ETSI EN 300 390 V2.1.1 (2016-03)

2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.UPRQL]LUDQL(8Land Mobile Service - Radio equipment intended for the transmission of data (and speech) and using an integral antenna - Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU33.070.01Mobilni servisi na splošnoMobile services in general33.060.99Druga oprema za radijske komunikacijeOther equipment for radiocommunicationsICS:Ta slovenski standard je istoveten z:ETSI EN 300 390 V2.1.1 (2016-03)SIST EN 300 390 V2.1.1:2016en01-junij-2016SIST EN 300 390 V2.1.1:2016SLOVENSKI
STANDARD



SIST EN 300 390 V2.1.1:2016



ETSI EN 300 390 V2.1.1 (2016-03) Land Mobile Service; Radio equipment intended for the transmission of data (and speech) and using an integral antenna; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 390 V2.1.1:2016



ETSI ETSI EN 300 390 V2.1.1 (2016-03) 2
Reference REN/ERM-TGDMR-347 Keywords antenna, data, mobile, PMR, radio, speech, transmission ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: http://www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https://portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https://portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 390 V2.1.1:2016



ETSI ETSI EN 300 390 V2.1.1 (2016-03) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 7 1 Scope . 8 2 References . 8 2.1 Normative references . 8 2.2 Informative references . 9 3 Definitions, symbols and abbreviations . 9 3.1 Definitions . 9 3.2 Symbols . 11 3.3 Abbreviations . 11 4 General and operational requirements . 11 4.1 General . 11 4.1.1 Environmental profile . 11 4.1.2 Choice of model for testing . 11 4.1.2.0 General . 11 4.1.2.1 Auxiliary test equipment . 12 4.1.2.2 Declarations by the supplier . 12 4.2 Mechanical and electrical design . 12 4.2.1 General . 12 4.2.2 Controls . 12 4.2.3 Transmitter shut-off facility . 12 4.3 Marking . 12 4.4 Testing using bit streams or messages . 12 4.5 Measuring continuous mode equipment . 12 4.6 Measuring discontinuous mode equipment . 12 4.7 Constant and non-constant envelope modulation . 13 4.8 Combined full bandwidth analogue speech/full bandwidth digital equipment . 13 5 Test conditions, power sources and ambient temperatures . 14 5.1 Normal and extreme test conditions . 14 5.2 Test power source . 14 5.3 Normal test conditions . 14 5.3.1 Normal temperature and humidity . 14 5.3.2 Normal test power source . 14 5.3.2.1 Mains voltage . 14 5.3.2.2 Regulated lead-acid battery power sources used on vehicles . 15 5.3.2.3 Other power sources . 15 5.4 Extreme test conditions . 15 5.4.1 Extreme temperatures . 15 5.4.2 Extreme test source voltages . 15 5.4.2.1 Mains voltage . 15 5.4.2.2 Regulated lead-acid battery power sources used on vehicles . 15 5.4.2.3 Power sources using other types of batteries . 15 5.4.2.4 Other power sources . 15 5.5 Procedure for tests at extreme temperatures . 16 5.5.0 Thermal balance . 16 5.5.1 Procedure for equipment designed for continuous transmission. 16 5.5.2 Procedure for equipment designed for intermittent transmission . 16 6 General conditions of measurement . 16 6.1 Normal test signals (wanted and unwanted signals) . 16 6.1.0 General . 16 6.1.1 Signals for bit stream measurements . 16 6.1.2 Signals for messages . 17 6.2 Artificial antenna . 17 SIST EN 300 390 V2.1.1:2016



ETSI ETSI EN 300 390 V2.1.1 (2016-03) 4 6.3 Test sites and general arrangements for radiated measurements . 17 6.4 Transmitter automatic shut-off facility . 17 6.5 Modes of operation of the transmitter . 18 6.6 Encoder for receiver measurements . 18 6.7 Transceiver data interface. 18 6.8 Arrangements for test signals at the input of the receiver via a test fixture or a test antenna . 18 6.9 Facilities for access . 18 6.9.1 Analogue access . 18 6.9.2 Points for bit stream measurement . 18 6.9.3 Coupling arrangements . 19 6.9.3.0 General . 19 6.9.3.1 Arrangements for measurements with continuous bit streams . 19 6.9.3.2 Arrangements for measurements with messages . 19 6.10 Receiver mute or squelch facility . 19 7 Technical characteristics of the transmitter . 19 7.0 General . 19 7.1 Frequency error . 19 7.1.0 General . 19 7.1.1 Definition . 20 7.1.2 Method of measurement . 20 7.1.3 Limits . 20 7.2 Effective radiated power . 20 7.2.0 General . 20 7.2.1 Definition . 21 7.2.2 Method of measurement . 21 7.2.2.0 General . 21 7.2.2.1 Maximum effective radiated power under normal test conditions . 21 7.2.2.2 Average effective radiated power under normal test conditions . 23 7.2.2.3 Method of measurements of maximum and average effective radiated power under extreme test conditions . 23 7.2.3 Limits . 23 7.2.3.1 Effective radiated power under normal test conditions . 23 7.2.3.2 Effective radiated power under extreme test conditions . 24 7.3 Adjacent and alternate channel power . 24 7.3.0 General . 24 7.3.1 Definition . 24 7.3.2 Method of measurement . 24 7.3.3 Limits . 26 7.4 Radiated unwanted emissions in the spurious domain . 26 7.4.0 General . 26 7.4.1 Definition . 26 7.4.2 Method of measurement . 27 7.4.3 Limits . 29 7.5 Transmitter attack time . 29 7.5.0 General . 29 7.5.1 Definition . 29 7.5.2 Method of measurement . 29 7.5.3 Limits . 30 7.6 Transmitter release time . 30 7.6.0 General . 30 7.6.1 Definition . 30 7.6.2 Method of measurement . 30 7.6.3 Limits . 31 7.7 Transient behaviour of the transmitter . 31 7.7.0 General . 31 7.7.1 Definitions . 31 7.7.2 Timings, frequencies and powers . 32 7.7.3 Methods of measurement . 36 7.7.3.0 General . 36 7.7.3.1 Time and frequency domain analysis measurements . 36 7.7.3.2 Test arrangement and characteristics of the test discriminator . 37 SIST EN 300 390 V2.1.1:2016



ETSI ETSI EN 300 390 V2.1.1 (2016-03) 5 7.7.3.3 Adjacent channel transient power measurements . 37 7.7.3.4 Characteristics of the adjacent channel transient power measuring device . 38 7.7.4 Limits . 38 7.7.4.1 Time domain analysis of power and frequency . 38 7.7.4.2 Adjacent channel transient power . 39 8 Technical characteristics of the receiver . 39 8.1 Average usable sensitivity (field strength, data or messages) . 39 8.1.1 Definition . 39 8.1.2 Method of measurement with continuous bit streams under normal test conditions . 39 8.1.3 Method of measurement with continuous bits streams under extreme test conditions . 41 8.1.4 Method of measurement with messages under normal test conditions . 41 8.1.5 Method of measurement with messages under extreme test conditions. 43 8.1.6 Reference for degradation measurements . 44 8.1.6.1 Definition . 44 8.1.6.2 Procedures for measurements using the test fixture . 44 8.1.6.3 Procedures for measurements on a test site . 44 8.1.7 Limits . 44 8.2 Error behaviour at high input levels . 45 8.2.1 Definition . 45 8.2.2 Method of measurement with continuous bit streams . 46 8.2.3 Method of measurement with messages . 46 8.2.4 Limits . 46 8.3 Co-channel rejection. 47 8.3.1 Definition . 47 8.3.2 Method of measurement with continuous bit streams . 47 8.3.3 Method of measurement with messages . 48 8.3.4 Limits . 49 8.4 Adjacent channel selectivity . 49 8.4.1 Definition . 49 8.4.2 Method of measurement with continuous bit streams . 49 8.4.3 Method of measurement with messages . 50 8.4.4 Limits . 51 8.5 Spurious response rejection . 51 8.5.0 General . 51 8.5.1 Definition . 52 8.5.2 Introduction to the method of measurement . 52 8.5.3 Measurement arrangement . 53 8.5.4 Method of the search over the limited frequency range with continuous bit streams . 54 8.5.5 Method of the search over the limited frequency range with messages . 54 8.5.6 Method of measurement with continuous bit streams . 55 8.5.7 Method of measurement with messages . 56 8.5.8 Limits . 57 8.6 Intermodulation response rejection . 57 8.6.0 General . 57 8.6.1 Definition . 57 8.6.2 Method of measurement with continuous bit streams . 57 8.6.3 Method of measurement with messages . 58 8.6.4 Limits . 59 8.7 Blocking or desensitization . 59 8.7.0 General . 59 8.7.1 Definition . 59 8.7.2 Method of measurement with continuous bit streams . 60 8.7.3 Method of measurement with messages . 61 8.7.4 Limits . 62 8.8 Spurious radiations . 62 8.8.0 General .
...