ETSI EN 302 217-2 V3.2.2 (2020-02)

SLOVENSKI STANDARD
SIST EN 302 217-2 V3.2.2:2020
01-april-2020
Fiksni radijski sistemi - Karakteristike in zahteve za opremo tipa točka-točka in
antene - 2. del: Digitalni sistemi, ki delujejo v frekvenčnih pasovih od 1 GHz do 86
GHz - Harmonizirani standard za dostop do radijskega spektra
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 2: Digital systems operating in frequency bands from 1 GHz to 86
GHz - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 302 217-2 V3.2.2 (2020-02)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
SIST EN 302 217-2 V3.2.2:2020 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 302 217-2 V3.2.2:2020

---------------------- Page: 2 ----------------------
SIST EN 302 217-2 V3.2.2:2020
ETSI EN 302 217-2 V3.2.2 (2020-02)






HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
SIST EN 302 217-2 V3.2.2:2020
 2 ETSI EN 302 217-2 V3.2.2 (2020-02)



Reference
REN/ATTM-0438
Keywords
antenna, DFRS, digital, DRRS, FWA,
point-to-point, radio, regulation, transmission

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2020.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
SIST EN 302 217-2 V3.2.2:2020
 3 ETSI EN 302 217-2 V3.2.2 (2020-02)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 10
Introduction . 10
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definition of terms, symbols and abbreviations . 15
3.1 Terms . 15
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 Framework for categorization of system . 15
4.1.0 The "Manufacturer declarations" concept . 15
4.1.1 Introduction and equipment flexibility . 16
4.1.2 Operating frequency bands and channel arrangements . 17
4.1.3 Spectral efficiency classes . 17
4.1.4 System alternatives . 18
4.1.5 Channel arrangements and utilization . 19
4.1.6 Specific requirements for frequency bands . 19
4.1.7 Minimum RIC density for spectral efficiency class selection . 20
4.1.8 System identification and traffic loading . 21
4.1.9 Environmental profile . 22
4.2 Transmitter requirements . 22
4.2.0 General: system loading . 22
4.2.1 Transmitter power and power environmental variation . 23
4.2.1.1 Maximum power and EIRP . 23
4.2.1.2 Combined TX power output and EIRP limits . 23
4.2.1.3 Output power environmental variation. 24
4.2.2 Transmitter power and frequency control . 24
4.2.2.1 Power Control (ATPC and RTPC) . 24
4.2.2.1.0 General background . 24
4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 24
4.2.2.1.2 Remote Transmit Power Control (RTPC) . 24
4.2.2.2 Remote Frequency Control (RFC) . 24
4.2.3 Radio Frequency (RF) spectrum mask. 25
4.2.3.1 Limits background . 25
4.2.3.2 Limits . 28
4.2.4 Discrete CW components exceeding the spectrum mask limit . 41
4.2.4.1 Discrete CW components at the symbol rate . 41
4.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 41
4.2.5 Unwanted emissions in the spurious domain - external . 42
4.2.6 Dynamic Change of Modulation Order . 43
4.2.7 Frequency tolerance . 43
4.2.8 Emission limitations outside the allocated band . 44
4.3 Receiver requirements . 44
4.3.0 General: System loading . 44
4.3.1 Unwanted emissions in the spurious domain - external . 44
4.3.2 BER as a function of receiver input signal level RSL . 44
4.3.3 Receiver selectivity . 45
4.3.3.1 Introduction . 45
4.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 45
4.3.3.2.1 Requirements basic . 45
ETSI

---------------------- Page: 5 ----------------------
SIST EN 302 217-2 V3.2.2:2020
 4 ETSI EN 302 217-2 V3.2.2 (2020-02)
4.3.3.2.2 Limits for co-channel and first adjacent channel . 46
4.3.3.2.3 Limits for second adjacent channel interference . 46
4.3.3.3 CW spurious interference (blocking & spurious response rejection) . 47
4.4 Antenna Characteristics . 48
4.4.1 Integral antennas or dedicated antennas. 48
4.4.1.1 Introduction . 48
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) . 48
4.4.1.3 Antenna gain . 48
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) . 48
4.4.2 Guidelines for stand-alone antennas . 48
5 Testing for compliance with technical requirements . 49
5.1 Environmental and other conditions for testing . 49
5.1.1 Environmental conditions . 49
5.1.2 Other basic conditions . 49
5.2 Test methods for the transmitter . 50
5.2.0 General test summary . 50
5.2.1 Transmitter power and power environmental variation . 51
5.2.1.1 Transmitter power and EIRP . 51
5.2.1.2 Combined TX power output and EIRP limits . 52
5.2.1.3 Output power environmental variation. 52
5.2.2 Transmitter power and frequency control . 52
5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 52
5.2.2.1.1 ATPC . 52
5.2.2.1.2 RTPC . 52
5.2.2.2 Remote Frequency Control (RFC) . 52
5.2.3 RF spectrum mask . 53
5.2.4 Discrete CW components exceeding the spectrum mask limit . 53
5.2.5 Unwanted emissions in the spurious domain - external . 53
5.2.6 Dynamic Change of Modulation Order . 53
5.2.7 Radio frequency tolerance . 54
5.3 Test methods for the receiver . 54
5.3.0 General test summary . 54
5.3.1 Unwanted emissions in the spurious domain - external . 55
5.3.2 BER as a function of receiver input signal level (RSL) . 55
5.3.3 Receiver selectivity . 56
5.3.3.1 Void. 56
5.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 56
5.3.3.2.1 Co-channel and first adjacent channel . 56
5.3.3.2.2 Second adjacent channel . 56
5.3.3.3 CW spurious interference . 56
5.4 Antenna test methods for systems with integral or dedicated antenna . 56
5.4.0 General test summary . 56
5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 57
5.4.2 Antenna gain . 57
5.4.3 Antenna Cross-Polar Discrimination (XPD) . 57
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 58
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz . 60
B.1 Introduction . 60
B.2 General characteristics . 60
B.2.1 Frequency characteristics and channel arrangements . 60
B.2.2 Transmission capacities . 61
B.3 Transmitter . 61
B.3.1 General requirements . 61
B.3.2 RF spectrum masks options . 62
B.4 Receiver . 62
B.4.1 General requirements . 62
ETSI

---------------------- Page: 6 ----------------------
SIST EN 302 217-2 V3.2.2:2020
 5 ETSI EN 302 217-2 V3.2.2 (2020-02)
B.4.2 BER as a function of receiver input signal level (RSL) . 62
B.4.3 Co-channel "external" and adjacent channels interference sensitivity . 63
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz and 56/60 MHz) . 65
C.1 Introduction . 65
C.2 General characteristics . 65
C.2.1 Frequency characteristics and channel arrangements . 65
C.2.2 Transmission capacities . 66
C.3 Transmitter . 67
C.3.1 General requirements . 67
C.3.2 RF spectrum masks . 67
C.4 Receiver . 67
C.4.1 General requirements . 67
C.4.2 BER as a function of Receiver input Signal Level (RSL) . 67
C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 69
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation
40 MHz) . 70
D.1 Introduction . 70
D.2 General characteristics . 70
D.2.1 Frequency characteristics and channel arrangements . 70
D.2.2 Transmission capacities . 70
D.3 Transmitter . 71
D.3.1 General requirements . 71
D.3.2 RF spectrum masks . 71
D.4 Receiver . 72
D.4.1 General requirements . 72
D.4.2 BER as a function of Receiver input Signal Level (RSL) . 72
D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 73
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 74
E.1 Introduction . 74
E.2 General characteristics . 74
E.2.1 Frequency characteristics and channel arrangements . 74
E.2.2 Transmission capacities . 75
E.3 Transmitter . 75
E.3.1 General requirements . 75
E.3.2 RF spectrum masks . 75
E.4 Receiver . 76
E.4.1 General requirements . 76
E.4.2 BER as a function of Receiver input Signal Level (RSL) . 76
E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 79
Annex F (normative): Frequency bands from 23 GHz to 42 GHz . 80
F.1 Introduction . 80
F.2 General characteristics . 80
F.2.1 Frequency characteristics and channel arrangements . 80
F.2.2 Transmission capacities . 81
F.3 Transmitter . 81
F.3.1 General requirements . 81
F.3.2 RF spectrum masks . 82
ETSI

---------------------- Page: 7 ----------------------
SIST EN 302 217-2 V3.2.2:2020
 6 ETSI EN 302 217-2 V3.2.2 (2020-02)
F.4 Receiver . 82
F.4.1 General requirements . 82
F.4.2 BER as a function of Receiver input Signal Level (RSL) . 82
F.4.3 Co-channel "external" and adjacent channel interference sensitivity . 85
Annex G (normative): Frequency bands from 50 GHz to 55 GHz . 86
G.1 Introduction . 86
G.2 General characteristics . 86
G.2.1 Frequency characteristics and channel arrangements . 86
G.2.2 Transmission capacities . 87
G.3 Transmitter . 87
G.3.1 General requirements .
...

Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)






HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)



Reference
REN/ATTM-0438
Keywords
antenna, DFRS, digital, DRRS, FWA,
point-to-point, radio, regulation, transmission

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 10
Introduction . 10
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definition of terms, symbols and abbreviations . 15
3.1 Terms . 15
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 Framework for categorization of system . 15
4.1.0 The "Manufacturer declarations" concept . 15
4.1.1 Introduction and equipment flexibility . 16
4.1.2 Operating frequency bands and channel arrangements . 17
4.1.3 Spectral efficiency classes . 17
4.1.4 System alternatives . 18
4.1.5 Channel arrangements and utilization . 19
4.1.6 Specific requirements for frequency bands . 19
4.1.7 Minimum RIC density for spectral efficiency class selection . 20
4.1.8 System identification and traffic loading . 21
4.1.9 Environmental profile . 22
4.2 Transmitter requirements . 22
4.2.0 General: system loading . 22
4.2.1 Transmitter power and power environmental variation . 23
4.2.1.1 Maximum power and EIRP . 23
4.2.1.2 Combined TX power output and EIRP limits . 23
4.2.1.3 Output power environmental variation. 24
4.2.2 Transmitter power and frequency control . 24
4.2.2.1 Power Control (ATPC and RTPC) . 24
4.2.2.1.0 General background . 24
4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 24
4.2.2.1.2 Remote Transmit Power Control (RTPC) . 24
4.2.2.2 Remote Frequency Control (RFC) . 24
4.2.3 Radio Frequency (RF) spectrum mask. 25
4.2.3.1 Limits background . 25
4.2.3.2 Limits . 28
4.2.4 Discrete CW components exceeding the spectrum mask limit . 41
4.2.4.1 Discrete CW components at the symbol rate . 41
4.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 41
4.2.5 Unwanted emissions in the spurious domain - external . 42
4.2.6 Dynamic Change of Modulation Order . 43
4.2.7 Frequency tolerance . 43
4.2.8 Emission limitations outside the allocated band . 44
4.3 Receiver requirements . 44
4.3.0 General: System loading . 44
4.3.1 Unwanted emissions in the spurious domain - external . 44
4.3.2 BER as a function of receiver input signal level RSL . 44
4.3.3 Receiver selectivity . 45
4.3.3.1 Introduction . 45
4.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 45
4.3.3.2.1 Requirements basic . 45
ETSI

---------------------- Page: 3 ----------------------
4 Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)
4.3.3.2.2 Limits for co-channel and first adjacent channel . 46
4.3.3.2.3 Limits for second adjacent channel interference . 46
4.3.3.3 CW spurious interference (blocking & spurious response rejection) . 47
4.4 Antenna Characteristics . 48
4.4.1 Integral antennas or dedicated antennas. 48
4.4.1.1 Introduction . 48
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) . 48
4.4.1.3 Antenna gain . 48
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) . 48
4.4.2 Guidelines for stand-alone antennas . 48
5 Testing for compliance with technical requirements . 49
5.1 Environmental and other conditions for testing . 49
5.1.1 Environmental conditions . 49
5.1.2 Other basic conditions . 49
5.2 Test methods for the transmitter . 50
5.2.0 General test summary . 50
5.2.1 Transmitter power and power environmental variation . 51
5.2.1.1 Transmitter power and EIRP . 51
5.2.1.2 Combined TX power output and EIRP limits . 52
5.2.1.3 Output power environmental variation. 52
5.2.2 Transmitter power and frequency control . 52
5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 52
5.2.2.1.1 ATPC . 52
5.2.2.1.2 RTPC . 52
5.2.2.2 Remote Frequency Control (RFC) . 52
5.2.3 RF spectrum mask . 53
5.2.4 Discrete CW components exceeding the spectrum mask limit . 53
5.2.5 Unwanted emissions in the spurious domain - external . 53
5.2.6 Dynamic Change of Modulation Order . 53
5.2.7 Radio frequency tolerance . 54
5.3 Test methods for the receiver . 54
5.3.0 General test summary . 54
5.3.1 Unwanted emissions in the spurious domain - external . 55
5.3.2 BER as a function of receiver input signal level (RSL) . 55
5.3.3 Receiver selectivity . 56
5.3.3.1 Void. 56
5.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 56
5.3.3.2.1 Co-channel and first adjacent channel . 56
5.3.3.2.2 Second adjacent channel . 56
5.3.3.3 CW spurious interference . 56
5.4 Antenna test methods for systems with integral or dedicated antenna . 56
5.4.0 General test summary . 56
5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 57
5.4.2 Antenna gain . 57
5.4.3 Antenna Cross-Polar Discrimination (XPD) . 57
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 58
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz . 60
B.1 Introduction . 60
B.2 General characteristics . 60
B.2.1 Frequency characteristics and channel arrangements . 60
B.2.2 Transmission capacities . 60
B.3 Transmitter . 61
B.3.1 General requirements . 61
B.3.2 RF spectrum masks options . 62
B.4 Receiver . 62
B.4.1 General requirements . 62
ETSI

---------------------- Page: 4 ----------------------
5 Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)
B.4.2 BER as a function of receiver input signal level (RSL) . 62
B.4.3 Co-channel "external" and adjacent channels interference sensitivity . 63
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz and 56/60 MHz) . 65
C.1 Introduction . 65
C.2 General characteristics . 65
C.2.1 Frequency characteristics and channel arrangements . 65
C.2.2 Transmission capacities . 66
C.3 Transmitter . 67
C.3.1 General requirements . 67
C.3.2 RF spectrum masks . 67
C.4 Receiver . 67
C.4.1 General requirements . 67
C.4.2 BER as a function of Receiver input Signal Level (RSL) . 67
C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 69
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation
40 MHz) . 70
D.1 Introduction . 70
D.2 General characteristics . 70
D.2.1 Frequency characteristics and channel arrangements . 70
D.2.2 Transmission capacities . 70
D.3 Transmitter . 71
D.3.1 General requirements . 71
D.3.2 RF spectrum masks . 71
D.4 Receiver . 72
D.4.1 General requirements . 72
D.4.2 BER as a function of Receiver input Signal Level (RSL) . 72
D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 73
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 74
E.1 Introduction . 74
E.2 General characteristics . 74
E.2.1 Frequency characteristics and channel arrangements . 74
E.2.2 Transmission capacities . 75
E.3 Transmitter . 75
E.3.1 General requirements . 75
E.3.2 RF spectrum masks . 75
E.4 Receiver . 76
E.4.1 General requirements . 76
E.4.2 BER as a function of Receiver input Signal Level (RSL) . 76
E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 79
Annex F (normative): Frequency bands from 23 GHz to 42 GHz . 80
F.1 Introduction . 80
F.2 General characteristics . 80
F.2.1 Frequency characteristics and channel arrangements . 80
F.2.2 Transmission capacities . 81
F.3 Transmitter . 81
F.3.1 General requirements . 81
F.3.2 RF spectrum masks . 82
ETSI

---------------------- Page: 5 ----------------------
6 Final draft ETSI EN 302 217-2 V3.2.1 (2019-12)
F.4 Receiver . 82
F.4.1 General requirements . 82
F.4.2 BER as a function of Receiver input Signal Level (RSL) . 82
F.4.3 Co-channel "external" and adjacent channel interference sensitivity . 85
Annex G (normative): Frequency bands from 50 GHz to 55 GHz . 86
G.1 Introduction . 86
G.2 General characteristics . 86
G.2.1 Frequency characteristics and channel arrangements . 86
G.2.2 Transmission capacities . 87
G.3 Transmitter . 87
G.3.1 General requirements . 87
G.3.2 RF spectrum masks . 87
G.4 Receiver . 87
G.4.1 General requirements . 87
G.4.2 BER as a function of Receiver input Signal Level (RSL) . 88
G.4.3 Co-channel "external" and adjacent channel interference sensitivity . 88
Annex H (normative): Frequency band 57 GHz to 66 GHz . 89
H.1 Introduction . 89
H.2 General characterist
...

Draft ETSI EN 302 217-2 V3.2.0 (2019-03)






HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum

---------------------- Page: 1 ----------------------
2 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)



Reference
REN/ATTM-0438
Keywords
antenna, DFRS, digital, DRRS, FWA, point-to-
point, radio, regulation, transmission

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 10
Introduction . 10
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definition of terms, symbols and abbreviations . 15
3.1 Terms . 15
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 Framework for categorisation of system . 15
4.1.0 Generality . 15
4.1.1 Introduction and equipment flexibility . 15
4.1.2 Operating frequency bands and channel arrangements . 17
4.1.3 Spectral efficiency classes . 17
4.1.4 System alternatives . 18
4.1.5 Channel arrangements and utilization . 18
4.1.6 Specific Requirements for frequency bands . 19
4.1.7 Minimum RIC density for spectral efficiency class selection . 20
4.1.8 Payload flexibility . 20
4.1.9 System identification and traffic loading . 21
4.1.10 Environmental profile . 22
4.2 Transmitter requirements . 22
4.2.0 General: system loading . 22
4.2.1 Transmitter power and power environmental variation . 23
4.2.1.1 Maximum power and EIRP . 23
4.2.1.2 Combined TX power output and EIRP limits . 23
4.2.1.3 Output power environmental variation. 24
4.2.2 Transmitter power and frequency control . 24
4.2.2.1 Power Control (ATPC and RTPC) . 24
4.2.2.1.0 General background . 24
4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 24
4.2.2.1.2 Remote Transmit Power Control (RTPC) . 24
4.2.2.2 Remote Frequency Control (RFC) . 24
4.2.3 Radio Frequency (RF) spectrum mask. 25
4.2.3.1 Limits background . 25
4.2.3.2 Limits . 28
4.2.4 Discrete CW components exceeding the spectrum mask limit . 41
4.2.4.1 Discrete CW components at the symbol rate . 41
4.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 41
4.2.5 Unwanted emissions in the spurious domain - external . 42
4.2.6 Dynamic Change of Modulation Order . 43
4.2.7 Frequency tolerance . 43
4.2.8 Emission limitations outside the allocated band . 44
4.3 Receiver requirements . 44
4.3.0 General: System loading . 44
4.3.1 Unwanted emissions in the spurious domain - external . 44
4.3.2 BER as a function of receiver input signal level RSL . 44
4.3.3 Receiver selectivity . 45
4.3.3.1 Introduction . 45
4.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 45
ETSI

---------------------- Page: 3 ----------------------
4 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
4.3.3.2.1 Requirements basic . 45
4.3.3.2.2 Limits for co-channel and first adjacent channel . 46
4.3.3.2.3 Limits for second adjacent channel interference . 46
4.3.3.3 CW spurious interference (blocking & spurious response rejection) . 47
4.4 Antenna Characteristics . 48
4.4.1 Integral antennas or dedicated antennas. 48
4.4.1.1 Introduction . 48
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) . 48
4.4.1.3 Antenna gain . 48
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) . 48
4.4.2 Guidelines for stand-alone antennas . 48
5 Testing for compliance with technical requirements . 49
5.1 Environmental and other conditions for testing . 49
5.1.1 Environmental conditions . 49
5.1.2 Other basic conditions . 49
5.2 Test methods for the transmitter . 50
5.2.0 General test summary . 50
5.2.1 Transmitter power and power environmental variation . 51
5.2.1.1 Transmitter power and EIRP . 51
5.2.1.2 Combined TX power output and EIRP limits . 52
5.2.1.3 Output power environmental variation. 52
5.2.2 Transmitter power and frequency control . 52
5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 52
5.2.2.1.1 ATPC . 52
5.2.2.1.2 RTPC . 52
5.2.2.2 Remote Frequency Control (RFC) . 52
5.2.3 RF spectrum mask . 53
5.2.4 Discrete CW components exceeding the spectrum mask limit . 53
5.2.5 Unwanted emissions in the spurious domain - external . 53
5.2.6 Dynamic Change of Modulation Order . 53
5.2.7 Radio frequency tolerance . 54
5.3 Test methods for the receiver . 54
5.3.0 General test summary . 54
5.3.1 Unwanted emissions in the spurious domain - external . 55
5.3.2 BER as a function of receiver input signal level (RSL) . 55
5.3.3 Receiver selectivity . 56
5.3.3.1 Void. 56
5.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 56
5.3.3.2.1 Co-channel and first adjacent channel . 56
5.3.3.2.2 Second adjacent channel . 56
5.3.3.3 CW spurious interference . 56
5.4 Antenna test methods for systems with integral or dedicated antenna . 56
5.4.0 General test summary . 56
5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 57
5.4.2 Antenna gain . 57
5.4.3 Antenna Cross-Polar Discrimination (XPD) . 57
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 58
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz . 60
B.1 Introduction . 60
B.2 General characteristics . 60
B.2.1 Frequency characteristics and channel arrangements . 60
B.2.2 Transmission capacities . 60
B.3 Transmitter . 61
B.3.1 General requirements . 61
B.3.2 RF spectrum masks options . 62
B.4 Receiver . 62
ETSI

---------------------- Page: 4 ----------------------
5 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
B.4.1 General requirements . 62
B.4.2 BER as a function of receiver input signal level (RSL) . 62
B.4.3 Co-channel "external" and adjacent channels interference sensitivity . 63
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz and 56/60 MHz) . 65
C.1 Introduction . 65
C.2 General characteristics . 65
C.2.1 Frequency characteristics and channel arrangements . 65
C.2.2 Transmission capacities . 66
C.3 Transmitter . 67
C.3.1 General requirements . 67
C.3.2 RF spectrum masks . 67
C.4 Receiver . 67
C.4.1 General requirements . 67
C.4.2 BER as a function of Receiver input Signal Level (RSL) . 67
C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 69
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation
40 MHz) . 70
D.1 Introduction . 70
D.2 General characteristics . 70
D.2.1 Frequency characteristics and channel arrangements . 70
D.2.2 Transmission capacities . 70
D.3 Transmitter . 71
D.3.1 General requirements . 71
D.3.2 RF spectrum masks . 71
D.4 Receiver . 72
D.4.1 General requirements . 72
D.4.2 BER as a function of Receiver input Signal Level (RSL) . 72
D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 73
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 74
E.1 Introduction . 74
E.2 General characteristics . 74
E.2.1 Frequency characteristics and channel arrangements . 74
E.2.2 Transmission capacities . 75
E.3 Transmitter . 75
E.3.1 General requirements . 75
E.3.2 RF spectrum masks . 75
E.4 Receiver . 76
E.4.1 General requirements . 76
E.4.2 BER as a function of Receiver input Signal Level (RSL) . 76
E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 79
Annex F (normative): Frequency bands from 23 GHz to 42 GHz . 80
F.1 Introduction . 80
F.2 General characteristics . 80
F.2.1 Frequency characteristics and channel arrangements . 80
F.2.2 Transmission capacities . 81
F.3 Transmitter . 81
F.3.1 General requirements . 81
F.3.2 RF spectrum masks . 82
ETSI

---------------------- Page: 5 ----------------------
6 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
F.4 Receiver . 82
F.4.1 General requirements . 82
F.4.2 BER as a function of Receiver input Signal Level (RSL) . 82
F.4.3 Co-channel "external" and adjacent channel interference sensitivity . 85
Annex G (normative): Frequency bands from 50 GHz to 55 GHz . 86
G.1 Introduction . 86
G.2 General characteristics . 86
G.2.1 Frequency characteristics and channel arrangements . 86
G.2.2 Transmission capacities . 87
G.3 Transmitter . 87
G.3.1 General requirements . 87
G.3.2 RF spectrum masks . 87
G.4 Receiver . 87
G.4.1 General requirements . 87
G.4.2 BER as a function of Receiver input Signal Level (RSL) . 88
G.4.3 Co-channel "external" and adjacent channel interference sensitivity . 88
Annex H (normative): Frequency band 57 GHz to 66 GHz . 89
H.1 Introduction .
...

SLOVENSKI STANDARD
oSIST prEN 302 217-2 V3.2.0:2019
01-maj-2019
)LNVQLUDGLMVNLVLVWHPL.DUDNWHULVWLNHLQ]DKWHYH]DRSUHPRLQDQWHQHWLSDWRþND
WRþNDGHO'LJLWDOQLVLVWHPLNLGHOXMHMRYIUHNYHQþQLKSDVRYLKRG*+]GR
*+]+DUPRQL]LUDQLVWDQGDUG]DGRVWRSGRUDGLMVNHJDVSHNWUD
Fixed Radio Systems - Characteristics and requirements for point-to-point equipment
and antennas - Part 2: Digital systems operating in frequency bands from 1 GHz to 86
GHz - Harmonised Standard for access to radio spectrum
Ta slovenski standard je istoveten z: ETSI EN 302 217-2 V3.2.0 (2019-03)
ICS:
33.060.30 Radiorelejni in fiksni satelitski Radio relay and fixed satellite
komunikacijski sistemi communications systems
33.120.40 Antene Aerials
oSIST prEN 302 217-2 V3.2.0:2019 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

---------------------- Page: 2 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019
Draft ETSI EN 302 217-2 V3.2.0 (2019-03)






HARMONISED EUROPEAN STANDARD
Fixed Radio Systems;
Characteristics and requirements for
point-to-point equipment and antennas;
Part 2: Digital systems operating in frequency bands
from 1 GHz to 86 GHz;
Harmonised Standard for access to radio spectrum

---------------------- Page: 3 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

2 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)



Reference
REN/ATTM-0438
Keywords
antenna, DFRS, digital, DRRS, FWA, point-to-
point, radio, regulation, transmission

ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 4 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

3 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 10
Introduction . 10
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definition of terms, symbols and abbreviations . 15
3.1 Terms . 15
3.2 Symbols . 15
3.3 Abbreviations . 15
4 Technical requirements specifications . 15
4.1 Framework for categorisation of system . 15
4.1.0 Generality . 15
4.1.1 Introduction and equipment flexibility . 15
4.1.2 Operating frequency bands and channel arrangements . 17
4.1.3 Spectral efficiency classes . 17
4.1.4 System alternatives . 18
4.1.5 Channel arrangements and utilization . 18
4.1.6 Specific Requirements for frequency bands . 19
4.1.7 Minimum RIC density for spectral efficiency class selection . 20
4.1.8 Payload flexibility . 20
4.1.9 System identification and traffic loading . 21
4.1.10 Environmental profile . 22
4.2 Transmitter requirements . 22
4.2.0 General: system loading . 22
4.2.1 Transmitter power and power environmental variation . 23
4.2.1.1 Maximum power and EIRP . 23
4.2.1.2 Combined TX power output and EIRP limits . 23
4.2.1.3 Output power environmental variation. 24
4.2.2 Transmitter power and frequency control . 24
4.2.2.1 Power Control (ATPC and RTPC) . 24
4.2.2.1.0 General background . 24
4.2.2.1.1 Automatic Transmit Power Control (ATPC) . 24
4.2.2.1.2 Remote Transmit Power Control (RTPC) . 24
4.2.2.2 Remote Frequency Control (RFC) . 24
4.2.3 Radio Frequency (RF) spectrum mask. 25
4.2.3.1 Limits background . 25
4.2.3.2 Limits . 28
4.2.4 Discrete CW components exceeding the spectrum mask limit . 41
4.2.4.1 Discrete CW components at the symbol rate . 41
4.2.4.2 Other discrete CW components exceeding the spectrum mask limit . 41
4.2.5 Unwanted emissions in the spurious domain - external . 42
4.2.6 Dynamic Change of Modulation Order . 43
4.2.7 Frequency tolerance . 43
4.2.8 Emission limitations outside the allocated band . 44
4.3 Receiver requirements . 44
4.3.0 General: System loading . 44
4.3.1 Unwanted emissions in the spurious domain - external . 44
4.3.2 BER as a function of receiver input signal level RSL . 44
4.3.3 Receiver selectivity . 45
4.3.3.1 Introduction . 45
4.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 45
ETSI

---------------------- Page: 5 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

4 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
4.3.3.2.1 Requirements basic . 45
4.3.3.2.2 Limits for co-channel and first adjacent channel . 46
4.3.3.2.3 Limits for second adjacent channel interference . 46
4.3.3.3 CW spurious interference (blocking & spurious response rejection) . 47
4.4 Antenna Characteristics . 48
4.4.1 Integral antennas or dedicated antennas. 48
4.4.1.1 Introduction . 48
4.4.1.2 Radiation Pattern Envelope (Off-axis EIRP density) . 48
4.4.1.3 Antenna gain . 48
4.4.1.4 Antenna Cross-Polar Discrimination (XPD) . 48
4.4.2 Guidelines for stand-alone antennas . 48
5 Testing for compliance with technical requirements . 49
5.1 Environmental and other conditions for testing . 49
5.1.1 Environmental conditions . 49
5.1.2 Other basic conditions . 49
5.2 Test methods for the transmitter . 50
5.2.0 General test summary . 50
5.2.1 Transmitter power and power environmental variation . 51
5.2.1.1 Transmitter power and EIRP . 51
5.2.1.2 Combined TX power output and EIRP limits . 52
5.2.1.3 Output power environmental variation. 52
5.2.2 Transmitter power and frequency control . 52
5.2.2.1 Transmitter Power Control (ATPC and RTPC) . 52
5.2.2.1.1 ATPC . 52
5.2.2.1.2 RTPC . 52
5.2.2.2 Remote Frequency Control (RFC) . 52
5.2.3 RF spectrum mask . 53
5.2.4 Discrete CW components exceeding the spectrum mask limit . 53
5.2.5 Unwanted emissions in the spurious domain - external . 53
5.2.6 Dynamic Change of Modulation Order . 53
5.2.7 Radio frequency tolerance . 54
5.3 Test methods for the receiver . 54
5.3.0 General test summary . 54
5.3.1 Unwanted emissions in the spurious domain - external . 55
5.3.2 BER as a function of receiver input signal level (RSL) . 55
5.3.3 Receiver selectivity . 56
5.3.3.1 Void. 56
5.3.3.2 Co-channel "external", first and second adjacent channel interference sensitivity . 56
5.3.3.2.1 Co-channel and first adjacent channel . 56
5.3.3.2.2 Second adjacent channel . 56
5.3.3.3 CW spurious interference . 56
5.4 Antenna test methods for systems with integral or dedicated antenna . 56
5.4.0 General test summary . 56
5.4.1 Radiation Pattern Envelope (Off-axis EIRP density) . 57
5.4.2 Antenna gain . 57
5.4.3 Antenna Cross-Polar Discrimination (XPD) . 57
Annex A (informative): Relationship between the present document and the essential
requirements of Directive 2014/53/EU . 58
Annex B (normative): Frequency bands from 1,4 GHz to 2,6 GHz . 60
B.1 Introduction . 60
B.2 General characteristics . 60
B.2.1 Frequency characteristics and channel arrangements . 60
B.2.2 Transmission capacities . 60
B.3 Transmitter . 61
B.3.1 General requirements . 61
B.3.2 RF spectrum masks options . 62
B.4 Receiver . 62
ETSI

---------------------- Page: 6 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

5 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
B.4.1 General requirements . 62
B.4.2 BER as a function of receiver input signal level (RSL) . 62
B.4.3 Co-channel "external" and adjacent channels interference sensitivity . 63
Annex C (normative): Frequency bands from 3,5 GHz to 11 GHz (channel separation up to
30 MHz and 56/60 MHz) . 65
C.1 Introduction . 65
C.2 General characteristics . 65
C.2.1 Frequency characteristics and channel arrangements . 65
C.2.2 Transmission capacities . 66
C.3 Transmitter . 67
C.3.1 General requirements . 67
C.3.2 RF spectrum masks . 67
C.4 Receiver . 67
C.4.1 General requirements . 67
C.4.2 BER as a function of Receiver input Signal Level (RSL) . 67
C.4.3 Co-channel "external" and adjacent channel interference sensitivity . 69
Annex D (normative): Frequency bands from 4 GHz to 11 GHz (channel separation
40 MHz) . 70
D.1 Introduction . 70
D.2 General characteristics . 70
D.2.1 Frequency characteristics and channel arrangements . 70
D.2.2 Transmission capacities . 70
D.3 Transmitter . 71
D.3.1 General requirements . 71
D.3.2 RF spectrum masks . 71
D.4 Receiver . 72
D.4.1 General requirements . 72
D.4.2 BER as a function of Receiver input Signal Level (RSL) . 72
D.4.3 Co-channel "external" and adjacent channel interference sensitivity . 73
Annex E (normative): Frequency bands 13 GHz, 15 GHz and 18 GHz . 74
E.1 Introduction . 74
E.2 General characteristics . 74
E.2.1 Frequency characteristics and channel arrangements . 74
E.2.2 Transmission capacities . 75
E.3 Transmitter . 75
E.3.1 General requirements . 75
E.3.2 RF spectrum masks . 75
E.4 Receiver . 76
E.4.1 General requirements . 76
E.4.2 BER as a function of Receiver input Signal Level (RSL) . 76
E.4.3 Co-channel "external" and adjacent channel interference sensitivity . 79
Annex F (normative): Frequency bands from 23 GHz to 42 GHz . 80
F.1 Introduction . 80
F.2 General characteristics . 80
F.2.1 Frequency characteristics and channel arrangements . 80
F.2.2 Transmission capacities . 81
F.3 Transmitter . 81
F.3.1 General requirements . 81
F.3.2 RF spectrum masks . 82
ETSI

---------------------- Page: 7 ----------------------
oSIST prEN 302 217-2 V3.2.0:2019

6 Draft ETSI EN 302 217-2 V3.2.0 (2019-03)
F.4 Receiver . 82
F.4.1 General requirements . 82
F.4.2 BER as a function of Receiver input Signal Level (RSL) . 82
F.4.3 Co-channel "external" and adjacent channel interference sensitivity . 85
Annex G (normative): Frequency bands from 50 GHz to 55 GHz . 86
G.1 Introduction . 86
G.2 General characteristics . 86
G.2.1 Frequency characteristics and channel arrangements . 86
G.2.2 Transmission capacities . 87
G.3 Transmitter
...