ETSI TR 103 088 V2.1.1 (2019-07)

ETSI TR 103 088 V2.1.1 (2019-07)






TECHNICAL REPORT
Electromagnetic compatibility
and Radio spectrum Matters (ERM);
Using the EN 301 489 series of EMC standards

---------------------- Page: 1 ----------------------
2 ETSI TR 103 088 V2.1.1 (2019-07)



Reference
RTR/ERM-EMC-353
Keywords
EMC, radio
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
The present document can be downloaded from:
http://www.etsi.org/standards-search
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx
If you find errors in the present document, please send your comment to one of the following services:
https://portal.etsi.org/People/CommiteeSupportStaff.aspx
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.

© ETSI 2019.
All rights reserved.

DECT™, PLUGTESTS™, UMTS™ and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.

3GPP™ and LTE™ are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
®
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI

---------------------- Page: 2 ----------------------
3 ETSI TR 103 088 V2.1.1 (2019-07)
Contents
Intellectual Property Rights . 6
Foreword . 6
Modal verbs terminology . 6
Introduction . 6
1 Scope . 7
2 References . 7
2.1 Normative references . 7
2.2 Informative references . 7
3 Definition of terms, symbols and abbreviations . 9
3.1 Terms . 9
3.2 Symbols . 9
3.3 Abbreviations . 9
4 Overview of the ETSI EN 301 489 series . 11
5 Individual parts of the ETSI EN 301 489 series . 11
5.1 ETSI EN 301 489-1 Common technical requirements . 11
5.1.1 Introduction. 11
5.1.2 ETSI EN 301 489-1 V2.1.1 . 11
5.1.3 ETSI EN 301 489-1 V2.2.0 . 12
5.1.4 ETSI EN 301 489-1 V2.2.1 . 12
5.2 ETSI EN 301 489-2 Specific conditions for radio paging equipment . 12
5.2.1 Introduction. 12
5.2.2 ETSI EN 301 489-2 V2.1.1 . 12
5.3 ETSI EN 301 489-3 Specific conditions for Short-Range Devices (SRD) operating on frequencies
between 9 kHz and 246 GHz . 13
5.3.1 Introduction. 13
5.3.2 ETSI EN 301 489-3 V2.1.1 . 13
5.3.3 ETSI EN 301 489-3 V2.2.1 . 13
5.4 ETSI EN 301 489-4 Specific conditions for fixed radio links and ancillary equipment . 13
5.4.1 Introduction. 13
5.4.2 ETSI EN 301 489-4 V3.2.1 . 13
5.4.3 ETSI EN 301 489-4 V3.3.1 . 13
5.5 ETSI EN 301 489-5 Specific conditions for Private land Mobile Radio (PMR) and ancillary equipment
(speech and non-speech) . 14
5.5.1 Introduction. 14
5.5.2 ETSI EN 301 489-5 V2.2.1 . 14
5.6 ETSI EN 301 489-6 Specific conditions for Digital Enhanced Cordless Telecommunications (DECT)
equipment . 14
5.6.1 Introduction. 14
5.6.2 ETSI EN 301 489-6 V2.2.1 . 14
5.7 ETSI EN 301 489-7 Specific conditions for mobile and portable radio and ancillary equipment of digital
cellular radio telecommunications systems (GSM and DCS) . 14
5.8 ETSI EN 301 489-8 Specific conditions for GSM base stations . 15
5.9 ETSI EN 301 489-9 Specific conditions for wireless microphones, similar Radio Frequency (RF) audio
link equipment, cordless audio and in-ear monitoring devices. 15
5.9.1 Introduction. 15
5.9.2 ETSI EN 301 489-9 V2.1.1 . 15
5.10 ETSI EN 301 489-10 Specific conditions for first (CT1 and CT1+) and second generation cordless
telephone (CT2) equipment . 16
5.11 ETSI EN 301 489-11 Specific conditions for terrestrial sound broadcasting service transmitters . 16
5.12 ETSI EN 301 489-12 Specific conditions for Very Small Aperture Terminal, Satellite Interactive Earth
Stations operated in the frequency ranges between 4 GHz and 30 GHz in the Fixed Satellite Service
(FSS) . 16
5.12.1 Introduction. 16
ETSI

---------------------- Page: 3 ----------------------
4 ETSI TR 103 088 V2.1.1 (2019-07)
5.12.2 ETSI EN 301 489-12 V3.1.1. 17
5.13 ETSI EN 301 489-13 Specific conditions for Citizens' Band (CB) radio and ancillary equipment (speech
and non-speech) . 18
5.13.1 Introduction. 18
5.13.2 ETSI EN 301 489-13 V2.1.1. 18
5.14 ETSI EN 301 489-14 Specific conditions for analogue and digital terrestrial TV broadcasting service
transmitters . 18
5.15 ETSI EN 301 489-15 Specific conditions for commercially available amateur radio equipment . 18
5.15.1 Introduction. 18
5.15.2 ETSI EN 301 489-15 V2.2.1. 18
5.16 ETSI EN 301 489-16 Specific conditions for analogue cellular radio communications equipment,
mobile and portable . 18
5.17 ETSI EN 301 489-17 Specific conditions for Broadband Data Transmission Systems . 19
5.17.1 Introduction. 19
5.17.2 ETSI EN 301 489-17 V3.2.1. 19
5.18 ETSI EN 301 489-18 Specific conditions for Terrestrial Trunked Radio (TETRA) equipment . 19
5.19 ETSI EN 301 489-19 Specific conditions for Receive Only Mobile Earth Stations (ROMES) operating
in the 1,5 GHz band providing data communications . 19
5.19.1 Introduction. 19
5.19.2 ETSI EN 301 489-19 V2.1.1. 19
5.19.3 ETSI EN 301 489-19 V2.2.1. 19
5.20 ETSI EN 301 489-20 Specific conditions for Mobile Earth Stations (MES) used in the Mobile Satellite
Services (MSS) . 20
5.20.1 Introduction. 20
5.20.2 ETSI EN 301 489-20 V2.1.1. 20
5.21 ETSI EN 301 489-21 . 20
5.22 ETSI EN 301 489-22 Specific conditions for ground based VHF aeronautical mobile and fixed radio
equipment . 20
5.22.1 Introduction. 20
5.22.2 ETSI EN 301 489-22 V2.1.1. 20
5.23 ETSI EN 301 489-23 Specific conditions for IMT-2000 CDMA, Direct Spread (UTRA and E-UTRA)
Base Station (BS) radio, repeater and ancillary equipment . 21
5.24 ETSI EN 301 489-24 Specific conditions for IMT-2000 CDMA Direct Spread (UTRA and E-UTRA)
for Mobile and portable (UE) radio and ancillary equipment. 21
5.25 ETSI EN 301 489-25 Specific conditions for CDMA 1x spread spectrum Mobile Stations and ancillary
equipment . 21
5.26 ETSI EN 301 489-26 Specific conditions for CDMA 1x spread spectrum Base Stations, repeaters and
ancillary equipment . 22
5.27 ETSI EN 301 489-27 Specific conditions for Ultra Low Power Active Medical Implants (ULP-AMI)
and related peripheral devices (ULP-AMI-P). 22
5.27.1 Introduction. 22
5.27.2 ETSI EN 301 489-27 V2.2.1. 22
5.28 ETSI EN 301 489-28 Specific conditions for wireless digital video links . 23
5.28.1 Introduction. 23
5.28.2 ETSI EN 301 489-28 V2.1.1. 23
5.29 ETSI EN 301 489-29 Specific conditions for Medical Data Service Devices (MEDS) operating in the
401 MHz to 402 MHz and 405 MHz to 406 MHz bands . 23
5.29.1 Introduction. 23
5.29.2 ETSI EN 301 489-29 V2.2.1. 23
5.30 ETSI EN 301 489-30 . 24
5.31 ETSI EN 301 489-31 Specific conditions for equipment in the 9 kHz to 315 kHz band for Ultra Low
Power Active Medical Implants (ULP-AMI) and related peripheral devices (ULP-AMI-P) . 24
5.31.1 Introduction. 24
5.31.2 ETSI EN 301 489-31 V2.2.1. 24
5.32 ETSI EN 301 489-32 Specific conditions for Ground and Wall Probing Radar applications . 24
5.33 ETSI EN 301 489-33 Specific conditions for Ultra Wide Band (UWB) devices . 24
5.33.1 Introduction. 24
5.33.2 ETSI EN 301 489-33 V2.2.1. 25
5.34 ETSI EN 301 489-34 Specific conditions for External Power Supply (EPS) for mobile phones . 25
5.34.1 Introduction. 25
5.34.2 ETSI EN 301 489-34 V2.1.1. 26
ETSI

---------------------- Page: 4 ----------------------
5 ETSI TR 103 088 V2.1.1 (2019-07)
5.35 ETSI EN 301 489-35 Specific requirements for Low Power Active Medical Implants (LP-AMI)
operating in the 2 483,5 MHz to 2 500 MHz bands . 26
5.35.1 Introduction. 26
5.35.2 ETSI EN 301 489-35 V2.2.1. 26
5.36 ETSI EN 301 489-50 Specific conditions for Cellular Communication Base Station (BS), repeater and
ancillary equipment . 26
5.36.1 Introduction. 26
5.36.2 ETSI EN 301 489-50 V2.2.1. 27
5.37 ETSI EN 301 489-51 Specific conditions for Automotive, Ground based Vehicles and Surveillance
Radar Devices using 24,05 GHz to 24,25 GHz, 24,05 GHz to 24,5 GHz, 76 GHz to 77 GHz and 77
GHz to 81 GHz; . 27
5.37.1 Introduction. 27
5.36.2 ETSI EN 301 489-51 V2.2.1. 27
5.38 ETSI EN 301 489-52 Specific conditions for Cellular Communication Mobile and portable radio and
ancillary equipment . 27
5.38.1 Introduction. 27
5.38.2 ETSI EN 301 489-52 V1.1.1. 27
5.39 ETSI EN 301 489-53 Specific conditions for terrestrial sound broadcasting and digital TV broadcasting
service transmitters and associated ancillary equipment . 28
5.39.1 Introduction. 28
5.39.2 ETSI EN 301 489-53 V1.1.1. 28
5.40 ETSI EN 301 489-54 Specific conditions for ground based aeronautical and meteorological radars . 28
5.40.1 Introduction. 28
5.40.2 ETSI EN 301 489-54 V1.1.1. 28
History . 29

ETSI

---------------------- Page: 5 ----------------------
6 ETSI TR 103 088 V2.1.1 (2019-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Report (TR) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio
spectrum Matters (ERM).
Modal verbs terminology
In the present document "should", "should not", "may", "need not", "will", "will not", "can" and "cannot" are to be
interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
Introduction
The ETSI EN 301 489 series [i.2] of EMC standards have been produced by ETSI to enable manufacturers of radio
products to be able to use the harmonised standards route to demonstrate compliance with article 3.1(b) of the Directive
2014/53/EU [i.37] (RE Directive). The present document is designed to assist the manufacturer to apply these standards
in a consistent manner and also understand the various changes between the different versions of each individual part of
the ETSI EN 301 489 series [i.2].
The present document should reduce the number of revisions to the ETSI EN 301 489 series [i.2] of harmonised
standards where these revisions are simply to add new examples of equipment covered into the annex A of the
individual parts.
Earlier editions of the present document, i.e. with version numbers v.1.x.y, relate to previous regulatory regimes,
specifically Directive 1999/5/EC [i.1] (R&TTE Directive).
ETSI

---------------------- Page: 6 ----------------------
7 ETSI TR 103 088 V2.1.1 (2019-07)
1 Scope
The present document is intended to provide guidance on the use of the ETSI EN 301 489 series [i.2] of harmonised
EMC standards produced by ETSI ERM.
Specifically this guidance covers selection of which part that is to be selected for use in conjunction with
ETSI EN 301 489-1 [i.2] to provide the necessary requirements to enable the user to demonstrate compliance with
article 3.1(b) of the Directive 2014/53/EU [i.37] (RE Directive). The aim of this is to increase consistency of
application.
In addition the present document also details the differences between the individual versions of each part of the ETSI
EN 301 489 series [i.2] to assist the reader in reaching a decision on the impact of the different versions on their
particular product.
In the interest of maintaining the document as up to date as possible the present document starts with those versions of
th
the ETSI EN 301 489 series [i.2] cited in the Official Journal of the European Union (OJEU) on the 08 June 2017.
2 References
2.1 Normative references
Normative references are not applicable in the present document.
2.2 Informative references
References are either specific (identified by date of publication and/or edition number or version number) or
non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the
referenced document (including any amendments) applies.
NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee
their long term validity.
The following referenced documents are not necessary for the application of the present document but they assist the
user with regard to a particular subject area.
[i.1] Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio
equipment and telecommunications terminal equipment and the mutual recognition of their
conformity (R&TTE Directive).
[i.2] ETSI EN 301 489 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
ElectroMagnetic Compatibility (EMC) standard for radio equipment and services".
[i.3] Commission Directive 2004/104/EC of 14 October 2004 adapting to technical progress Council
Directive 72/245/EEC relating to the radio interference (electromagnetic compatibility) of vehicles
and amending Directive 70/156/EEC on the approximation of the laws of the Member States
relating to the type-approval of motor vehicles and their trailers.
[i.4] CENELEC EN 55022: "Information technology equipment - Radio disturbance characteristics -
Limits and methods of measurements".
[i.5] ETSI EN 300 676: "ElectroMagnetic Compatibility and Radio Spectrum Matters (ERM); Ground-
based VHF hand-held, mobile and fixed radio transmitters, receivers and transceivers for the VHF
aeronautical mobile service using amplitude modulation; Technical characteristics and methods of
measurement".
[i.6] ETSI TS 125 104: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (FDD) (3GPP TS 25.104)".
ETSI

---------------------- Page: 7 ----------------------
8 ETSI TR 103 088 V2.1.1 (2019-07)
[i.7] ETSI TS 125 105: "Universal Mobile Telecommunications System (UMTS); Base Station (BS)
radio transmission and reception (TDD) (3GPP TS 25.105)".
[i.8] ETSI TS 125 106: "Universal Mobile Telecommunications System (UMTS); UTRA repeater radio
transmission and reception (3GPP TS 25.106)".
[i.9] ETSI TS 136 104: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) radio transmission and reception (3GPP TS 36.104)".
[i.10] ETSI TS 136 141: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station
(BS) conformance testing (3GPP TS 36.141)".
[i.11] ETSI TS 136 106: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater
radio transmission and reception (3GPP TS 36.106)".
[i.12] ETSI TS 136 143: "LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); FDD repeater
conformance testing (3GPP TS 36.143)".
[i.13] ET
...