ETSI TS 101 596-2 V6.1.1 (2018-01)

ETSI TS 101 596-2 V6.1.1 (2018-01)






TECHNICAL SPECIFICATION
Core Network and Interoperability Testing (INT);
Terminating Identification Presentation (TIP) and Terminating
Identification Restriction (TIR) using IP Multimedia (IM)
Core Network (CN) subsystem;
Conformance Test Specification;
TM
(3GPP Release 12);
Part 2: Test Suite Structure and Test Purposes (TSS&TP)

---------------------- Page: 1 ----------------------
2 ETSI TS 101 596-2 V6.1.1 (2018-01)



Reference
RTS/INT-00142-2
Keywords
conformance, IMS, testing, TIP, TIR, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2018.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM® and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TS 101 596-2 V6.1.1 (2018-01)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 5
3 Definitions, symbols and abbreviations . 5
3.1 Definitions . 5
3.2 Symbols . 5
3.3 Abbreviations . 6
4 Test Suite Structure (TSS) . 6
4.0 Table of Test suite Structure. 6
4.1 Configuration . 6
4.1.0 Introduction. 6
4.1.1 Testing of the AS . 6
4.1.2 Testing of the UE . 7
5 Test Purposes (TP) . 8
5.1 TP naming convention . 8
5.2 Test strategy . 8
5.3 TPs for Terminating Identification Presentation (TIP) and Terminating Identification Restriction (TIR) . 9
5.3.1 Actions at the originating UE . 9
5.3.2 Actions at the AS serving the originating UE . 11
5.3.3 Actions at the AS serving the terminating UE . 13
5.3.4 Actions at the terminating UE. 16
5.4 Interaction with other services . 18
5.4.1 Communication diversion services . 18
History . 20


ETSI

---------------------- Page: 3 ----------------------
4 ETSI TS 101 596-2 V6.1.1 (2018-01)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability
Testing (INT).
The present document is part 2 of a multi-part deliverable covering the Terminating Identification Presentation (TIP)
and Terminating Identification Restriction (TIR) using IP Multimedia (IM) Core Network (CN) subsystem;
Conformance Test Specification, as identified below:
Part 1: "Protocol Implementation Conformance Statement (PICS)";
Part 2: "Test Suite Structure and Test Purposes (TSS&TP)".
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.

ETSI

---------------------- Page: 4 ----------------------
5 ETSI TS 101 596-2 V6.1.1 (2018-01)
1 Scope
The present document provides the Test suite structure and test purposes for the Terminating Identification
Presentation (TIP) and Terminating Identification Restriction (TIR) using IP Multimedia (IM) Core Network (CN)
subsystem; Conformance Test Specification (based on ETSI TS 124 608 (3GPP Release 12) [1]).
2 References
2.1 Normative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
https://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are necessary for the application of the present document.
[1] ETSI TS 124 608: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); LTE; Terminating Identification Presentation (TIP) and
Terminating Identification Restriction (TIR) using IP Multimedia (IM) Core Network (CN)
subsystem; Protocol specification (3GPP TS 24.608 Release 12)".
[2] ETSI TS 101 596-1: "IMS Network Testing (INT); Terminating Identification Presentation (TIP)
and Terminating Identification Restriction (TIR) using IP Multimedia (IM) Core Network (CN)
subsystem; Conformance Test Specification; Part 1: Protocol Implementation Conformance
Statement (PICS)".
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
Not applicable.
3 Definitions, symbols and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in [1] apply.
3.2 Symbols
For the purposes of the present document, the symbols given in [1] apply.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI TS 101 596-2 V6.1.1 (2018-01)
3.3 Abbreviations
For the purposes of the present document, the abbreviations given in [1] and the following apply:
AS Application Server
CDIV Communication DIVersion
CN Core Network
CSCF Call Session Control Function
IM IP Multimedia
IP Internet Protocol
ISC IP Multimedia Subsystem Service Control
IUT Implementation Under Test
NNI Network-Network Interface
P-CSCF Proxy - CSCF
SIP Session Initiation Protocol
SUT System Under Test
TIP Terminating Identification Presentation
TIR Terminating Identification Restriction
TP Test Purposes
TSS Test Suite Structure
UA User Agent
UE User Equipment
URI Universal Resource Identifier
4 Test Suite Structure (TSS)
4.0 Table of Test suite Structure
User
OrigUserE TIP_U01_xxx
TermUserE TIP_U02_xxx

Network entity
OrigAS TIP_N01_xxx
DestAS TIP_N02_xxx

Interaction
CDIV TIP_N03_xxx

Figure 4.0-1: Test suite structure
4.1 Configuration
4.1.0 Introduction
The scope of the present document is to test the signalling and procedural aspects of the stage 3 requirements as
described in ETSI TS 124 608 [1]. The stage 3 description describes the requirements for several network entities and
also the requirements regarding terminal devices. Therefore several interfaces (reference points) are addressed to satisfy
the test of the different entities.
Therefore to test the appropriate entities the configurations below are applicable.
4.1.1 Testing of the AS
The AS entity is responsible for performing and managing services. The ISC interface is the appropriate access point for
testing.
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TS 101 596-2 V6.1.1 (2018-01)

Figure 4.1.1-1: Applicable interface to test AS functionalities
If the ISC interface is not accessible it is also possible to perform the test of the terminating AS using any NNI (Mw,
Mg, Mx,) interface (see figure 4.1.1-2) or originating AS using any NNI (Mw, Mg, Mx,) interface (see figure 4.1.1-3).

Figure 4.1.1-2: Applicable interfaces for tests using a (generic) NNI interface for terminating AS

Figure 4.1.1-3: Applicable interfaces for tests using a (generic) NNI interface for originating AS
4.1.2 Testing of the UE
There are special clauses in the protocol standard describing the procedures that apply at the originating and terminating
user equipment. Therefore the test configuration in figure 4.1.2-1 has been chosen.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI TS 101 596-2 V6.1.1 (2018-01)

Figure 4.1.2-1: Applicable configuration to test UE functionalities
5 Test Purposes (TP)
5.1 TP naming convention
TPs are numbered, starting at 001, within each group. Groups are organized according to the TSS. Additional references
are added to identify the actual test suite and whether it applies to the network or the user (see table 5.1-1).
Table 5.1-1: TP identifier naming convention scheme
Identifier: __
= supplementary service: e.g. "TIP"
= type of IUT: U User
N Network entity, e.g. P-CSCF
= group 2 digit field representing group reference according to TSS
= sequential number (001-999)

5.2 Test strategy
As the base standard ETSI TS 124 608 [1] contains no explicit requirements for testing, the TPs were generated as a
result of an analysis of the base standard and the PICS specification ETSI TS 101 596-1 [2].
All PICS items referred to in this clause are as specified in ETSI TS 101 596-1 [2] unless indicated otherwise by
another numbered reference.
ETSI

---------------------- Page: 8 ----------------------
9 ETSI TS 101 596-2 V6.1.1 (2018-01)
5.3 TPs for Terminating Identification Presentation (TIP) and
Terminating Identification Restriction (TIR)
5.3.1 Actions at the originating UE
TSS TP TIP/TIR reference Selection expression
User/OrigUserE TIP_U01_001 4.5.2.1 PICS 4.5.1/1
Test purpose:
The originating UE receives one P-Asserted-Identity in a sip URI.
Ensure that the Originating UE, receiving any non 100 response message defined as SIP_MESSAGE_VA containing a
P-Asserted-Identity heeder with a valid sip URI accepts the call following the basic request handling procedures.
SIP message: SIP_MESSAGE_VA
  P-Asserted-Identity:
Comments:
User equipment  Test equipment


INVITE

SIP_MESSAGE_VA

TSS TP TIP/TIR reference Selection expression
User/OrigUserE TIP_U01_002
4.5.2.1 PICS 4.5.1/1
Test purpose:
The originating UE receives one P-Asserted-Identity in a tel URI.
Ensure that the Originating UE, receiving any non 100 response message defined as SIP_MESSAGE_VA containing a
P-Asserted-Identity heeder with a valid tel URI, accepts the call following the basic request handling procedures.
SIP message: SIP_MESSAGE_VA
  P-Asserted-Identity:
Comments:
User equipment  Test equipment

 INVITE

SIP_MESSAGE_VA

TSS TP TIP/TIR reference Selection expression
User/OrigUserE TIP_U01_003 4.5.2.1 PICS 4.5.1/1
Test purpose:
The originating UE receives two P-Asserted-Identity headers in a sip URI and a tel URI.
Ensure that the Originating UE, receiving any non 100 response message defined as SIP_MESSAGE_VA containing
one P-Asserted-Identity header with a valid sip URI and one P-Asserted-Identity header with a valid tel URI, accepts
the call following the basic request handling procedures.
SIP message: SIP_MESSAGE_VA
  P-Asserted-Identity:
  P-Asserted-Identity:
Comments:
User equipment  UA S


INVITE
 SIP_MESSAGE_VA

ETSI

---------------------- Page: 9 ----------------------
10 ETSI TS 101 596-2 V6.1.1 (2018-01)
TSS TP TIP/TIR reference Selection expression
User/OrigUserE TIP_U01_004 4.5.2.1 PICS 4.5.1/1
Test purpose:
The originating UE receives a Privacy header field value 'id' indicating the TIR service.
Ensure that the Originating UE, receiving any non 100 response message defined as SIP_MESSAGE_VA with a
Privacy header with privacy type of "id" and without P-Asserted-Identity headers, accepts the call following the basic
request handling procedures.
SIP message: SIP_MESSAGE_VA
  Privacy: id
Comments:
User equipment  Test equipment

 INVITE
 SIP_MESSAGE_VA

Values for tests purposes TIP_U01_001 to TIP_U02_004
VA_01 180 Ringing
VA_02 183 Session progress
VA_03 200 OK

TSS TP TIP/TIR reference Selection expression
User/OrigUserE TIP_U01_005 4.5.2.1 PICS 4.5.1/1 AND

PICS 4.6.1/1
Test purpose:
The originating user is able to send the "from-change" tag in the Supported header in the initial INVITE.
Ensure that the Originating UE sends a "from-change" tag in the Supported header in the initial INVITE.
SIP message: INVITE Supported "from-change"
Comments:
User equipment  Test equipment


INVITE with "from-change" tag

TSS TP TIP/TIR reference Selection expression
Syntax/OrigUserE TIP_U01_006 4.5.2.1 PICS 4.5.1/1 AND
PICS 4.6.1/1
Test purpose:
The originating user is able to receive a connected identity in the From header of an UPDATE request.
Ensure that the Originating UE is able to receive a second identity in the From header of an UPDATE request if the UE
indicates the support of this procedure by sending the "from-change" tag in the Supported header in the initial INVITE
and this identity is displayed to the user.
SIP message: INVITE Supported "from-change"
UPDATE From
Comments:
User equipment SUT Test equipment


INVITE with "from-change" tag
 180 Ringing
 200 OK INVITE

ACK

 UPDATE with new URI in From header

200 OK UPDATE

ETSI

---------------------- Page: 10 ----------------------
11 ETSI TS 101 596-2 V6.1.1 (2018-01)
5.3.2 Actions at the AS serving the originating UE
TSS TP TIP/TIR reference Selection expression
Signalling/OrigNetw TIP_N01_001 4.3.2 PICS 4.5.1/2 AND
PICS 4.7.1/3
Test purpose:
The originating user subscribes to the TIP service.
Ensure that for originating users that subscribe to TIP simulation service, if network provided identity information about
the terminator is available, and if presentation is not restricted, the AS shall pass that information in any non
100 response message defined as SIP_MESSAGE_VA.
Precondition: The originating user has subscribed to the TIP service
SIP messages: SIP_MESSAGE_VA1: P-Asserted-Identity
SIP_MESSAGE_VA2: P-Asserted-Identity
Comments:
Test equipment AS Test equipment
...