ETSI TS 102 112-1 V1.1.1 (2002-09)

SLOVENSKI STANDARD
01-januar-2005
Storitve in protokoli za napredna omrežja (SPAN) – Preskušanje integracije
omrežja med IN, PLMN in ISDN – 1. del: Zgradba preskušalnega niza in namen
preskušanja (TSS&TP)
Services and Protocols for Advanced Networks (SPAN); Network Integration Testing
between IN, PLMN and ISDN; Part 1: Test Suite Structure and Test purposes (TSS&TP)
Ta slovenski standard je istoveten z: TS 102 112-1 Version 1.1.1
ICS:
33.040.01 Telekomunikacijski sistemi Telecommunication systems
na splošno in general
33.080 Digitalno omrežje z Integrated Services Digital
integriranimi storitvami Network (ISDN)
(ISDN)
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

Technical Specification
Services and Protocols for Advanced Networks (SPAN);
Network Integration Testing between IN, PLMN AND ISDN
Part 1: Test Suite Structure and Test purposes (TSS&TP)

2 ETSI TS 102 112-1 V1.1.1 (2002-09)

Reference
DTS/SPAN-130307-1
Keywords
IN, ISDN, NIT, PLMN, testing, TSS&TP
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE

Tel.: +33 4 92 94 42 00  Fax: +33 4 93 65 47 16

Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88

Important notice
Individual copies of the present document can be downloaded from:
http://www.etsi.org
The present document may be made available in more than one electronic version or in print. In any case of existing or
perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF).
In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive
within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
http://portal.etsi.org/tb/status/status.asp
If you find errors in the present document, send your comment to:
editor@etsi.fr
Copyright Notification
No part may be reproduced except as authorized by written permission.
The copyright and the foregoing restriction extend to reproduction in all media.

© European Telecommunications Standards Institute 2002.
All rights reserved.
TM TM TM
DECT , PLUGTESTS and UMTS are Trade Marks of ETSI registered for the benefit of its Members.
TM
TIPHON and the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members.
TM
3GPP is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners.
ETSI
3 ETSI TS 102 112-1 V1.1.1 (2002-09)
Contents
Intellectual Property Rights.5
Foreword.5
Introduction .5
1 Scope.6
2 References.6
3 Definitions.7
3.1 Definitions related to conformance testing.7
3.2 Definitions related to test purpose descriptions.8
4 Abbreviations.9
5 Numbering Scheme.11
5.1 Examples.12
6 Test Suite Structure (TSS).13
6.1 Support of IN services in the mobile network Mobile - Mobile.13
6.1.1 Number translation services.13
6.1.2 Services with user interactive dialogue.13
6.1.3 Supplementary services.13
6.2 Number translation services between mobile and fixed networks.13
6.2.1 Number translation services between mobile and fixed networks .13
6.2.2 Services with user interactive dialogue between mobile and fixed networks .14
6.2.3 Supplementary services between mobile and fixed networks.14
6.3 Support of IN services in the fixed network.14
6.3.1 Number translation services in fixed networks.14
6.3.2 Services with user interactive dialogue.14
6.3.3 Supplementary services.15
7 Test purposes.15
7.1 Support of IN services in the mobile network, Mobile-Mobile, Mobile - Fixed Networks.15
7.1.1 IN configurations.15
7.1.2 Test purposes for GSM to GSM, Basic call.17
7.1.2.1 Successful.17
7.1.2.2 Unsuccessful.37
7.1.3 Services with user interactive dialogue.39
7.1.3.1 Successful.39
7.1.3.2 Unsuccessful.49
7.1.4 Supplementary Services.51
7.2 Support of IN services - Fixed Networks - Mobile .87
7.2.1 IN configurations.87
7.2.2 Test purposes for ISDN to GSM, Basic call .90
7.2.2.1 Successful.90
7.2.2.2 Unsuccessful.107
7.2.3 Services with user interactive dialogue.109
7.2.3.1 Successful.109
7.2.3.2 Unsuccessful.120
7.2.4 Supplementary Services.122
7.3 Support of IN services - Fixed Networks - Fixed Networks .159
7.3.1 IN configurations.159
7.3.2 Test purposes for ISDN to ISDN, Basic call .162
7.3.2.1 Successful.162
7.3.2.2 Unsuccessful.177
7.3.3 Services with user interactive dialogue.179
7.3.3.1 Successful.179
7.3.3.2 Unsuccessful.188
ETSI
4 ETSI TS 102 112-1 V1.1.1 (2002-09)
7.3.4 Supplementary Services.189
Annex A (normative): GSM SETUP_PAR_ID parameter values .244
Annex B (normative): ISDN SETUP_PAR_ID parameter values.248
Annex C (normative): Interface parameter values .251
Annex D (informative): Bibliography.262
History .269

ETSI
5 ETSI TS 102 112-1 V1.1.1 (2002-09)
Intellectual Property Rights
IPRs essential or potentially essential to the present document may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (http://webapp.etsi.org/IPR/home.asp).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Foreword
This Technical Specification (TS) has been produced by ETSI Technical Committee Services and Protocols for
Advanced Networks (SPAN).
The present document is part 1 of a multi-part deliverable covering the Network Integration Testing between IN, PLMN
and ISDN as identified below:
Part 1: "Test Suite Structure and Test Purposes (TSS&TP)";
Part 2: "Implementation Conformance Statement (ICS), partial Implementation eXtra Information for Testing
(IXIT) proformas and Abstract Test Suite (ATS)".
The present document was developed by EURESCOM P1106 as Deliverable 2 Volume 3 and made freely and publicly
available to ETSI TC SPAN for publication.
Introduction
The present document contains the Test Suite Structure and Test Purposes (TSS&TP) for Network Integration Testing
for the European ISDN and PLMN, covering the most used IN services and the interworking between the mobile and
fix networks. All bearer services (and associated teleservices) and supplementary services are checked for interworking
capability and compatibility, in the European ISDN and PLMN.
ETSI
6 ETSI TS 102 112-1 V1.1.1 (2002-09)
1 Scope
The present document specifies the Test Suite Structure and Test Purposes (TSS&TP) for Network Integration Testing
(NIT) to verify the overall compatibility for the most used IN services based on the CS3 and the INAP/CAP/ISUP
interworking between the mobile and fix networks.
Network Integration Testing will assure that the appropriate requested features pass between an ISDN subscriber and
the mobile subscriber across the national or international ISUP (ISUP V2) interface and the IN interfaces CAP/INAP.
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication and/or edition number or version number) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies.
[1] ETSI EN 300 403-1: "Integrated Services Digital Network (ISDN); Digital Subscriber Signalling
System No. one (DSS1) protocol; Signalling network layer for circuit-mode basic call control;
Part 1: Protocol specification [ITU-T Recommendation Q.931 (1993), modified]".
[2] ETSI ETS 300 083: "Integrated Services Digital Network (ISDN); Circuit mode structured bearer
service category usable for speech information transfer; Terminal requirements for end-to-end
compatibility".
[3] ETSI ETS 300 084: "Integrated Services Digital Network (ISDN); Circuit mode structured bearer
service category usable for 3,1 kHz audio information transfer; Terminal requirements necessary
for end-to-end compatibility".
[4] ETSI EN 300 267-1: "Integrated Services Digital Network (ISDN); Telephony 7 kHz,
videotelephony, audiographic conference and videoconference teleservices; Digital Subscriber
Signalling System No. one (DSS1) protocol; Part 1: Protocol specification".
[5] ETSI ETS 300 080: "Integrated Services Digital Network (ISDN); ISDN lower layer protocols for
telematic terminals ".
[6] ETSI ETS 300 103: "Integrated Services Digital Network (ISDN); Support of CCITT
Recommendation X.21, X.21 bis and X.20 bis based Data Terminal Equipments (DTEs) by an
ISDN Synchronous and asynchronous terminal adaptation functions ".
[7] ETSI EN 300 138-1: "Integrated Services Digital Network (ISDN); Closed User Group (CUG)
supplementary service; Digital Subscriber Signalling System No. one (DSS1) protocol;
Part 1: Protocol specification".
[8] ETSI EN 300 207-1: "Integrated Services Digital Network (ISDN); Diversion supplementary
services; Digital Subscriber Signalling System No. One (DSS1); Part 1: Protocol specification".
[9] ETSI ETS 300 289 (1994): "Business TeleCommunications (BTC); 64 kbit/s digital unrestricted
leased line with octet integrity (D64U); Connection characteristics".
[10] ISO/IEC 9646-1: "Information Technology-Open Systems Interconnection- Conformance testing
methodology and framework, Part 1: General Concepts".
[11] ETSI EN 300 940 (GSM 04.08): "Digital cellular telecommunications system (Phase 2+) (GSM);
Mobile radio interface layer 3 specification".
ETSI
7 ETSI TS 102 112-1 V1.1.1 (2002-09)
[12] ITU-T Recommendation Q.699: "Interworking between the digital Subscriber Signalling System
Layer 3 protocol and the Signalling System No.7 ISDN User part".
[13] ITU-T Recommendation Q.764: "Signalling System No. 7 - ISDN User Part signalling
procedures".
[14] ETSI TS 129 078: "Digital cellular telecommunications system (Phase 2+); Universal Mobile
Telecommunications System (UMTS); Customized Applications for Mobile network Enhanced
Logic (CAMEL) Phase 3; CAMEL Application Part (CAP) specification (3GPP TS 29.078
version 4.0.0 Release 4)".
[15] ETSI EN 301 931-2 (V1.1.2): "Intelligent Network (IN); Intelligent Network Capability Set 3
(CS3); Intelligent Network Application Protocol (INAP); Protocol specification; Part 2: SCF-SSF
interface".
[16] ITU-T Recommendation Q.1601: "Signalling system No. 7 - Interaction between N-ISDN and
INAP CS2".
[17] ISO/IEC 7776: "Information technology - Telecommunications and information exchange between
systems - High-level data link control procedures - Description of the X.25 LAPB-compatible
DTE data link procedures".
[18] ISO/IEC 8208: "Information technology - Data communications - X.25 Packet Layer Protocol for
Data Terminal Equipment".
[19] ETSI TS 101 285 (GSM 02.78): "Digital cellular telecommunications system (Phase 2+);
Customized Applications for Mobile network Enhanced Logic (CAMEL); Service definition;
Stage 1".
[20] ETSI TS 101 044 (GSM 03.78): "Digital cellular telecommunications system (Phase 2+);
Customized Applications for Mobile network Enhanced Logic (CAMEL); Stage 2".
[21] ETSI TS 101 046 (GSM 09.78): "Digital cellular telecommunications system (Phase 2+);
Customized Applications for Mobile network Enhanced Logic (CAMEL); CAMEL Application
Part (CAP) specification".
3 Definitions
For the purposes of the present document, the following terms and definitions apply.
3.1 Definitions related to conformance testing
Abstract Test Case: Refer to ISO/IEC 9646-1 [38].
Abstract Test Suite: Refer to ISO/IEC 9646-1 [38].
Implementation Under Test: Refer to ISO/IEC 9646-1 [38].
Lower Tester: Refer to ISO/IEC 9646-1 [38].
Implementation Conformance Statement (ICS) proforma: Refer to ISO/IEC 9646-1 [38].
Implementation eXtra Information for Testing (IXIT) proforma: Refer to ISO/IEC 9646-1 [38].
Point of Control and Observation: Refer to ISO/IEC 9646-1 [38].
Protocol Implementation Conformance Statement: Refer to ISO/IEC 9646-1 [38].
Protocol Implementation eXtra Information for Testing: Refer to ISO/IEC 9646-1 [38].
System Under Test: Refer to ISO/IEC 9646-1 [38].
Test Purpose: Refer to ISO/IEC 9646-1 [38].
ETSI
8 ETSI TS 102 112-1 V1.1.1 (2002-09)
3.2 Definitions related to test purpose descriptions
BC=speech: a Bearer capability information element with its information transfer capability field set to "speech" and its
user information layer one protocol field set to "G.711 A-law" [2]
BC=3,1 kHz audio: a Bearer capability information element with its information transfer capability field set to
"3,1 kHz Audio" and its user information layer one protocol field set to "G.711 A-law" [3]
BC=UDI: a Bearer capability information element with its information transfer capability set to "unrestricted digital
information" [1]
BC=UDI/TA: a Bearer capability information element with its information transfer capability set to "unrestricted
digital information with tones/announcements" and its user information layer one protocol field set to
"Recommendations H.221 and H.242" [4]
BC= V110/X30: a Bearer capability information element with its information transfer capability set to "unrestricted
digital information" and its user information layer 1 field set to "ITUstandardized rate adaption V.110/X.30", including
sync/async and user rate values [1].
HLC=telephony: a High Layer compatibility information element with its high layer characteristics identification field
set to "telephony" [28]
HLC=videotelephony_ic: a High Layer compatibility information element with its high layer characteristics
identification field set to "videotelephony (Recommendation F.721)" and its extended audiovisual characteristics field
set to "capability set of initial channel of Recommendation H.221" [4]
HLC = Facsimile G2/G3: a High Layer compatibility information element with its high layer characteristics
identification field set to "facsimile group 2/3 (Recommendation F.182)" [1]
HLC=facsimile group 4: a High Layer compatibility information element with its high layer characteristics
identification field set to "facsimile group 4 class 1" [1], [5]
HLC=telex: a High Layer compatibility information element with its high layer characteristics identification field set to
"telex" [1]
LLC=telematic_term: a Low Layer compatibility information element with its user information layer 2 field indicating
"ISO/IEC 7776 DTE-DTE operation" and user information layer 3 field indicating "ISO/IEC 8208" [1], [5]
LLC=voice band data via modem: a Low Layer compatibility information element with its user information layer 1
field indicating a "modem type" coding [1]
LLC = V110/X30: a Low Layer compatibility information element with its user information layer 1 field indicating
"ITUstandardized rate adaption V.110/X.30" and including sync/async and user rate values [6]
SI=UPVP: Screening Indicator forwarded to the served user coded as "User-provided, verified and passed"
SI=NP: Screening Indicator coded as "Network provided" [1]
PI=PR: Presentation Indicator coded as "Presentation restricted" [1]
TON=international: Type of number coded as "international" [1]
TON=unknown: Type of number coded as "unknown" [1]
NPI=unknown: Numbering plan identification coded as "unknown" [1]
CUG default request: the calling user do not include in the outgoing SETUP message a explicit request for the CUG
supplementary service [11]
UI length=32: the length of the User information field of the User-user information element is 35 octets
CF active: the call forwarding (U, B or NR) supplementary service is already activated with the address of user C [17]
GSM - Bearer service categories: all bearer service categories provide information transfer between R/S reference
points and allow the use of sub-rate information streams which are rate adapted.
ETSI
9 ETSI TS 102 112-1 V1.1.1 (2002-09)
GSM-BC=UD: Unrestricted Digital Information (UD ); Provides the transfer of unrestricted digital information.
GSM-BC= 3,1 kHz (External to the PLMN): Used to select a "3,1 kHz audio" interworking function at the MSC.
This service category is used when interworking with the ISDN or PSTN "3,1 kHz audio" service and includes the
capability to select a modem at the interworking function. "External to the PLMN" indicates that the "3,1 kHz audio"
service is only used outside of the PLMN, in the ISDN/PSTN. The connection within the PLMN, user access point to
the interworking function, is an unrestricted digital connection.
Alternate Speech/Data: Provides the capability to swap between speech and data during a call.
• If either the speech or data portion of the call requires a full rate channel, a full rate channel shall be used for
the duration of the call.
• The access interface at the mobile station for the data portion is assumed to be a standard data interface. Some
means must be provided to select the speech/data capability.
Speech followed by Data: Provides a speech connection first and then at some time while the call is in progress, the
user can switch to a data connection. The user cannot switch back to speech after the data portion. If either the speech or
data portion of the call requires a full rate channel, a full rate channel shall be used from the start of the call. The
network may then change to a half rate channel for the data portion.
GSM teleservices: Teleservices supported by a GSM PLMN are described by a number of attributes which are
intended to be largely independent. They are grouped into three categories:
- High layer attributes.
- Low layer attributes (describing the Bearer capabilities which support the Teleservice).
- Information transfer attributes.
- Access attributes.
- General attributes.
GSM-BC= Speech (TS 11): This service provides the transmission of speech information and audible signalling tones
of the PSTN/ISDN. In the GSM PLMN and the fixed network processing technique appropriate for speech such as
analogue transmission, echo cancellation and low bit rate voice encoding may be used.
Alternate speech and facsimile group 3 (TS 61): This Teleservice allows the connection of ITUgroup 3 fax apparatus
(send and/or receive) to the mobile stations of a GSM PLMN. Facsimile connections may be established to/from
group 3 apparatus in the PSTN, ISDN or GSM PLMN.
Automatic Facs. group 3 (TS 62): This teleservice allows connection of ITUgroup 3 fax apparatus to and from the
mobile stations of a GSM PLMN. Facsimile connections may be established to and from group 3 apparatus in the
PSTN, ISDN or GSM PLMN.
4 Abbreviations
For the purposes of the present document, the following abbreviations apply:
3PTY Three-ParTY conference
ATS Abstract Test Suite
BC Bearer Capability information element
BS Base Station
BSC Base Station Controller
BSS Base Station Sub-system
BSS Base Station System
CAMEL Customized Applications for Mobile network Enhanced Logic
CD Call Deflection
CFB Call Forwarding Busy
CFNR Call Forwarding No Response
CFNRc Call Forwarding on mobile subscriber Not Reachable
CFNRy Call Forwarding on No Reply
ETSI
10 ETSI TS 102 112-1 V1.1.1 (2002-09)
CFU Call Forwarding Unconditional
CLIP Calling Line Identification Presentation
CLIR Calling Line Identification Restriction
COLP COnnected Line identification Presentation
COLR COnnected Line identification Restriction
CONF CONFerence (add-on)
CUG Closed User Group
CW Call Waiting
DFC Disconnect Forward Connection
ECT Explicit Call Transfer
FPH FreePHone service
GMSC Gateway MSC
GSM Global System for Mobile communication
HLC High Layer Compatibility information element
HLR Home Location Register
HPLMN Home Public Land Mobile Network
IN Intelligent Network
INAP Intelligent Network Application Part
IP Internet Protocol
ISDN Integrated Services Digital Network
ISUP ISDN User Part
LAN Locale Access Network
LLC Low Layer Compatibility information element
MAP Mobile Application Part
MCID Malicious Call IDentification
MS Mobile Station
MS Mobile Subscriber
MSC Mobile Switching Center
MT Mobile Terminal
MT Mobile Terminated
MTP Message Transfer Part
NIT Network Integration Testing
ONP Open Network Provision
OSI Open Systems Interconnection
PI Presentation indicator
PICS Protocol Implementation Conformance Statement
PIXIT Protocol Implementation eXtra Information for Testing
PLMN Public Land Mobile Network
PSTN Public Switched Telephone Network
SCCP Signaling Connection and Control Part
SCF Service Control Function
SCP Service Control Point
SGSN Serving GPRS Support Node
SI Screening Indicator
SMS Short Message Service
SS Supplementary Service
SSP Service Switching Point
SUB Subaddressing
TCAP Transaction Capabilities Application Part
TON Type Of Number
TP Terminal Portability
TP Test Plant
TSS Test Suite Structure
TSS&TP Test Suite Structure and Test Purposes
UD Unrestricted Digital information
UMTS Universal Mobile Telecommunications System
UUS User-to-User Signalling
UUS1 UUS service 1
UUS2 UUS service 2
UUS3 UUS service 3
VLR Visitor Location Register
VLR Visitor Location Register
ETSI
11 ETSI TS 102 112-1 V1.1.1 (2002-09)
VPLMN Visited Public Land Mobile Network
5 Numbering Scheme
Pos. 1: Network of the A-Subscriber
Pos. 2: Network of the B-Subscriber
Pos. 3: Network of the C-Subscriber
Pos. 4: Network of the D-Subscriber
Pos. 5: Network of the E-Subscriber
The following Network Codes apply:
_: No such network used (used e.g. for C-Subscriber in successful A to B Calls)
(underscore makes it easier to read the name)
P: PSTN
I: ISDN
G: GSM (w/ HCSCD & GPRS)
(Extensions will be added when needed)
Pos. 6 and 7: Bearer- or Teleservice involved
xx: defined per PIXIT value.
NOTE: This may be appropriate for Test Purposes (provided the Test Purpose states for which Bearer- and/or
Tele Services it should be tested). It is however NOT appropriate for Test Cases since it would be
detrimental to Test Automation:
- SP: Speech;
- AU: 3,1 kHz Audio;
- UD: UDI;
- FX: Facsimile G3;
- HA: HSCSD - 3,1 kHz audio;
- HU: HSCSD - UDI.
Pos. 8 and 9:
__: No Supplementary Services Involved / Successful
_U: No Supplementary Services Involved / Unsuccessful
SS: Supplementary Services Involved
SI: Supplementary Services interaction
SN: Nonsymmetrical Supplementary Services Involved
ST: Supplementary Services transparent

IN SERVICES
Number translation services:
N_: No Supplementary Services Involved / Basic Call Successful/Number translation services
NU: No Supplementary Services Involved / Basic Call Unsuccessful/Number translation services
NS: Supplementary Services Involved / Number translation services
NI: Supplementary Services interaction / Number translation services
NN: Nonsymmetrical Supplementary Services Involved / Number translation services
NT: Supplementary Services transparent to IN / Number translation services
Services with user interactive dialogue:
I_: No Supplementary Services Involved / Basic Call Successful/Services with user interactive
dialogue
IU: No Supplementary Services Involved / Basic Call Unsuccessful/ Services with user interactive
dialogue
IS: Supplementary Services Involved / Services with user interactive dialogue
II: Supplementary Services interaction / Services with user interactive dialogue
ETSI
12 ETSI TS 102 112-1 V1.1.1 (2002-09)
IN: Nonsymmetrical Supplementary Services Involved / Services with user interactive dialogue
IT: Supplementary Services transparent to IN / Services with user interactive dialogue
Other services:
O_: No Supplementary Services Involved / Basic Call Successful/ Other services
OU: No Supplementary Services Involved / Basic Call Unsuccessful/ Other services
OS: Supplementary Services Involved / Other services
OI: Supplementary Services interaction / Other services
ON: Non symmetrical Supplementary Services Involved / Other services
OT: Supplementary Services not impact by IN / Other services
Pos. 10 to 20: YYYY Name of individual Test Group (if needed) If supplementary services are involved the following
codes are used.
Services Name of individual test group
3PTY 3PTY
Call Barring services CBS
Call Barring services outgoing CBSo
CCBS CCBS
CD CD
CFB CFB
CFNR CFNR
CFU CFU
CLIP CLIP
CLIR CLIR
COLP COLP
COLR COLR
CONF CONF
CUG CUG
CW CW
ECT ECT
HOLD HOLD
MCID MCID
MPTY MPTY
SUB SUB
TP
TP
UUS1 UUS1
UUS1 implicit UUS1i
UUS1 explicit UUS1e
Pos. Last two positions: XX Number of individual Test Purpose.
5.1 Examples
Basic Call:
Speech IG___SPN__xx
1 2 3 4 5 6 7 8 9 10 11
I G _ _ _ S P N _ x x
Supplementary Services:
CLIP IG___xxSSCLIP xx
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
I G _ _ _ X X N S C L I P x x
ETSI
13 ETSI TS 102 112-1 V1.1.1 (2002-09)
6 Test Suite Structure (TSS)
6.1 Support of IN services in the mobile network Mobile -
Mobile
6.1.1 Number translation services
Number
translation C – Plane / U–Plane
Services Basic_Call Successful  GG___xxN_xx

Unsuccessful
GG___xxNUxx
6.1.2 Services with user interactive dialogue
Interactive
dialogue C – Plane / U–Plane
Basic_Call Successful
Speech GG___SP I_xx
Unsuccessful Speech GG___SP IUxx

6.1.3 Supplementary services
Supplementary
Services
Control – Plane Services impact by IN
CLIP GG___xx NS CLIP xx
CLIR GG___xx NS CLIR xx
COLP GG___xx NS COLP xx
CFxx GG___xx NS CFxx
CFU GG___xx NS CFUxx
CFB GG___xx NS CFB xx
CFNR GG___xx NS CFNR xx
CCBS GG___xx NS CCBS xx
6.2 Number translation services between mobile and fixed
networks
6.2.1 Number translation services between mobile and fixed networks
Number
Translation
Services Control – Plane
ISDN/GSM Basic_Call Successful  IG___xxN_xx

Unsuccessful
IG___xxNUxx
ETSI
14 ETSI TS 102 112-1 V1.1.1 (2002-09)
6.2.2 Services with user interactive dialogue between mobile and fixed
networks
Services with
user interactive
dialogue Control – Plane
ISDN/GSM Basic_Call Successful
IG___I_xx
Unsuccessful IG__IUxx
6.2.3 Supplementary services between mobile and fixed networks
Supplementary
Services
Control – Plane Services impact
by IN
CLIP IG___xx NS CLIPxx
CLIR IG___xx NS CLIRxx
COLP IG___xx NS COLPxx
CFxx IG___xx NS CFxx
CFU IG___xx NS CFUxx
CFB IG___xx NS CFB xx
CFNRy IG___xx NS CFNR xx
CCBS IG___xx NS CCBS xx
MCID IG___xx NS MCIDxx
6.3 Support of IN services in the fixed network
6.3.1 Number translation services in fixed networks
Number
Translation
Services Control – Plane
ISDN Basic_Call Successful  II___xxN_xx

Unsuccessful  II___xxNUxx
6.3.2 Services with user interactive dialogue
Services with
user interactive
dialogue Control – Plane
ISDN/GSM Basic_Call Successful
II___I_xx
Unsuccessful II__IUxx
ETSI
15 ETSI TS 102 112-1 V1.1.1 (2002-09)
6.3.3 Supplementary services
Supplementary
Services
Control – Plane Services impact
by IN
CLIP II___xx NS CLIPxx
CLIR II___xx NS CLIRxx
COLP II___xx NS COLPxx
CFxx II___xx NS CFxx
CFU II___xx NS CFUxx
CFB II___xx NS CFB xx
CFNR II___xx NS CFNR xx
CD II___xx NS CDxx
CONF II___xx NS CONFxx
CCBS II___xx NS CCBS xx
UUS1 II___xx NS UUS1xx
UUS2 II___xx NS UUS2xx
UUS3 II___xx NS UUS3xx
MCID II___xx NS MCIDxx
ECT II___xx NS ECT xx
7 Test purposes
The following note applied to all tables.
NOTE: Parameters values of either ISUP/CAP interface or A/CAP interface are used only for HSCSD.
7.1 Support of IN services in the mobile network,
Mobile-Mobile, Mobile - Fixed Networks
7.1.1 IN configurations
gsmSCF
CAP interface
gsmSRF
CAP relay gsmSSF
interface
Internal interface
Internal interface
OCH_MSC
Mobile A interface ISUP interface Destination
Station exchange
Figure 1: Outgoing case (gsmSSF relay)
ETSI
16 ETSI TS 102 112-1 V1.1.1 (2002-09)

gsmSCF
CAP interface CAP interface
gsmSRF or
Assisting SSP
gsmSSF
Internal interface
ISUP interface
OCH_MSC
A interface ISUP interface
Mobile Destination
Station exchange
Figure 2: Outgoing case (direct path gsmSCF to gsmSRF or assist with relay)

gsmSCF gsmSCF
CAP interface CAP interface
CAP relay CAP relay
interface interface
gsmSRF gsmSRF
gsmSSF gsmSSF
Internal interface Internal interface Internal interface Internal interface
Originating MT_GMSC MT_CF_MSC Destination
ISUP Internal ISUP ISUP
exchange exchange
interface interface interface
Figure 3: Terminating GMSC case (gsmSSF relay)

gsmSCF gsmSCF
CAP interface CAP interface CAP interface CAP interface
gsmSRF or gsmSRF or
gsmSSF gsmSSF
assisting assisting
SSP SSP
ISUP interface Internal interface Internal interface ISUP interface
MT_GMSC MT_CF_MSC
Originating Destination
ISUP Internal ISUP ISUP
exchange exchange
interface interface interface
Figure 4: Terminating GMSC case (direct path gsmSCF to gsmSRF or assist with relay)
ETSI
17 ETSI TS 102 112-1 V1.1.1 (2002-09)
7.1.2 Test purposes for GSM to GSM, Basic call
7.1.2.1 Successful
Successful
GG___xx N_ 01 GSM ref. to: Other ref.:
EN 300 940
TS 101 285 (GSM 02.78) St 1
TS 101 044 (GSM 03.78) St 2
TS 101 046 (GSM 09.78) St 3
TSS reference: GSM to GSM/ Number translation services/Successful
GSM selection Numb_Trans
criteria orign.:
GSM selection Numb_Trans
criteria term.:
Test purpose: Verify that the Call is routed to the Called Party Number with the Continue operation.
Parameters which were received in the IAM and are not replaced by parameters of the
Continue operation are treated according to the normal procedures.
Pre test Conditions:
A-subscriber provisioned in HLR for re-routing service
Location update performed for originating A-Subscriber
Terminating B-Subscriber routed to ISUP link
PCO / PO Initial Detection point
ISUP/CAP Interface Verify that the IUT can successfully map the IAM parameter IAM_PAR_ID to the
parameter InitialDP parameter InitiallDP_PAR_ID (see annex C).
Values (note): Receiving of Continue message
On receipt of a Continue operation from the SCP call processing is resumed.
The SSP may modify signalling information received from the preceding exchange
according to the capabilities used on the outgoing route. Signalling information that may
be changed are nature of connection indicator and propagation delay counter. Other
signalling information is passed on transparently, e.g. the access transport parameter,
user service information, etc. The order of information elements carried in the access
transport parameter received from the incoming exchange shall be retained.
Sending of backward messages
Verify that the IUT can successfully map the backward messages ACM, CPG (alerting or
in-band information, progress), CON and ANM.
Receiving of Release message
Verify that the IUT can successfully release the call like an ordinary transit exchange.
PCO / PO Initial Detection point
A/CAP interface Verify that the IUT can successfully map the SETUP_PAR_ID parameter to the InitialDP
parameter
parameter InitiallDP_PAR_ID (see annex C).
Values (note): Sending of backward messages
Verify that the IUT can successfully map the backward messages CALL PROCEEDING,
ALERTING, PROGRESS or CONNECT to the originating side.
Receiving of a Release message
Verify that the IUT can successfully release the call.
GSM parameter GSM-BC = GSM-BC_ID
values orign.:
synchronous/ asynchronous mode: MODE
user rate: USER_RATE
fixed network user rate: FNU_RATE (note).
maximum number of traffic channels: No_TCH (note).
air interface user rate: AIU_RATE (note).
acceptable channel coding: TCH_FX_X (note).
LLC =  BC_ID
synchronous/ asynchronous mode: MODE
user rate: USER_RATE
HLC = HLC_ID
ETSI
18 ETSI TS 102 112-1 V1.1.1 (2002-09)
GG___xx N_ 01 GSM ref. to: Other ref.:
EN 300 940
TS 101 285 (GSM 02.78) St 1
TS 101 044 (GSM 03.78) St 2
TS 101 046 (GSM 09.78) St 3
GSM parameter GSM-BC = GSM-BC_ID
values term.: synchronous/ asynchronous mode: MODE
user rate: USER_RATE
LLC = synchronous/ asynchronous mode: MODE
user rate: USER_RATE
HLC = HLC_ID
Comments:
GG___SPN_01
BSS_A MSC_A
SSP_A SCP_A MSC_B BSS_B
SETUP
iam
CALLPROC
IDP
CUE
iam
PROGRESS acm
acm (note)
SETUP
CALLCONF
ALERT
acm
acm
CONNECT
ALERT anm
CONNECTACK
anm
CONNECT
CONNECTACK
Release A
DISCONNECT
RELEASE
rel
DISCONNECT
rel
RELEASE
rlc rlc
RELEASE COM
RELEASE COM
NOTE: The sending of an early ACM message is optional.

Figure 5: Number translation service flow with Continue Message
ETSI
19 ETSI TS 102 112-1 V1.1.1 (2002-09)
GG___xx N_ 02 GSM ref. to: Other ref.:
EN 300 940
TS 101 285 (GSM 02.78) St 1
TS 101 044 (GSM 03.78) St 2
TS 129 078 (GSM 29.078) St 3,
clause A.2
TSS reference: GSM to GSM/Number translation services/Successful
GSM selection Numb_Trans
criteria orign.:
GSM selection
Numb_Trans
criteria term.:
Test purpose: Verify that the Call is routed to the Called Party Number without any number translation
activity in between if the SCP decides that Rerouting and Called Party Number
translation are not necessary. Ensure that the parameter received in the
ServiceInteractionIndicatorsTwo received from the SCP in the ContinueWithArgument
operation will be sent in the IAM by the SSP.

Pre test Conditions:
A-subscriber provisioned in HLR for re-routing service
Location update performed for originating A-Subscriber
Terminating B-Subscriber routed to ISUP link
PCO / PO Initial Detection point
ISUP/CAP Interface
Verify that the IUT can successfully map the IAM parameter IAM_PAR_ID to the
parameter InitialDP parameter InitiallDP_PAR_ID (see annex C).
Values (note): Receiving of Continue message
On receipt of a Continue operation from the SCP call processing is resumed.
Ensure that the CONTINUE_PAR_ID parameters received from the SCP in the
ContinueWithArgument operation will be mapped in the IAM by the SSP.
Sending of backward messages
Verify that the IUT can successfully map the backward messages ACM, CPG (alerting or
in-band information, progress), CON and ANM.
Receiving of Release message
Verify that the IUT can successfully release the call like an ordinary transit exchange.
PCO / PO Initial Detection point
A/CAP interface
Verify that the IUT can successfully map the SETUP_PAR_ID parameter to the InitialDP
parameter parameter InitiallDP_PAR_ID (see annex C).
:
Values (note) Sending of backward messages
Verify that the IUT can successfully map the backward messages CALL PROCEEDING,
ALERTING, PROGRESS or CONNECT to the originating side.
Receiving of a Release message
Verify that the IUT can successfully release the call.
GSM parameter GSM-BC = GSM-BC_ID
values orign.:  Synchronous/ asynchronous mode: MODE
user rate: USER_RATE
fixed network user rate: FNU_RATE (note).
maximum number of traffic channels: No_TCH (note).
air interface user rate: AIU_RATE (note).
acceptable channel coding: TCH_FX_X (note).
LLC =  BC_ID
Synchronous/ asynchronous mode: MODE
user rate: USER_RATE
HLC = HLC_ID
GSM parameter GSM-BC = GSM-BC_ID
values term.:
Synchronous/ asynchronous mode: MODE
user rate: USER_RATE
LLC = synchronous/ asynchronous mode: MODE
user rate: USER_RATE
HLC = HLC_ID
Comments:
ETSI
20 ETSI TS 102 112-1 V1.1.1 (2002-09)
GG___SPN_02
BSS_A MSC_A SSP_A SCP_A MSC_B
BSS_B
SETUP
iam
CALLPROC
IDP
CWA
iam
PROGRESS
acm acm (note)
SETUP
CALLCONF
ALERT
acm
acm
CONNECT
ALERT
anm
CONNECTACK
anm
CONNECT
CONNE
...