EN IEC 61753-131-03:2021
(Main)Fibre optic interconnecting devices and passive components - Performance standard - Part 131-03: Single-mode mechanical fibre splice for category OP - Outdoor protected environment
Fibre optic interconnecting devices and passive components - Performance standard - Part 131-03: Single-mode mechanical fibre splice for category OP - Outdoor protected environment
This part of IEC 61753 contains the minimum tests, test severities and measurement requirements which a mechanical fibre splice need to satisfy in order to be categorised as meeting the requirements of single-mode fibre splice for use in category OP (Outdoor protected) environments, as defined in IEC 61753-1. This document for mechanical splices defines the requirements for standard optical performance under a set of specified conditions. The standard contains a series or a set of tests and measurements with clearly stated conditions, severities and pass/fail criteria. The series of tests, commonly referred to as an operating service environment or performance category, is intended to be a basis to prove the product’s ability to satisfy the requirements of a specific application, market sector or user group.
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil 131-03: Mechanische Spleiße für Einmoden-Lichtwellenleiter für die Kategorie OP - Freiluft, geschützte Umgebung
Dispositifs d’interconnexion et composants passifs fibroniques – Norme de performance - Partie 131-03: Épissure mécanique de fibres unimodales pour catégorie OP – Environnement extérieur protégé
IEC 61753-131-03:2021 indique les exigences minimales relatives aux essais, aux sévérités des essais ainsi qu’aux mesurages auxquelles il est nécessaire qu’une épissure mécanique de fibre satisfasse pour être classée comme satisfaisant aux exigences des épissures de fibres unimodales destinées à être utilisées dans des environnements de catégorie extérieur protégé (OP – Outdoor protected), tels qu’ils sont définis dans l’IEC 61753-1. Le présent document applicable aux épissures mécaniques définit les exigences de performance optique normalisée selon un ensemble de conditions spécifiées. La norme contient une série ou un ensemble d'essais et de mesurages dont les conditions, les sévérités et les critères d’acceptation/de rejet sont clairement indiqués. La série d'essais, à laquelle il est généralement fait référence en tant que catégorie de performance ou d'environnement de service de fonctionnement, est destinée à servir de base pour démontrer la capacité du produit à satisfaire aux exigences d'un secteur de marché, d'un groupe d'utilisateurs ou d'une application spécifique. Cette première édition annule et remplace l’IEC 61753-131-3 la première édition parue en 2010. Cette édition constitue une révision technique. Cette édition inclut les modifications techniques majeures suivantes par rapport à l'édition précédente: a) ajout de définitions; b) ajout de l’IEC 60068-2-10 essai de moisissure et sévérité d'essai pour les matériaux; c) remplacement des essais de catégorie U de l’IEC 61753-1:2007 et de leurs sévérités par les essais de catégorie OP de l’IEC 61753‑1:2018; d) ajout de l’exigence de conformité des dimensions à l’IEC 61756-1; e) ajout de l'essai de moment de flexion; f) modification de la température basse dans l’essai de froid et l’essai de variations de température à −25°C. Si 40°C est exigé, l’utilisateur peut se reporter à la catégorie OP+.
Optični spojni elementi in pasivne komponente - Izvedbeni standard - 131-03. del: Enorodovna mehanska optična spojnica za kategorijo OP - Zunanje zaščiteno okolje (IEC 61753-131-03:2021)
Ta del standarda IEC 61753 vsebuje minimalne zahteve glede preskusov, stopenj zahtevnosti preskusov in merjenja, ki jih mora izpolnjevati mehanska optična spojnica, da ustreza zahtevam enorodovne optične spojnice za uporabo v kategoriji OP (Zunanje zaščiteno okolje), kot je opredeljeno v standardu IEC 61753-1.
General Information
Relations
Standards Content (Sample)
SLOVENSKI STANDARD
01-januar-2022
Nadomešča:
SIST EN 61753-131-3:2011
Optični spojni elementi in pasivne komponente - Izvedbeni standard - 131-03. del:
Enorodovna mehanska optična spojnica za kategorijo OP - Zunanje zaščiteno
okolje (IEC 61753-131-03:2021)
Fibre optic interconnecting devices and passive components - Performance standard -
Part 131-03: Single-mode mechanical fibre splice for category OP - Outdoor Protected
environment (IEC 61753-131-03:2021)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Betriebsverhalten - Teil
131-3: Mechanische Spleiße für Einmoden- Lichtwellenleiter für die Kategorie OP -
Freiluft, geschützte Umgebung (IEC 61753-131-03:2021)
Dispositifs d’interconnexion et composants passifs fibroniques - Norme de performance -
Partie 131-03 : Épissure mécanique de fibres unimodales pour catégorie OP -
Environnement extérieur protégé (IEC 61753-131-03:2021)
Ta slovenski standard je istoveten z: EN IEC 61753-131-03:2021
ICS:
33.180.20 Povezovalne naprave za Fibre optic interconnecting
optična vlakna devices
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EUROPEAN STANDARD EN IEC 61753-131-03
NORME EUROPÉENNE
EUROPÄISCHE NORM
November 2021
ICS 33.180.20 Supersedes EN 61753-131-3:2011 and all of its
amendments and corrigenda (if any)
English Version
Fibre optic interconnecting devices and passive components -
Performance standard - Part 131-03: Single-mode mechanical
fibre splice for category OP - Outdoor protected environment
(IEC 61753-131-03:2021)
Dispositifs d'interconnexion et composants passifs Lichtwellenleiter - Verbindungselemente und passive
fibroniques - Norme de performance - Partie 131-03: Bauteile - Betriebsverhalten - Teil 131-3: Mechanische
Épissure mécanique de fibres unimodales pour catégorie Spleiße für Einmoden- Lichtwellenleiter für die Kategorie
OP - Environnement extérieur protégé OP - Freiluft, geschützte Umgebung
(IEC 61753-131-03:2021) (IEC 61753-131-03:2021)
This European Standard was approved by CENELEC on 2021-11-08. CENELEC members are bound to comply with the CEN/CENELEC
Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC
Management Centre or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic,
Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the
Netherlands, Norway, Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland,
Turkey and the United Kingdom.
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2021 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members.
Ref. No. EN IEC 61753-131-03:2021 E
European foreword
The text of document 86B/4500/FDIS, future edition 1 of IEC 61753-131-03, prepared by SC 86B
“Fibre optic interconnecting devices and passive components” of IEC/TC 86 “Fibre optics” was
submitted to the IEC-CENELEC parallel vote and approved by CENELEC as
The following dates are fixed:
• latest date by which the document has to be implemented at national (dop) 2022–08–08
level by publication of an identical national standard or by endorsement
• latest date by which the national standards conflicting with the (dow) 2022–11–08
document have to be withdrawn
This document supersedes EN 61753-131-3:2011 and all of its amendments and corrigenda (if any).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CENELEC shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national committee. A
complete listing of these bodies can be found on the CENELEC website.
Endorsement notice
The text of the International Standard IEC 61753-131-03:2021 was approved by CENELEC as a
European Standard without any modification.
In the official version, for Bibliography, the following notes have to be added for the standards
indicated:
IEC 60721-3-1 NOTE Harmonized as EN IEC 60721-3-1
IEC 60721-3-2 NOTE Harmonized as EN IEC 60721-3-2
IEC 62005 (series) NOTE Harmonized as EN IEC 62005 (series)
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following documents are referred to in the text in such a way that some or all of their content
constitutes requirements of this document. For dated references, only the edition cited applies. For
undated references, the latest edition of the referenced document (including any amendments)
applies.
NOTE 1 Where an International Publication has been modified by common modifications, indicated by (mod), the
relevant EN/HD applies.
NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available
here: www.cenelec.eu.
Publication Year Title EN/HD Year
IEC 60068-2-10 - Environmental testing - Part 2–10: Tests - EN 60068-2-10 -
Test J and guidance: Mould growth
IEC 60793-2-50 - Optical fibres - Part 2–50: Product EN IEC 60793-2-50 -
specifications - Sectional specification for
class B single-mode fibres
IEC 61073-1 - Fibre optic interconnecting devices and EN 61073-1 -
passive components - Mechanical splices
and fusion splice protectors for optical
fibres and cables - Part 1: Generic
specification
IEC 61300 series Fibre optic interconnecting devices and EN 61300 series
passive components - Basic test and
measurement procedures
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 -
passive components - Basic test and
measurement procedures - Part 1: General
and guidance
IEC 61300-2-1 - Fibre optic interconnecting devices and EN 61300-2-1 -
passive components - Basic test and
measurement procedures - Part 2–1: Tests
- Vibration (sinusoidal)
IEC 61300-2-4 - Fibre optic interconnecting devices and EN IEC 61300-2-4 -
passive components - Basic test and
measurement procedures - Part 2–4: Tests
- Fibre or cable retention
IEC 61300-2-5 - Fibre optic interconnecting devices and EN 61300-2-5 -
passive components - Basic test and
measurement procedures - Part 2–5: Tests
- Torsion
IEC 61300-2-7 - Fibre optic interconnecting devices and EN 61300-2-7 -
passive components - Basic test and
measurement procedures - Part 2–7: Tests
- Bending moment
IEC 61300-2-9 - Fibre optic interconnecting devices and EN 61300-2-9 -
passive components - Basic test and
measurement procedures - Part 2–9: Tests
- Shock
IEC 61300-2-17 - Fibre optic interconnecting devices and EN 61300-2-17 -
passive components - Basic test and
measurement procedures - Part 2–17:
Tests - Cold
IEC 61300-2-18 - Fibre optic interconnecting devices and EN 61300-2-18 -
passive components - Basic test and
measurement procedures - Part 2–18:
Tests - Dry heat - High temperature
endurance
IEC 61300-2-22 - Fibre optic interconnecting devices and - -
passive components - Basic test and
measurement procedures - Part 2–22:
Tests - Change of temperature
IEC 61300-2-26 - Fibre optic interconnecting devices and EN 61300-2-26 -
passive components - Basic test and
measurement procedures - Part 2–26:
Tests - Salt mist
IEC 61300-2-27 - Fibre optic interconnecting devices and EN 61300-2-27 -
passive components - Basic test and
measurement procedures - Part 2–27:
Tests - Dust - Laminar flow
IEC 61300-2-33 - Fibre optic interconnecting devices and EN 61300-2-33 -
passive components - Basic test and
measurement procedures - Part 2–33:
Tests - Assembly and disassembly of fibre
optic mechanical splices, fibre
management systems and closures
IEC 61300-2-46 - Fibre optic interconnecting devices and EN IEC 61300-2-46 -
passive components - Basic test and
measurement procedures - Part 2–46:
Tests - Damp heat, cyclic
IEC 61300-3-3 - Fibre optic interconnecting devices and EN 61300-3-3 -
passive components - Basic test and
measurement procedures - Part 3–3:
Examinations and measurements - Active
monitoring of changes in attenuation and
return loss
IEC 61300-3-4 - Fibre optic interconnecting devices and EN 61300-3-4 -
passive components - Basic test and
measurement procedures - Part 3–4:
Examinations and measurements -
Attenuation
IEC 61300-3-6 - Fibre optic interconnecting devices and EN 61300-3-6 -
passive components - Basic test and
measurement procedures - Part 3–6:
Examinations and measurements - Return
loss
IEC 61300-3-7 - Fibre optic interconnecting devices and EN IEC 61300-3-7 -
passive components - Basic test and
measurement procedures - Part 3–7:
Examinations and measurements -
Wavelength dependence of attenuation
and return loss of single mode components
IEC 61300-3-28 - Fibre optic interconnecting devices and EN 61300-3-28 -
passive components - Basic test and
measurement procedures - Part 3–28:
Examinations and measurements -
Transient loss
IEC 61753-1 - Fibre optic interconnecting devices and EN IEC 61753-1 -
passive components - Performance
standard - Part 1: General and guidance
IEC 61756-1 - Fibre optic interconnecting devices and EN IEC 61756-1 -
passive components - Interface standard
for fibre management systems - Part 1:
General and guidance
IEC 61753-131-03 ®
Edition 1.0 2021-10
INTERNATIONAL
STANDARD
NORME
INTERNATIONALE
Fibre optic interconnecting devices and passive components – Performance
standard –
Part 131-03: Single-mode mechanical fibre splice for category OP – Outdoor
protected environment
Dispositifs d’interconnexion et composants passifs fibroniques – Norme de
performance –
Partie 131-03: Épissure mécanique de fibres unimodales pour catégorie OP –
Environnement extérieur protégé
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
COMMISSION
ELECTROTECHNIQUE
INTERNATIONALE
ICS 33.180.20 ISBN 978-2-8322-1029-3
– 2 – IEC 61753-131-03:2021 © IEC 2021
CONTENTS
FOREWORD . 3
1 Scope . 5
2 Normative references . 5
3 Terms and definitions . 6
4 General requirements . 7
4.1 General . 7
4.2 Storage, transportation and packaging . 7
4.3 Marking and identification . 7
4.4 Materials . 8
5 Test . 8
5.1 General . 8
5.2 Test sample preparation . 8
5.3 Test and measurement methods . 8
5.4 Acceptance criteria . 9
5.5 Test report . 9
6 Performance tests, test severities and pass/fail requirements . 9
6.1 Sample size, sequencing and grouping . 9
6.2 Dimensions . 9
6.3 Installation yield requirement . 9
6.4 Pass/fail criteria . 9
6.5 Detailed performance requirements tests . 11
Annex A (normative) Fibre type for test samples .
...
Questions, Comments and Discussion
Ask us and Technical Secretary will try to provide an answer. You can facilitate discussion about the standard in here.