ETSI EN 300 356-33 V4.1.1 (2003-07)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.SUHVNXãDQMHULWYHIntegrated Services Digital Network (ISDN); Signalling System No.7 (SS7); ISDN User Part (ISUP) version 4 for the international interface; Part 33: Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification for basic services33.080Digitalno omrežje z integriranimi storitvami (ISDN)Integrated Services Digital Network (ISDN)ICS:Ta slovenski standard je istoveten z:EN 300 356-33 Version 4.1.1SIST EN 300 356-33 V4.1.1:2004en01-april-2004SIST EN 300 356-33 V4.1.1:2004SLOVENSKI
STANDARD



SIST EN 300 356-33 V4.1.1:2004



ETSI EN 300 356-33 V4.1.1 (2003-07)European Standard (Telecommunications series) Integrated Service Digital Network (ISDN); Signalling System No.7 (SS7); ISDN User Part (ISUP) version 4 for the international interface; Part 33: Abstract Test Suite (ATS) and partial ProtocolImplementation eXtra Information for Testing (PIXIT)proforma specification for basic services
SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 2
Reference REN/SPAN-130312 Keywords ATS, ISDN, ISUP, PIXIT, SS7, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice Individual copies of the present document can be downloaded from: http://www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http://portal.etsi.org/tb/status/status.asp If you find errors in the present document, send your comment to: editor@etsi.org Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2003. All rights reserved.
DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTM and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 3
Contents Intellectual Property Rights.5 Foreword.5 1 Scope.7 2 References.7 3 Definitions and abbreviations.8 3.1 Definitions.8 3.2 Abbreviations.9 4 Implementation under test and test methods.10 4.1 Identification of the system and Implementation Under Test.10 4.2 ATM and testing configuration for ISUP '92.11 4.2.1 Intermediate exchanges.11 4.2.2 Local exchanges.13 4.2.3 Master-slave aspects in the test configuration.14 5 Conventions used within the ATS.15 5.1 Test suite parameters, constants and variables.15 5.2 Test case variables.15 5.3 ASP constraints.15 5.4 Timers.15 5.5 Test suite operations.15 5.6 Aliases.15 5.7 Test case and step identifiers.16 5.8 Constraints.16 5.9 Dynamic behaviour part.16 5.10 Pre-test conditions.17 6 Test Suite Structure (TSS).18 7 Test Purposes (TP).20 7.1 Introduction.20 7.1.1 Test Purpose (TP) naming convention.20 7.1.2 Source of test purpose definition.21 7.1.3 Test Purpose structure.21 7.2 Test Purposes for the Basic Call.21 7.2.1 CSSV Circuit supervision and signalling supervision.21 7.2.2 NCS Normal call setup ordinary speech calls.47 7.2.3 NCR Normal call release.53 7.2.4 UCS Unsuccessful call setup.54 7.2.5 AS Abnormal situations.55 7.2.6 SCS Special call setup.57 7.2.7 BS Bearer services.62 7.2.8 CUF Congestion and user flow control.67 7.2.9 EC Echo control.68 7.2.10 Temporary Alternate Routing (TAR).73 7.2.11 Hop Counter Procedure (HOP).73 7.2.12 Call Collect Request Procedure (CALLCOL).74 7.2.13 N × 64 kbit/s connection type (N × 64 k).74 8 Test coverage.83 8.1 General remarks.83 9 Conformance to the PICS proforma specification.83 Annex A (informative): Protocol Conformance Test Report (PCTR) Proforma for ISDN User Part (ISUP) v3.84 SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 4
A.1 Identification summary.84 A.1.1 Protocol conformance test report.84 A.1.2 IUT identification.84 A.1.3 Testing environment.84 A.1.4 Limits and reservation.85 A.1.5 Comments.85 A.2 IUT Conformance status.85 A.3 Static conformance summary.85 A.4 Dynamic conformance summary.85 A.5 Static conformance review report.86 A.6 Test campaign report.86 A.7 Observations.95 Annex B (informative): PIXIT proforma for ISDN User Part (ISUP) v3 basic call.96 B.1 Identification summary.96 B.2 Abstract test suite summary.96 B.3 Test laboratory.96 B.4 Client identification.96 B.5 System under test.97 B.6 Ancillary protocols.97 B.7 Protocol information for ISUP.97 B.7.1 Protocol identification.97 B.7.2 IUT information - PIXIT proforma tables.97 B.7.2.1 General configuration.97 B.7.2.2 Parameter values.99 B.7.2.3 Timer values.99 B.7.2.4 Procedural information.100 B.7.2.5 DSS1 call information.100 Annex C (normative): ATS for ISDN User Part (ISUP) v3 basic call control procedures.101 C.1 The TTCN Graphical form (TTCN.GR).101 C.2 The TTCN Machine Processable form (TTCN.MP).101 Annex D (informative): Bibliography.102 History.103
SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 5
Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http://webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This European Standard (Telecommunications series) has been produced by ETSI Technical Committee Services and Protocols for Advanced Networks (SPAN). The present document is part 33 of a multi-part deliverable covering the ISDN User Part (ISUP) version 4 for the international interface, as identified below: Part 1: "Basic services [ITU-T Recommendations Q.761 to Q.764 (1999) modified]"; Part 2: "ISDN supplementary service [ITU-T Recommendation Q.730 (1999) modified]"; Part 3: "Calling Line Identification Presentation (CLIP) supplementary service [ITU-T Recommendation Q.731, clause 3 (1993) modified]"; Part 4: "Calling Line Identification Restriction (CLIR) supplementary service [ITU-T Recommendation Q.731, clause 4 (1993) modified]"; Part 5: "Connected Line Identification Presentation (COLP) supplementary service [ITU-T Recommendation Q.731, clause 5 (1993) modified]"; Part 6: "Connected Line Identification Restriction (COLR) supplementary service [ITU-T Recommendation Q.731, clause 6 (1993) modified]"; Part 7: "Terminal Portability (TP) supplementary service [ITU-T Recommendation Q.733, clause 4 (1993) modified]"; Part 8: "User-to-User Signalling (UUS) supplementary service [ITU-T Recommendation Q.737, clause 1 (1997) modified]"; Part 9: "Closed User Group (CUG) supplementary service [ITU-T Recommendation Q.735, clause 1 (1993) modified]"; Part 10: "Subaddressing (SUB) supplementary service [ITU-T Recommendation Q.731, clause 8 (1992) modified]"; Part 11: "Malicious Call Identification (MCID) supplementary service [ITU-T Recommendation Q.731, clause 7 (1997) modified]"; Part 12: "Conference call, add-on (CONF) supplementary service [ITU-T Recommendation Q.734, clause 1 (1993) and implementors guide (1998) modified]"; Part 14: "Explicit Call Transfer (ECT) supplementary service [ITU-T Recommendation Q.732, clause 7 (1996) and implementors guide (1998) modified]"; Part 15: "Diversion supplementary service [ITU-T Recommendation Q.732, clauses 2 to 5 (1999) modified]"; Part 16: "Call Hold (HOLD) supplementary service [ITU-T Recommendation Q.733, clause 2 (1993) modified]"; Part 17: "Call Waiting (CW) supplementary service [ITU-T Recommendation Q.733, clause 1 (1992) modified]"; SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 6
Part 18: "Completion of Calls to Busy Subscriber (CCBS) supplementary service [ITU-T Recommendation Q.733, clause 3 (1997) modified]"; Part 19: "Three-Party (3PTY) supplementary service [ITU-T Recommendation Q.734, clause 2 (1996) and implementors guide (1998) modified]"; Part 20: "Completion of Calls on No Reply (CCNR) supplementary service [ITU-T recommendation Q.733, clause 5 (1999) modified]"; Part 21: "Anonymous Call Rejection (ACR) supplementary service [ITU-T Recommendation Q.731, clause 4 (1993)]"; Part 22: "International Emergency Preference Scheme (IEPS) service [ITU-T Amendments (2002) to
Q.761 - Q.764 (1999) modified]"; Part 31: "Protocol Implementation Conformance Statement (PICS) proforma specification for basic services"; Part 32: "Test Suite Structure and Test Purposes (TSS&TP) specification for basic services"; Part 33: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification for basic services"; Part 34: "Protocol Implementation Conformance Statement (PICS) proforma specification for supplementary services"; Part 35: "Test Suite Structure and Test Purposes (TSS&TP) specification for supplementary services"; Part 36: "Abstract Test Suite (ATS) and partial Protocol Implementation eXtra Information for Testing (PIXIT) proforma specification for supplementary services". NOTE: Parts 13 and 23 to 30 have not been issued.
National transposition dates Date of adoption of this EN: 27 June 2003 Date of latest announcement of this EN (doa): 30 September 2003 Date of latest publication of new National Standard or endorsement of this EN (dop/e):
31 March 2004 Date of withdrawal of any conflicting National Standard (dow): 31 March 2004
SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 7
1 Scope The present document contains the validation (conformance) test specification for ISUP v4 basic call control and signalling procedures defined in ITU-T Recommendation Q.764 [13] as endorsed by EN 300 356-1 [1]. The present document applies only to exchanges having implemented the ISUP v4 protocol specification. It is applicable for validation testing of all types of exchanges as defined in the ISUP v4 protocol specification. NOTE: The compatibility tests are covered by ITU-T Recommendation Q.784.1 [9]. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. • References are either specific (identified by date of publication and/or edition number or version number) or non-specific. • For a specific reference, subsequent revisions do not apply. • For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http://docbox.etsi.org/Reference. [1] ETSI EN 300 356-1 (V3.2.2): "Integrated Services Digital Network (ISDN); Signalling System No.7; ISDN User Part (ISUP) version 3 for the international interface; Part 1: Basic services [ITU-T Recommendations Q.761 to Q.764 (1997), modified]". [2] ISO/IEC 9646-1 (1994): "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts". [3] ISO/IEC 9646-3: "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)". [4] ISO/IEC 9646-5 (1994): "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 5: Requirements on test laboratories and clients for the conformance assessment process". [5] ISO/IEC 9646-7: "Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance Statements". [6] ITU-T Recommendation E.164 (1997): "The international public telecommunication numbering plan". [7] ITU-T Recommendation Q.701 (1993): "Functional description of the message transfer part (MTP) of Signalling System No. 7". [8] ITU-T Recommendation Q.707 (1988): "Testing and maintenance". [9] ITU-T Recommendation Q.784.1 (1996): "Validation and compatibility for ISUP'92 and Q.767 protocols". [10] ITU-T Recommendation Q.784.2 (1997): "Abstract test suite for ISUP'92 basic call control procedures". [11] ITU-T Recommendation Q.784.3 (1999): "ISUP '97 basic call control procedures - Test suite structure and test purposes (TSS&TP)". [12] ITU-T Recommendation Q.761 (1997): "Signalling System No. 7 - ISDN User Part functional description". SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 8
[13] ITU-T Recommendation Q.764 (1997): "Signalling System No. 7 - ISDN user part signalling procedures". [14] ITU-T Recommendation Q.730: "ISDN user part supplementary services". [15] ITU-T Recommendation Q.731: "Stage 3 description for number identification supplementary services using Signalling System No. 7". [16] ITU-T Recommendation Q.733: "Stage 3 description for call completion supplementary services using Signalling System No. 7". [17] ITU-T Recommendation Q.737: "Stage 3 description for additional information transfer supplementary services using Signalling System No. 7". [18] ITU-T Recommendation Q.735: "Stage 3 description for community of interest supplementary services using Signalling System No. 7". [19] ITU-T Recommendation Q.734 (1993): "Stage 3 description for multiparty supplementary services using Signalling System No. 7". [20] ITU-T Recommendation Q.732: "Stage 3 description for call offering supplementary services using Signalling System No. 7". [21] ITU-T Recommendation Q.762 (1997): "Signalling System No. 7 - ISDN User Part general functions of messages and signals". [22] ITU-T Recommendation Q.763 (1997): "Signalling System No. 7 - ISDN User Part formats and codes". [23] ITU-T Recommendation Q.767 (1991): "Application of the ISDN user part of CCITT signalling system No. 7 for international ISDN interconnections". [24] ITU-T Recommendation Q.724 (1988): "Telephone user part signalling procedures". 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: • terms defined in ISDN User Part (ISUP) reference specification ITU-T Recommendations Q.761 [12], Q.762 [21], Q.763 [22] and Q.764 [13] as endorsed by EN 300 356-1 [1]; • terms defined in ISO/IEC 9646-1 [2], ISO/IEC 9646-3 [3] and in ISO/IEC 9646-7 [5]. In particular, the following terms apply: Abstract Test Case (ATC): complete and independent specification of the actions required to achieve a specific test purpose, defined at the level of abstraction of a particular Abstract Test Method, starting in a stable testing state and ending in a stable testing state (see ISO/IEC 9646-1, clause 3.3.3) Abstract Test Method (ATM): description of how an IUT is to be tested, given at an appropriate level of abstraction to make the description independent of any particular realization of a Means of Testing, but with enough detail to enable abstract test cases to be specified for this method (see ISO/IEC 9646-1, clause 3.3.5) Abstract Test Suite (ATS): test suite composed of abstract test cases (see ISO/IEC 9646-1, clause 3.3.6) Implementation Under Test (IUT): implementation of one or more OSI protocols in an adjacent user/provider relationship, being part of a real open system which is to be studied by testing (see ISO/IEC 9646-1, clause 3.3.43) ISDN number: number conforming to the numbering and structure specified in ITU-T Recommendation E.164 SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 9
Means of Testing (MOT): combination of equipment and procedures that can perform the derivation, selection, parameterization and execution of test cases, in conformance with a reference standardized ATS, and can produce a conformance log (see ISO/IEC 9646-1, clause 3.3.54) Point of Control and Observation (PCO): point within a testing environment where the occurrence of test events is to be controlled and observed, as defined in an Abstract Test Method (see ISO/IEC 9646-1, clause 3.3.64) pre-test condition: setting or state in the IUT which cannot be achieved by providing stimulus from the test environment Protocol Implementation Conformance Statement (PICS): statement made by the supplier of a protocol claimed to conform to a given specification, stating which capabilities have been implemented (see ISO/IEC 9646-1, clause 3.3.39 and clause 3.3.80) PICS proforma: document, in the form of a questionnaire, which when completed for an implementation or system becomes the PICS Protocol Implementation eXtra Information for Testing (PIXIT): statement made by a supplier or implementor of an IUT (protocol) which contains or references all of the information related to the IUT and its testing environment, which will enable the test laboratory to run an appropriate test suite against the IUT (see ISO/IEC 9646-1, clause 3.3.41 and clause 3.3.81) PIXIT proforma: document, in the form of a questionnaire, which when completed for the IUT becomes the PIXIT System Under Test (SUT): real open system in which the IUT resides (see ISO/IEC 9646-1, clause 3.3.103) user: access protocol entity at the User side of the user-network interface where a T reference point or coincident S and T reference point applies 3.2 Abbreviations The ISUP message acronyms can be found in table 2 of ITU-T Recommendation Q.762 [21] as endorsed by EN 300 356-1 [1]. For the purposes of the present document, the following abbreviations apply: ACH Access signalling PCO - (D-channel) APH Access physical circuit PCO - (B-channel) ASP Abstract Service Primitive ATC Abstract Test Case ATM Abstract Test Method ATS Abstract Test Suite CAB PCO for AB circuits CAC PCO for AC circuits CIC Circuit Identification Code DLE Destination Local Exchange DSS1 Digital Subscriber System No. one IncIE Incoming International Exchange ISDN Integrated Services Digital Network ISUP ISDN User Part
ITE International Transit Exchange IUT Implementation Under Test LAB PCO for signalling link AB LAC PCO for signalling link AC LT Lower Tester MMI Man Machine Interface MNT Maintenance PCO MOT Means Of Testing MTC Main Test Component NTE National Transit Exchange OLE Originating Local Exchange OPR Operator PCO OutIE Outgoing International Exchange SIST EN 300 356-33 V4.1.1:2004



ETSI ETSI EN 300 356-33 V4.1.1 (2003-07) 10 PCO Point of Control and Observation PCTR Protocol Conformance Test Report PICS Protocol Implementation Conformance Statement PIXIT Protocol Implementation eXtra Information for Testing PTC Parallel Test Component SCS System Conformance Statement SP Signalling Point SUT System Under Test TCP Test Coordination Procedures TP Test Purpose TSS Test Suite Structure TSS&TP Test Suite Structure and Test Purposes TTCN Tree and Tabular Combined Notation UNI User-Network Interface UT Upper Tester 4 Implementation under test and test methods 4.1 Identification of the system and Implementation Under Test The System Under Test (SUT) is an exchange. SUT Exchange MMI capabilities and functions ISUP Access ISUP ISUP '92 IUT
Figure 1/ITU-T Recommendation Q.784.2 [10]: Exchange as SUT The Implementation Under Test (IUT) is the ISUP '97 implementation in this exchange, as shown in figure 1/ITU-T Recommendat
...