ETSI EN 300 019-2-1 V2.2.1 (2014-10)

ETSI EN 300 019-2-1 V2.2.1 (2014-10)






EUROPEAN STANDARD
Environmental Engineering (EE);
Environmental conditions and environmental tests
for telecommunications equipment;
Part 2-1: Specification of environmental tests;
Storage

---------------------- Page: 1 ----------------------
2 ETSI EN 300 019-2-1 V2.2.1 (2014-10)



Reference
REN/EE-0157
Keywords
environment, equipment practice, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
Contents
Intellectual Property Rights . 4
Foreword . 4
Modal verbs terminology . 5
1 Scope . 6
2 References . 6
2.1 Normative references . 6
2.2 Informative references . 7
3 Environmental test specifications . 7
3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations . 8
3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations . 11
3.3 Specification T 1.3: Non-weatherprotected storage locations and T 1.3 E: Non-weatherprotected storage
locations - extended . 14
4 Notes to tables . 19
4.1 General note . 19
4.2 Notes to tables 1 to 7 . 19
Annex A (informative): Bibliography . 21
History . 22

ETSI

---------------------- Page: 3 ----------------------
4 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE).
The present document is part 2, sub-part 1 of a multi-part deliverable covering the environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests":
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic and biological conditions, chemically
and mechanically active substances and mechanical conditions during storage, transportation and in use.
Part 2 specifies the recommended test severities and test methods for the different environmental classes.

National transposition dates
Date of adoption of this EN: 1 October 2014
Date of latest announcement of this EN (doa): 31 January 2015
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 July 2015
Date of withdrawal of any conflicting National Standard (dow): 31 July 2015

ETSI

---------------------- Page: 4 ----------------------
5 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "may not", "need", "need not", "will",
"will not", "can" and "cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms
for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI

---------------------- Page: 5 ----------------------
6 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
1 Scope
The present document specifies test severities and methods for verification of the required resistibility of equipment
according to the relevant environmental class.
The tests defined in the present document apply to storage of equipment covering the environmental conditions stated in
EN 300 019-1-1 [1].
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 019-1-1 (2014): "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[2] Void.
[3] Void.
[4] IEC 60068-2-1:2007: "Environmental testing - Part 2-1: Tests - Test A: Cold".
[5] IEC 60068-2-2:2007: "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[6] IEC 60068-2-6:2007: "Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)".
[7] IEC 60068-2-14:2009: "Environmental testing - Part 2-14: Tests - Test N: Change of temperature".
[8] IEC 60068-2-18:2000: "Environmental testing - Part 2-18: Tests - Test R and guidance: Water".
[9] IEC 60068-2-27:2008: "Environmental testing. Part 2-27: Tests - Test Ea and guidance: Shock".
[10] IEC 60068-2-30:2005: "Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic
(12 + 12 hour cycle)".
[11] IEC 60068-2-78:2012: "Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady
state".
[12] IEC 60068-2-64:2008: "Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband
random and guidance".
ETSI

---------------------- Page: 6 ----------------------
7 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 019-2-0 (2003): "Equipment Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
[i.2] IEC 60068-2-68:1994: "Environmental testing - Part 2: Tests - Test L: Dust and sand".
[i.3] IEC 60068-2: "Environmental testing - Part 2: Tests".
3 Environmental test specifications
The detailed descriptions of the environmental conditions are given in clauses 4 and 5 of EN 300 019-1-1 [1].
EN 300 019-2-0 [i.1] forms a general overview of part 2 of the present document.
If the equipment is normally stored in a packed state then it shall be tested in its packaging.
ETSI

---------------------- Page: 7 ----------------------
8 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations
This specification shall apply to weatherprotected or partially weather-controlled storage locations having partially temperature or humidity control. See tables 1 and 2.
Table 1: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - climatic tests
Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
low (°C) -5 -5 72 h IEC 60068-2-1 [4] Ab: Cold
Air high (°C) +45 +45 or +55 72 h IEC 60068-2-2 [5] Bb: Dry heat 2
temperature
change (°C/min) 0,5 none  3
 low (%) 5 none  10
relative high (%) 95 93 96 h IEC 60068-2-78 [11] Cab: Damp heat 5
steady state
 (°C) +30
Humidity condensation yes none  6
3

absolute 1 none  10
low (g/m )
3
 29   8
high (g/m )
pressure low (kPa) 70 none  9
Air high (kPa) 106 none  9
speed (m/s) 1 none  10
rain intensity no
Water low temperature no
other sources no
icing & frosting yes   10
2
Radiation solar 700   13
(W/m )
2
heat 600   13
(W/m )
ETSI

---------------------- Page: 8 ----------------------
9 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
3
sulphur 0,3/1,0 none  14
SO (mg/m )
2
3
 0,1/0,5 none  14
HS (mg/m )
2
 salts sea and road salt mist none  14
3
Chemically chlorine 0,1/0,3 none  14
Cl (mg/m )
2
3
active 0,1/0,5 none  14
HCI (mg/m )
3
substances nitrogen 0,5/1,0 none  14
NO (mg/m )
x
3
 1,0/3,0 none  14
NH (mg/m )
3
3
hydrogen fluoride 0,01/0,03 none  14
HF (mg/m )
3
ozone 0,05/0,1 none  14
O (mg/m )
3
Mechanically dust Sedimentation 1,5 none  15
2
(mg/(m h))
3
active 0,2 none  15
suspension (mg/m )
3
substances sand 30 none  15
(mg/m )
Flora and micro organisms negligible
Fauna rodents, insects negligible
no = this condition does not occur in this class.
NOTE: (n = number of note), see clause 4.2.

ETSI

---------------------- Page: 9 ----------------------
10 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
Table 2: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - mechanical tests
Environmental parameter Environmental Environmental test specification T 1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
Fc: Vibration
 velocity (mm/s) 5 IEC 60068-2-6 [6] 17
(sinusoidal)
 displacement (mm) 1,5
2
sinusoidal 5 2
acceleration (m/s )
2-9 9-200 5-62 62-200 3 x 5 sweep
frequency range (Hz)
cycles
Vibration 3
axes of vibration
2 3 IEC 60068-2-64 [12] Fh: Vibration,
  0,02 18
ASD (m /s )
broad-band random
random +12 -12 3 x 30 minutes
(dB/oct)
(digital control)
5-10 10-50 50-100
frequency range (Hz)
3
axes of vibration
Shocks shocks shock spectrum Type L none  19a
duration (ms) 22
2
40
acceleration (m/s )
number of shocks
directions of shocks
Load static load (kPa) 5 none  20
no = this condition does not occur in this class.
NOTE: (n = number of note), see clause 4.2.

ETSI

---------------------- Page: 10 ----------------------
11 ETSI EN 300 019-2-1 V2.2.1 (2014-10)
3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations
This specification shall apply to weatherprotected or partially weatherprotected storage locations having neither temperature nor humidity control. See tables 3 and 4.
Table 3: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - climatic tests
Environmental parameter Environmental Environmental test specification T1.2: Weatherprotected,
Class 1.2 not temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
low (°C) -25 -25 72 h IEC 60068-2-1 [4] Ab: Cold
Air high (°C) +55 +55 or +70 72 h IEC 60068-2-2 [5] Bb: Dry heat 2
temperature change (°C/min) 0,5 none  3
 low (%) 10 none  10
 high (%) 100 93 96 h IEC 60068-2-78 [11] Cab: Damp heat 5
steady state
relative (°C) +30
Humidity condensation yes   7
(%) 90-100 2 cycles IEC 60068-2-30 [
...

Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)






European Standard
Environmental Engineering (EE);
Environmental conditions and environmental tests
for telecommunications equipment;
Part 2-1: Specification of environmental tests;
Storage

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)



Reference
REN/EE-0157
Keywords
environment, equipment practice, testing
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2014.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members.
TM
3GPP and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
Contents
Intellectual Property Rights . 4
Foreword . 4
1 Scope . 5
2 References . 5
2.1 Normative references . 5
2.2 Informative references . 6
3 Environmental test specifications . 6
3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations . 7
3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations . 10
3.3 Specification T 1.3: Non-weatherprotected storage locations and T 1.3 E: Non-weatherprotected storage
locations - extended . 13
4 Notes to tables . 18
4.1 General note . 18
4.2 Notes to tables 1 to 7 . 18
Annex A (informative): Bibliography . 20
History . 21

ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://ipr.etsi.org).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This draft European Standard (EN) has been produced by ETSI Technical Committee Environmental Engineering (EE),
and is now submitted for the combined Public Enquiry and Vote phase of the ETSI standards EN Approval Procedure.
The present document is part 2, sub-part 1 of a multi-part deliverable covering the environmental conditions and
environmental tests for telecommunications equipment, as identified below:
Part 1: "Classification of environmental conditions";
Part 2: "Specification of environmental tests":
Sub-part 0: "Introduction";
Sub-part 1: "Storage";
Sub-part 2: "Transportation";
Sub-part 3: "Stationary use at weatherprotected locations";
Sub-part 4: "Stationary use at non-weatherprotected locations";
Sub-part 5: "Ground vehicle installations";
Sub-part 6: "Ship environments";
Sub-part 7: "Portable and non-stationary use";
Sub-part 8: "Stationary use at underground locations".
Part 1 specifies different standardized environmental classes covering climatic and biological conditions, chemically
and mechanically active substances and mechanical conditions during storage, transportation and in use.
Part 2 specifies the recommended test severities and test methods for the different environmental classes.

Proposed national transposition dates
Date of latest announcement of this EN (doa): 3 months after ETSI publication
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 6 months after doa
Date of withdrawal of any conflicting National Standard (dow): 6 months after doa

ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
1 Scope
The present document specifies test severities and methods for verification of the required resistibility of equipment
according to the relevant environmental class.
The tests defined in the present document apply to storage of equipment covering the environmental conditions stated in
EN 300 019-1-1 [1].
2 References
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
reference document (including any amendments) applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
2.1 Normative references
The following referenced documents are necessary for the application of the present document.
[1] ETSI EN 300 019-1-1 (2013): "Environmental Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 1-1: Classification of environmental
conditions; Storage".
[2] Void.
[3] Void.
[4] IEC 60068-2-1:2007: "Environmental testing - Part 2-1: Tests - Test A: Cold".
[5] IEC 60068-2-2:2007: "Environmental testing - Part 2-2: Tests - Test B: Dry heat".
[6] IEC 60068-2-6:2007: "Environmental testing - Part 2-6: Tests - Test Fc: Vibration (sinusoidal)".
[7] IEC 60068-2-14:2009: "Environmental testing - Part 2-14: Tests - Test N: Change of temperature".
[8] IEC 60068-2-18:2000: "Environmental testing - Part 2-18: Tests - Test R and guidance: Water".
[9] IEC 60068-2-27:2008: "Environmental testing. Part 2-27: Tests - Test Ea and guidance: Shock".
[10] IEC 60068-2-30:2005: "Environmental testing - Part 2-30: Tests - Test Db: Damp heat, cyclic
(12 + 12 hour cycle)".
[11] IEC 60068-2-78:2012: "Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady
state".
[12] IEC 60068-2-64:2008: "Environmental testing - Part 2-64: Tests - Test Fh: Vibration, broadband
random and guidance".
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
2.2 Informative references
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] ETSI EN 300 019-2-0 (2003): "Equipment Engineering (EE); Environmental conditions and
environmental tests for telecommunications equipment; Part 2-0: Specification of environmental
tests; Introduction".
[i.2] IEC 60068-2-68:1994: "Environmental testing - Part 2: Tests - Test L: Dust and sand".
[i.3] IEC 60068-2: "Environmental testing - Part 2: Tests".
3 Environmental test specifications
The detailed descriptions of the environmental conditions are given in clauses 4 and 5 of EN 300 019-1-1 [1].
EN 300 019-2-0 [i.1] forms a general overview of part 2 of the present document.
If the equipment is normally stored in a packed state then it shall be tested in its packaging.
ETSI

---------------------- Page: 6 ----------------------
7 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
3.1 Specification T 1.1: Weatherprotected, partly temperature-controlled storage locations
This specification shall apply to weatherprotected or partially weather-controlled storage locations having partially temperature or humidity control. See tables 1 and 2.
Table 1: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - climatic tests
Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
low (°C) -5 -5 72 h IEC 60068-2-1 [4] Ab: Cold
Air high (°C) +45 +45 or +55 72 h IEC 60068-2-2 [5] Bb: Dry heat 2
temperature
change (°C/min) 0,5 none  3
 low (%) 5 none  10
relative high (%) 95 93 96 h IEC 60068-2-78 Cab: Damp heat steady 5
[11] state
 (°C) +30
Humidity condensation yes none  6
3

absolute 1 none  10
low (g/m )
3
 29   8
high (g/m )
pressure low (kPa) 70 none  9
Air high (kPa) 106 none  9
speed (m/s) 1 none  10
rain intensity no
Water low temperature no
other sources no
icing & frosting yes   10
2
Radiation solar 700   13
(W/m )
2
heat 600   13
(W/m )
ETSI

---------------------- Page: 7 ----------------------
8 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
Environmental parameter Environmental Environmental test specification T1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
3
sulphur 0,3/1,0 none  14
SO (mg/m )
2
3
 0,1/0,5 none  14
HS (mg/m )
2
 salts sea and road salt mist none  14
3
Chemically chlorine 0,1/0,3 none  14
Cl (mg/m )
2
3
active 0,1/0,5 none  14
HCI (mg/m )
3
substances nitrogen 0,5/1,0 none  14
NO (mg/m )
x
3
 1,0/3,0 none  14
NH (mg/m )
3
3
hydrogen fluoride 0,01/0,03 none  14
HF (mg/m )
3
ozone 0,05/0,1 none  14
O (mg/m )
3
Mechanically dust Sedimentation 1,5 none  15
2
(mg/(m h))
3
active 0,2 none  15
suspension (mg/m )
3
substances sand 30 none  15
(mg/m )
Flora and micro organisms negligible
Fauna rodents, insects negligible
no = this condition does not occur in this class.
NOTE: (n = number of note), see clause 4.2.

ETSI

---------------------- Page: 8 ----------------------
9 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
Table 2: Test specification T 1.1: Weatherprotected, partly temperature-controlled storage locations - mechanical tests
Environmental parameter Environmental Environmental test specification T 1.1: Weatherprotected,
Class 1.1 partly temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
Fc: Vibration
 velocity (mm/s) 5 IEC 60068-2-6 [6] 17
(sinusoidal)
 displacement (mm) 1,5
2
sinusoidal 5 2
acceleration (m/s )
2-9 9-200 5-62 62-200 3 x 5 sweep
frequency range (Hz)
cycles
Vibration 3
axes of vibration
2 3 IEC 60068-2-64 [12] Fh: Vibration,
  0,02 18
ASD (m /s )
broad-band random
random +12 -12 3 x 30 minutes
(dB/oct)
(digital control)
5-10 10-50 50-100
frequency range (Hz)
3
axes of vibration
Shocks shocks shock spectrum Type L none  19a
duration (ms) 22
2
40
acceleration (m/s )
number of shocks
directions of shocks
Load static load (kPa) 5 none  20
no = this condition does not occur in this class.
NOTE: (n = number of note), see clause 4.2.

ETSI

---------------------- Page: 9 ----------------------
10 Draft ETSI EN 300 019-2-1 V2.1.6 (2014-06)
3.2 Specification T 1.2: Weatherprotected, not temperature-controlled storage locations
This specification shall apply to weatherprotected or partially weatherprotected storage locations having neither temperature nor humidity control. See tables 3 and 4.
Table 3: Test specification T 1.2: Weatherprotected, not temperature-controlled storage locations - climatic tests
Environmental parameter Environmental Environmental test specification T1.2: Weatherprotected,
Class 1.2 not temperature-controlled storage locations
Type Parameter Detail parameter Characteristic Test severity Duration Reference Method Notes
severity
low (°C) -25 -25 72 h IEC 60068-2-1 [4] Ab: Cold
Air high (°C) +55 +55 or +70 72 h IEC 60068-2-2 [5] Bb: Dry heat 2
temperature change (°C/min) 0,5 none  3
 low (%) 10 none  10
 high (%) 100 93 96 h IEC 60068-2-78 Cab: Damp heat 5
[11] steady state
relative (°C) +30
Humidity condensation yes   7
(%) 90-100 2 cycles IEC 60068-2-30 Db: Damp heat cyclic
[10]
(°C) +30 Variant 1
3
absolute 0,5 none  10
low (g/m )
3
 29   6
high (g/m )
pressure low (kPa) 70 none  9
Air high (kPa) 106 none  9
speed (m/s) 30 none  10
rain intensity no
Water low temperature no

...