adjacent and alternate channels power (clause 5.3.4) has not been measured under extreme test conditions, then the conformance tests as defined in clause 5.3.1 shall be carried out. 4.2.2 Transmitter power (conducted) 4.2.2.1 Definition The transmitter power (conducted) is defined in EN 300 113-1 [1], clause 7.2.1. 4.2.2.2 Limit The transmitter power (conducted) shall not exceed the limits in EN 300 113-1 [1], clause 7.2.3. 4.2.2.3 Conformance Conformance tests as defined in clause 5.3.2 shall be carried out. 4.2.3 Maximum effective radiated power 4.2.3.1 Definition The maximum effective radiated power is defined in EN 300 113-1 [1], clause 7.3.1. 4.2.3.2 Limit The maximum effective radiated power shall not exceed the limits in EN 300 113-1 [1], clause 7.3.3. 4.2.3.3 Conformance Conformance tests as defined in clause 5.3.3 shall be carried out. SIST EN 300 113-2 V1.5.1:2012



ETSI ETSI EN 300 113-2 V1.5.1 (2011-11) 9 4.2.4 Adjacent and alternate channel power 4.2.4.1 Definition The adjacent and alternate channel power is defined in EN 300 113-1 [1], clause 7.4.1. 4.2.4.2 Limit The adjacent and alternate channel power shall not exceed the limits in EN 300 113-1 [1], clause 7.4.3. 4.2.4.3 Conformance Conformance tests as defined in clause 5.3.4 shall be carried out. 4.2.5 Unwanted emissions in the spurious domain 4.2.5.1 Definition The unwanted emissions in the spurious domain are defined in EN 300 113-1 [1], clause 7.5.1. 4.2.5.2 Limit The unwanted emissions in the spurious domain shall not exceed the limits in EN 300 113-1 [1], clause 7.5.4. 4.2.5.3 Conformance Conformance tests as defined in clause 5.3.5 shall be carried out. 4.2.6 Intermodulation attenuation 4.2.6.1 Definition The intermodulation a
...