ETSI EN 302 842-3 V1.2.1 (2006-12)

SLOVENSKI STANDARD
SIST EN 302 842-3 V1.2.1:2007
01-marec-2007
(OHNWURPDJQHWQD]GUXåOMLYRVWLQ]DGHYHY]YH]L]UDGLMVNLPVSHNWURP(50
]UDNQDþLQ5DGLMVNDRSUHPD]DGLJLWDOQRSRYH]DYR9+)9'/]UDNWODLQ]UDN
7HKQLþQHNDUDNWHULVWLNHLQPHULOQHPHWRGH]DDHURQDYWLþQRPRELOQROHWDOVNR
RSUHPRGHO'RGDWQLYLGLNLY]YH]L]UDGLRGLIX]LMR
Electromagnetic compatibility and Radio spectrum Matters (ERM); VHF air-ground and
air-air Digital Link (VDL) Mode 4 radio equipment; Technical characteristics and methods
of measurement for aeronautical mobile (airborne) equipment; Part 3: Additional
broadcast aspects
Ta slovenski standard je istoveten z: EN 302 842-3 Version 1.2.1
ICS:
33.060.99 Druga oprema za radijske Other equipment for
komunikacije radiocommunications
33.100.01 Elektromagnetna združljivost Electromagnetic compatibility
na splošno in general
49.090 2SUHPDLQLQVWUXPHQWLY On-board equipment and
]UDþQLKLQYHVROMVNLKSORYLOLK instruments
SIST EN 302 842-3 V1.2.1:2007 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 302 842-3 V1.2.1:2007

---------------------- Page: 2 ----------------------

SIST EN 302 842-3 V1.2.1:2007

ETSI EN 302 842-3 V1.2.1 (2006-12)
European Standard (Telecommunications series)

Electromagnetic compatibility
and Radio spectrum Matters (ERM);
VHF air-ground and air-air Digital Link (VDL)
Mode 4 radio equipment;
Technical characteristics and
methods of measurement
for aeronautical mobile (airborne) equipment;
Part 3: Additional broadcast aspects

---------------------- Page: 3 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 2 ETSI EN 302 842-3 V1.2.1 (2006-12)



Reference
REN/ERM-TG25-030-3
Keywords
aeronautical, digital, radio, testing, VHF
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, please send your comment to one of the following services:
http://portal.etsi.org/chaircor/ETSI_support.asp
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2006.
All rights reserved.

TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI

---------------------- Page: 4 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 3 ETSI EN 302 842-3 V1.2.1 (2006-12)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .6
1 Scope.7
2 References.8
3 Definitions and abbreviations.9
3.1 Definitions.9
3.1.1 Basic reference model definitions.9
3.1.2 Service conventions definitions .9
3.1.3 General definitions.9
3.1.4 Definition of bit order.10
3.2 Abbreviations.10
4 General description of VDL Mode 4 broadcast services.11
4.1 General.11
4.2 Automatic Dependent Surveillance-Broadcast (ADS-B) .12
4.3 Traffic Information Service-Broadcast (TIS-B) .13
4.4 Flight Information Service-Broadcast (FIS-B).13
4.5 GNSS Augmentation Service-Broadcast (GNS-B) .14
5 Minimum performance specification under standard test conditions.15
5.1 Requirements for ADS-B.15
5.1.1 Information Field Formats .15
5.1.2 ADS-B Request.25
5.1.2.1 ADS-B request format.25
5.1.2.2 Sleep Mode.26
5.1.2.3 Automatic Selection of Variable Information Fields .26
5.1.3 Default ADS-B Reporting.28
5.1.4 ADS-B Procedures.28
5.1.5 CTRL Parameters.30
5.1.5.1 Directory of Service (DOS) message .30
5.1.5.2 Channel Management Parameter .31
5.1.6 Definitions for Compact Position Reporting .42
5.1.6.1 Information Field Offset Encoding .42
5.1.6.2 Information Field Offset Decoding .44
5.1.6.3 Patch ID Encoding .45
5.1.6.4 Patch Id Decoding.46
5.1.7 Encoding of UDATA (udid) .46
5.2 Requirements for TIS-B .47
5.2.1 Traffic Information Volume (TIV) .47
5.2.2 Void.47
5.2.3 Message format.47
5.2.4 Management message.48
5.2.5 Aircraft target messages (airborne TIV) .50
5.2.6 Aircraft target messages (ground TIV) .52
5.2.7 Ground vehicle target messages (ground TIV) .54
5.2.8 TIS-B offset encoding.54
5.3 Requirements for FIS-B .57
5.3.1 Message format for received FIS-B messages.57
5.3.2 Meteorological Aerodrome Report (METAR) message .58
5.3.3 Special Observations and Reports (SPECI) message.65
5.3.4 Automatic Terminal Information Service (ATIS) message .66
5.3.5 Runway Condition (RCN) message.68
5.3.6 SIGnificant METeorological Information (SIGMET) message.72
5.3.7 Temporary Segregated Areas (TSA) message .73
ETSI

---------------------- Page: 5 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 4 ETSI EN 302 842-3 V1.2.1 (2006-12)
5.3.8 FIS-B report request message .76
5.3.9 Void.77
5.3.9a Airborne system functions.77
5.3.9a.1 Transmission of requests.77
5.3.9a.2 Differentiation between reports.77
5.4 Requirements for GNSS Augmentation Service Broadcast (GNS-B) message .78
5.4.1 Message format.78
5.4.2 Message Type 1 .79
5.4.3 Message Type 2 .82
5.4.4 Message Type 4 .86
5.4.5 CRC Calculation.92
5.4.5.1 GNS-B CRC.92
5.4.5.2 FAS CRC.92
5.4.5.3 Ephemeris CRC.93
6 General design requirements.93
7 Protocol test procedures.93
7.1 General.93
7.2 Required test rig .94
7.3 Protocol test-suite description methodology .94
7.4 Detailed protocol test procedures .94
7.4.1 Test-suite overview.94
7.4.2 Declarations.97
7.4.3 Constraints.98
7.4.3.1 Abbreviations.98
7.4.3.1.1 Subfield mnemonics.98
7.4.3.1.2 Station addresses and positions .101
7.4.3.1.3 Tables of values for use in CPR test cases .102
7.4.3.1.4 Tables of values for use in content checking test cases .112
7.4.3.1.5 VDL4 Burst formats.146
7.4.3.2 Test cases.185
7.4.3.2.1 Test case macros.186
7.4.3.2.2 Test case descriptions .187
Annex A (informative): Cross reference matrix .267
Annex B (informative): Bibliography.279
History .286

ETSI

---------------------- Page: 6 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 5 ETSI EN 302 842-3 V1.2.1 (2006-12)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This European Standard (Telecommunications series) has been produced by ETSI Technical Committee
Electromagnetic compatibility and Radio spectrum Matters (ERM).
The present document is part 3 of a multi-part deliverable covering the VHF air-ground and air-air Digital Link (VDL)
Mode 4 radio equipment; Technical characteristics and methods of measurement for aeronautical mobile (airborne)
equipment, as identified below:
Part 1: "Physical layer";
Part 2: "General description and data link layer";
Part 3: "Additional broadcast aspects";
Part 4: "Point-to-point functions";
Part 5: "VDL4 airbone equipment in compliance with the SES 552/2004 interoperability Regulation".
The present document is accompanied by an equivalent ground-based standard, EN 301 842 [9] parts 1 to 4, covering
the VHF air-ground Data Link (VDL) Mode 4 radio equipment; Technical characteristics and methods of measurement
for ground-based equipment.
NOTE: Minimum Operational Performance Specifications (MOPS) are also being developed for VDL Mode 4.
EUROCAE have previously published Interim MOPS for VDL Mode 4 (see bibliography) which are a
sub set of EN 302 842-1 [4], 2 [5], 3 (the present document) and 4 [6]. EN 302 842-1 [4], 2 [5], 3 (the
present document) and 4 [6] comply with the requirements of CEC Mandate M/318.

National transposition dates
Date of adoption of this EN: 24 November 2006
Date of latest announcement of this EN (doa): 28 February 2007
Date of latest publication of new National Standard
or endorsement of this EN (dop/e): 31 August 2007
Date of withdrawal of any conflicting National Standard (dow): 31 August 2007

ETSI

---------------------- Page: 7 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 6 ETSI EN 302 842-3 V1.2.1 (2006-12)
Introduction
The present document states the technical specifications for Very High Frequency (VHF) Digital Link (VDL) Mode 4
aeronautical mobile (airborne) radio transmitters, transceivers and receivers for air-ground and air-air communications
operating in the VHF band, using Gaussian Filtered Frequency Shift Keying (GFSK) modulation with 25 kHz channel
spacing and capable of tuning to any of the 25 kHz channels from 118,000 MHz to 136,975 MHz as defined in
ICAO VDL SARPs [2].
The present document may be used to produce tests for the assessment of the performance of the equipment. The
performance of the equipment submitted for type testing should be representative of the performance of the
corresponding production model.
The present document has been written on the assumption that:
• the type test measurements will be performed only once, in an accredited test laboratory and the measurements
accepted by the various authorities in order to grant type approval;
• if equipment available on the market is required to be checked it will be tested in accordance with the methods
of measurement specified in the present document or a documented alternative approved by the certifying
authority;
• equipment comply with EN 302 842-1 [4] and EN 302 842-2 [5].
The present document also indicates VDL Mode 4 compliance with the SES 552/2004 interoperability Regulation [10].
NOTE: The present document has been produced with a view to maintaining consistency of numbering with the
equivalent standard for ground equipment (EN 301 842 all parts [9]). Where requirements are the same,
they have been given the same number. Some new airborne requirements have been inserted between
requirements that were sequential in EN 301 842 [9]. This has led to a non-standard form of numbering
for new requirements in some places.
ETSI

---------------------- Page: 8 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 7 ETSI EN 302 842-3 V1.2.1 (2006-12)
1 Scope
The present document applies to the following radio equipment types:
• Very High Frequency (VHF) Digital Link (VDL) Mode 4 aeronautical mobile (airborne) radio transmitters,
transceivers and receivers for air-ground and air-air communications operating in the VHF band, using
Gaussian Filtered Frequency Shift Keying (GFSK) modulation with 25 kHz channel spacing and capable of
tuning to any of the 25 kHz channels from 118,000 MHz to 136,975 MHz as defined in ICAO VDL
SARPs 130 [2].
The present technical document provides part 3 of the technical specifications.
The present document is designed to ensure that equipment certified to it will be compatible with the relevant
ICAO VDL SARPs [2] and ICAO VDL4 Technical Manual [1] and with the SES 552/2004 interoperability
Regulation [10].
Manufacturers should note that in future the tuning range for the transmitter may also cover any 25 kHz channel from
112,000 MHz to 117,975 MHz and the receiver(s) may cover any 25 kHz channel from 108,000 MHz to 117,975 MHz.
The present document applies to "aeronautical mobile (airborne and in some cases ground vehicles)" equipment which
will hereinafter be referred to as "mobile" equipment.
The scope of the present document is limited to mobile stations. The equivalent specification for ground stations is
EN 301 842 [9].
A description of the scope of the VDL Mode 4 system is provided in part 2 of these technical specifications
(see EN 302 842-2 [5] clause 1).
EN 302 842-1 [4] deals with tests of the physical layer. EN 302 842-2 [5] deals with tests of the link layer sufficient to
support broadcast functionality including requirements and tests sufficient to recognize and respond to transmissions
associated with point-to-point communication. The present document provides technical specifications for a VDL
Mode 4 mobile transceiver supporting a full Automatic Dependent Surveillance-Broadcast (ADS-B) capability and,
optionally, the additional functionality of either, or a combination of, the following services:
• Traffic Information Service-Broadcast (TIS-B);
• Flight Information Service-Broadcast (FIS-B);
• GNSS Augmentation Service-Broadcast (GNS-B).
The TIS-B, FIS-B, or GNS-B reception processing functionality in the airborne equipment is expected to be provided
by a TIS-B, FIS-B or GNS-B processor, which could be contained within the VDL Mode 4 transceiver, but could also
be housed in a separate physical unit. Therefore to support TIS-B, FIS-B or GNS-B message reception, the minimum
functionality demanded of a basic VDL Mode 4 airborne transceiver unit (i.e. one that does not have a TIS-B, FIS-B or
GNS-B processor housed within it) is to pass to the TIS-B, FIS-B or GNS-B processor, all TIS-B, FIS-B or GNS-B
messages received.
As the measured values of equipment performance may be a function of the method of measurement, standard test
conditions and methods of test are recommended in the present document.
The present document is organized as follows:
• clause 2 provides references to relevant documents;
• clause 3 provides general definitions, abbreviations and symbols used;
• clause 4 describes the VDL Mode 4 mobile station functionality to support ADS-B, TIS-B, FIS-B and GNS-B;
• clause 5 provides performance specifications for the VDL Mode 4 mobile station supporting ADS-B, TIS-B,
FIS-B and GNS-B Services;
• clause 6 provides general design requirements;
ETSI

---------------------- Page: 9 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 8 ETSI EN 302 842-3 V1.2.1 (2006-12)
• clause 7 provides protocol tests which emphasis the ADS-B, TIS-B, FIS-B and GNS-B functions of the
system;
• annex A provides a detailed cross-reference to the relevant requirements contained in
ICAO VDL4 Technical Manual [1];
• annex B provides a Bibliography;
• a document history.
Note that the system can support a very wide range of functions. It is not practical to provide specific tests for all
aspects of functionality. The approach used is to provide detailed tests for the core functionality to support ADS-B,
FIS-B, TIS-B and GNS-B focusing on the system requirements which, if wrongly implemented, could cause a
deterioration in the service offered by other VDL Mode 4 stations.
Mandating and Recommendation Phrases
a) "Shall":
- The use of the word "Shall" indicates a mandated criterion; i.e. compliance with the particular procedure
or specification is mandatory and no alternative may be applied.
b) "Should":
- The use of the word "Should" (and phrases such as "It is recommended that.", etc.) indicates that though
the procedure or criterion is regarded as the preferred option, alternative procedures, specifications or
criteria may be applied, provided that the manufacturer, installer or tester can provide information or data
to adequately support and justify the alternative.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
Referenced documents which are not found to be publicly available in the expected location might be found at
http://docbox.etsi.org/Reference.
NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee
their long term validity.
[1] ICAO Doc 9816 (First Edition 2004): "Manual on VHF Digital Link (VDL) Mode 4 -
Part 2: Detailed Technical Specifications".
[2] ICAO Annex 10 to the Convention on International Civil Aviation: "Aeronautical
Telecommunications, Volume III: Communication Systems, Part I: Digital Data Communication
Systems, chapter 6".
[3] RTCA DO-242A: "Minimum Aviation System Performance Standards for Automatic Dependent
Surveillance Broadcast (ADS-B)".
[4] ETSI EN 302 842-1 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF air-ground and air-air Digital Link (VDL) Mode 4 radio equipment; Technical characteristics
and methods of measurement for aeronautical mobile (airborne) equipment; Part 1: Physical
layer".
ETSI

---------------------- Page: 10 ----------------------

SIST EN 302 842-3 V1.2.1:2007
 9 ETSI EN 302 842-3 V1.2.1 (2006-12)
[5] ETSI EN 302 842-2 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF air-ground and air-air Digital Link (VDL) Mode 4 radio equipment; Technical characteristics
and methods of measurement for aeronautical mobile (airborne) equipment; Part 2: General
description and data link layer".
[6] ETSI EN 302 842-4 (V1.2.1): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF air-ground and air-air Digital Link (VDL) Mode 4 radio equipment; Technical characteristics
and methods of measurement for aeronautical mobile (airborne) equipment; Part 4: Point-to-point
functions".
[7] Amendments 76 and 77 to Volume I of Annex 10 to the Convention on International Civil
Aviation, International Civil Aviation Organization: Appendix B-B2, 3.6 "Ground-based
augmentation system (GBAS)".
NOTE: http://www.icao.int.
[8] EUROCAE ED-114: "Minimum Operational Performance Specification for Global Navigation
Satellite Ground Based Augmentation System Ground Equipment to Support Category I
Operations".
NOTE: http://www.eurocae.org.
[9] ETSI EN 301 842 (all parts): "Electromagnetic compatibility and Radio spectrum Matters (ERM);
VHF air-ground Data Link (VDL) Mode 4 radio equipment; Technical characteristics and methods
of measur
...